Skip to contentSkip to conversation

BLE - multiple connections

DISCUSSION Ajay KV 5 participants 11 messages Jul 20, 2012 – Aug 23, 2012 2 messages not in the archive Bluetooth drivers

lore
Share & tools
lore

Ajay KV

author
#0 lore raw

Hi all,

Since im new to bluetooth low energy technology , i need some guidance from you . Following are the issues that im searching for a solution

1 : Is it possible to establish mutiple LE connection at a time . Im using fedora 13 , linux 2.6.39 version with 4.0 LE supported dongles

2: now im not concentrating on user profiles like GATT and ATT . i wanted to do it using HCI and L2cap connections

Thanks and Regards

#1 lore raw

Hi Ajay,

Quoted 7 lines · Ajay KV

Hi all,

Since im new to bluetooth low energy technology , i need some guidance from you . Following are the issues that im searching for a solution

Quoted 5 lines

1 : Is it possible to establish mutiple LE connection at a time . Im using fedora 13 , linux 2.6.39 version with 4.0 LE supported dongles

2: now im not concentrating on user profiles like GATT and ATT . i wanted to do it using HCI and L2cap connections

You are able to establish one LE connection at a time. If you have more than one device you want to connect to, you can use whitelist. Add the devices to whitelist and issue the LE connection command. As soon as one of the devices starts advertising, the connection will be established.

You can use hcitool to add devices to whitelist and issue LE connection command.

BR,

Andre

author
#2 lore raw

Hi,
So that means at a time i can not able to establish two LE
active connections. One more task i wanna try is to send L2cap data packets through L2cap signalling channel (cid 0x05) . But as per my knowledge kernel has designed it to work only on cid 0x05

Quoted 30 lines · Andre Guedes

Hi Ajay,

Quoted 6 lines · Ajay KV

Hi all,

Since im new to bluetooth low energy technology , i need some guidance from you . Following are the issues that im searching for a solution

Quoted 6 lines

1 : Is it possible to establish mutiple LE connection at a time . Im using fedora 13 , linux 2.6.39 version with 4.0 LE supported dongles

2: now im not concentrating on user profiles like GATT and ATT . i wanted to do it using HCI and L2cap connections

You are able to establish one LE connection at a time. If you have more than one device you want to connect to, you can use whitelist. Add the devices to whitelist and issue the LE connection command. As soon as one of the devices starts advertising, the connection will be established.

You can use hcitool to add devices to whitelist and issue LE connection command.

BR,

Andre

#3 lore raw
Quoted 39 lines · Ajay KV

Hi,
So that means at a time i can not able to establish two LE
active connections. One more task i wanna try is to send L2cap
data packets through L2cap signalling channel (cid 0x05) . But as per my knowledge kernel has designed it to work only on cid 0x05

Quoted 30 lines · Andre Guedes

Hi Ajay,

Quoted 7 lines · Ajay KV

Hi all,

Since im new to bluetooth low energy technology , i need some guidance from
you . Following are the issues that im searching for a solution

Quoted 7 lines

1 : Is it possible to establish mutiple LE connection at a time . Im using
fedora 13 , linux 2.6.39 version with 4.0 LE supported dongles

2: now im not concentrating on user profiles like GATT and ATT . i wanted to
do it using HCI and L2cap connections

You are able to establish one LE connection at a time. If you have more than one device you want to connect to, you can use whitelist. Add the devices to whitelist and issue the LE connection command. As soon as one of the devices starts advertising, the connection will be established.

You can use hcitool to add devices to whitelist and issue LE connection command.

BR,

Quoted 8 lines
Quoted 2 lines

Andre

--
To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

As Andre said - you can not create multiple connections at the same time, but you can have multiple active connections at the same time. The only limitation is during the connection creation procedure. After an LE connection has been established to device A, you can create a second LE connection to device B.

BR,
Chen Ganir
Texas Instruments.

#5 lore raw
In reply to Ajay KV

Hi,

Quoted 10 lines · Ajay KV

1: suppose device A and B is in connected state (B as initiator and A as advertising mode) , so obviously role change happens and A switches to slave mode . meanwhile i wanted to connect device C to A (C as initiator and A as advertising mode) , since A has switched to slave mode , it cant able to advertise again ( controller returns error message " command disallowed") . Even i tried to change the role forcefully through hcitool command , the result was same.
My intention is to make the device A as a server with multiple
clients. Currently im not using any of the profiles(ATT , GATT) . i want it to be done using L2CAP sockets

You need to check if your controller supports the LE state combinations you are trying to use. Run "hciconfig hci0 lestates" And check the supported states. Also see Core Spec v4.0 page 1096 for more details.

Some controllers don't support LE scanning and LE advertising at the same time, so make sure you don't have LE scanning enabled in "A" while trying to re-enable advertising.

Quoted 2 lines

2. Is it possible to change the imtu of the LE connection other than 23bits( which is hardcoded in L2cap driver)

I think this was fixed on more recent kernel releases. See patches from Andre Guedes around May 31st (which are already upstream).

