Skip to contentSkip to conversation

timeout waiting for DMA

DISCUSSION Jasmeet Sidhu 1 participant 1 message Feb 26, 2001

lore
Share & tools
lore
#0 lore raw
Quoted 95 lines

Date: Mon, 26 Feb 2001 12:47:30 -0800
To: Jason Rappleye <[email protected]>
From: Jasmeet Sidhu <[email protected]>
Subject: Re: timeout waiting for DMA

I had the same exact problem last night using the IBM drives and the ULTRA ata/100 controller from Promise. Could this be due to an irq conflict?

kernel: hda: timeout waiting for DMA
kernel: ide_dmaproc: chipset supported ide_dma_timeout func only: 14
kernel: hdi: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }

and after a few messages my system freazes and can only be brought up by a hard reset. Could this be due to faulty cables as well? or is there something else that is messing up? I was suspecting an IRQ problem, maybe USB is using the same irq (nothing on the USB ports though)... but I am not certain. Anybody else out there with similar problems? Any Solutions?

This was suing Kernel 2.4.2 with ac3 patch. Is there a need to apply Andre Hedrick's ide patches from kernel 2.4.1?

Jasmeet

Quoted 67 lines · you

Hi,

I'm running kernel 2.4.2 on an SGI 1100 (dual PIIIs) with a Serverworks III LE based motherboard. The disk is a Seagate ST330630A. The disk has DMA enabled at boot time :

hda: ST330630A, ATA DISK drive
hda: 59777640 sectors (30606 MB) w/2048KiB Cache, CHS=3720/255/63, UDMA(33)

(also verified using hdparm)

but after a while (eg partway through running bonnie with a 1GB file) I get the following errors:

Feb 24 22:51:02 nash2 kernel: hda: timeout waiting for DMA
Feb 24 22:51:02 nash2 kernel: ide_dmaproc: chipset supported ide_dma_timeout
func only: 14
Feb 24 22:51:02 nash2 kernel: hda: irq timeout: status=0x58 { DriveReady
SeekComplete DataRequest }
<repeats a few times>
Feb 24 22:51:32 nash2 kernel: hda: DMA disabled

I can reenable DMA without any problems, but after some additional disk activity (eg running bonnie again), the error occurs again.

Additional information on my hardware is given below. Any suggestions on how this can be resolved?

Thanks,

Jason

hdparm -i /dev/hda

/dev/hda:

Model=ST330630A, FwRev=3.21, SerialNo=3CK0JDFE
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=0(?), BuffSize=2048kB, MaxMultSect=16, MultSect=off DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2 CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=59777640 tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2 IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4 UDMA modes: mode0 mode1 *mode2 mode3 mode4

Relevant portion of /proc/pci:

Bus 0, device 15, function 1:

    IDE interface: PCI device 1166:0211 (ServerWorks) (rev 0).
      Master Capable.  Latency=64.
      I/O at 0x3080 [0x308f].

Relevant portion of lspci -v:

00:0f.1 IDE interface: Relience Computer: Unknown device 0211 (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 64
I/O ports at 3080 [size=16]

--
Jason Rappleye
[email protected]
http://www.ccr.buffalo.edu/jason.htm

Quoted 5 lines

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Quoted 6 lines

- - -
Jasmeet Sidhu
Unix Systems Administrator
ArrayComm, Inc.
[email protected]
www.arraycomm.com

- - -
Jasmeet Sidhu
Unix Systems Administrator
ArrayComm, Inc.
[email protected]
www.arraycomm.com