Skip to contentSkip to conversation

Linux router responds to any ARP query when iproute2 xfrm policies are configured for an IPSec tunnel. What's going on?

DISCUSSION Jarkko Oranen 1 participant 2 messages Jan 16, 2020 – Jan 17, 2020

lore
Share & tools
lore
#0 lore raw

Hi,

First of all, I'm not currently subscribed to LKML, so please CC any replies.

I recently debugged a DHCP client which refused to accept a lease, and noticed that my router seems to reply to ARP requests for any IP address, apparently causing the client to think it was receiving a duplicate IP.

After some debugging, I learned that my router will respond to any ARP query if the IP falls within the traffic selector I'm using for my xfrm interface-based IPSec VPN. For example:

$ arping 1.1.1.1

ARPING 1.1.1.1 from 10.21.1.10 enp7s0

Unicast reply from 1.1.1.1 [00:0D:B9:4B:07:C1] 1.449ms

I tried changing the various ARP-related sysctls, but they had no effect on this behaviour. It stops immediately if I kill the IPSec tunnel and the xfrm policies are removed.

The xfrm interface is created simply with
ip link add st0 type xfrm dev eth0 if_id 1
and 10/8 is routed to it, though this doesn't seem to matter.

When the IPSec tunnel is up and running, it configures xfrm policies like so:

src 0.0.0.0/0 dst 0.0.0.0/0

	dir out priority 399999 ptype main

	tmpl src <my-ip> dst <remote-ip>

		proto esp spi 0xc5a3f611 reqid 1 mode tunnel

	if_id 0x1

src 0.0.0.0/0 dst 0.0.0.0/0

dir fwd priority 399999 ptype main

tmpl src <remote-ip> dst <my-ip>

proto esp reqid 1 mode tunnel

if_id 0x1

src 0.0.0.0/0 dst 0.0.0.0/0

dir in priority 399999 ptype main

tmpl src <remote-ip> dst <my-ip>

proto esp reqid 1 mode tunnel

if_id 0x1

src 0.0.0.0/0 dst 0.0.0.0/0

socket in priority 0 ptype main

src 0.0.0.0/0 dst 0.0.0.0/0

socket out priority 0 ptype main

src 0.0.0.0/0 dst 0.0.0.0/0

socket in priority 0 ptype main

src 0.0.0.0/0 dst 0.0.0.0/0

socket out priority 0 ptype main

src ::/0 dst ::/0

socket in priority 0 ptype main

src ::/0 dst ::/0

socket out priority 0 ptype main

src ::/0 dst ::/0

socket in priority 0 ptype main

src ::/0 dst ::/0

socket out priority 0 ptype main

The traffic selector affects what ARP requests the router responds to, so if I change it to 10.0.0.0/8, it will respond to any ARP request for IPs in that range.

This is happening on Alpine Linux running kernel version 5.4.12-1-lts.

Is this expected behaviour? I would appreciate some pointers.

--
Jarkko Oranen

#1 lore raw

Re: (Solved) Linux router responds to any ARP query when iproute2 xfrm policies are configured for an IPSec tunnel. What's going on?

Hi,

hopefully I got the In-Reply-To header right.

Turns out that while I thought I had disabled charon's fake-arp plugin, it was silently loading configuration from /etc/strongswan/charon I didn't expect it to load and despite the plugin being enabled, it made no indication that this is the case. I'll leave this here for Google in case someone else stubs their toe on this.

Sorry for the noise.

--

Jarkko