Best Regards,

Signature · 3 lines
Anderson Lizardo
Instituto Nokia de Tecnologia - INdT
Manaus - Brazil
author
#4 lore raw
In reply to Andre Guedes

Hi ,
I am facing some more issues regarding BLE multiple connection
, which is mentioned below . please show me the right direction , since i got stucked

1: suppose device A and B is in connected state (B as initiator and A as advertising mode) , so obviously role change happens and A switches to slave mode . meanwhile i wanted to connect device C to A (C as initiator and A as advertising mode) , since A has switched to slave mode , it cant able to advertise again ( controller returns error message " command disallowed") . Even i tried to change the role forcefully through hcitool command , the result was same.
My intention is to make the device A as a server with
multiple clients. Currently im not using any of the profiles(ATT , GATT) . i want it to be done using L2CAP sockets

2. Is it possible to change the imtu of the LE connection other than 23bits( which is hardcoded in L2cap driver)

Quoted 29 lines · Andre Guedes

Hi Ajay,

Quoted 6 lines · Ajay KV

Hi all,

Since im new to bluetooth low energy technology , i need some guidance from you . Following are the issues that im searching for a solution

Quoted 6 lines

1 : Is it possible to establish mutiple LE connection at a time . Im using fedora 13 , linux 2.6.39 version with 4.0 LE supported dongles

2: now im not concentrating on user profiles like GATT and ATT . i wanted to do it using HCI and L2cap connections

You are able to establish one LE connection at a time. If you have more than one device you want to connect to, you can use whitelist. Add the devices to whitelist and issue the LE connection command. As soon as one of the devices starts advertising, the connection will be established.

You can use hcitool to add devices to whitelist and issue LE connection command.

BR,

Andre

#9 lore raw
In reply to Ajay KV

Hi Ajay,

Quoted 2 lines · Ajay KV

i could not able to figure it out yet , why its showing this error
" command disallowed" . Here im using fedora 13 with kernel 2.6.39 . i tried

This kernel is too old. For sure a lot of LE stuff will not work correctly on it. Can you try compiling your own kernel (latest version) and use tha latest BlueZ version with it?

Quoted 4 lines

with both dongles , iogear and cirago . But the result is same. i dont think that its something wrong with kernel version, as we uses hci commands (hciconfig hci0 leadv ) that directly talks with controller . please clear this issue..

Sorry, but I ran out of ideas. Can you describe with more details which exact steps are you taking to get the "command disallowed" HCI error? I.e. right after you attach the dongle, which commands are you issuing.

Also an hcidump showing the entire session (since the dongle is attached) should help. Without more information we are not unable to help further.

Regards,

Signature · 3 lines
Anderson Lizardo
Instituto Nokia de Tecnologia - INdT
Manaus - Brazil
#10 lore raw
In reply to Ajay KV

Hi,

Quoted 25 lines · Ajay KV
Quoted 18 lines · Anderson Lizardo

Hi Ajay

[your emails to BlueZ mailing list may be getting blocked because you are using HTML. Please fix that on your mail client. Also remember to not top-post]

Quoted 11 lines · Ajay KV

Thanks for your reply. i have 2 dongles of different made (iogear and chirago) . "Hciconfig hci0 lestates" gives this following result

Supported link layer states:
[...]

Here my issue is to know whether (connected mode + advertising
mode) is possible at a time . Once A is connected to B (initiator), i could not able to enable advertise in A (getting command disallowed ) , so that device C is not getting the connectable advertising packets on scanning.

Quoted 5 lines

I could not see any reason to get "command disallowed" when enabling LE adv. Did you try changing dongle combinations to make sure it is not some hardware issue?

Regards,

Quoted 7 lines

Hi,
i could not able to figure it out yet , why its showing
this error " command disallowed" . Here im using fedora 13 with kernel 2.6.39 . i tried with both dongles , iogear and cirago . But the result is same. i dont think that its something wrong with kernel version, as we uses hci commands (hciconfig hci0 leadv ) that directly talks with controller . please clear this issue..

Most probably the controller is in the page scan or inquiry scan state. Try doing 'hciconfig hci0 noscan', before enabling advertising.

Quoted 6 lines

--
To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Cheers,

Signature · 1 line
Vinicius
author
#8 lore raw
In reply to a message not in the archive
Quoted 20 lines · Anderson Lizardo

Hi Ajay

[your emails to BlueZ mailing list may be getting blocked because you are using HTML. Please fix that on your mail client. Also remember to not top-post]

Quoted 12 lines · Ajay KV

Thanks for your reply. i have 2 dongles of different made (iogear and chirago) . "Hciconfig hci0 lestates" gives this following result

Supported link layer states:
[...]

Here my issue is to know whether (connected mode + advertising
mode) is possible at a time . Once A is connected to B (initiator), i could not able to enable advertise in A (getting command disallowed ) , so that device C is not getting the connectable advertising packets on scanning.

Quoted 6 lines

I could not see any reason to get "command disallowed" when enabling LE adv. Did you try changing dongle combinations to make sure it is not some hardware issue?

Regards,

Hi,
i could not able to figure it out yet , why its showing this
error " command disallowed" . Here im using fedora 13 with kernel 2.6.39 . i tried with both dongles , iogear and cirago . But the result is same. i dont think that its something wrong with kernel version, as we uses hci commands (hciconfig hci0 leadv ) that directly talks with controller . please clear this issue..

author
#11 lore raw
In reply to Vinicius Costa Gomes
Quoted 36 lines · Vinicius Costa Gomes

Hi,

Quoted 25 lines · Ajay KV
Quoted 18 lines · Anderson Lizardo

Hi Ajay

[your emails to BlueZ mailing list may be getting blocked because you are using HTML. Please fix that on your mail client. Also remember to not top-post]

Quoted 11 lines · Ajay KV

Thanks for your reply. i have 2 dongles of different made (iogear and chirago) . "Hciconfig hci0 lestates" gives this following result

Supported link layer states:
[...]

Here my issue is to know whether (connected mode + advertising
mode) is possible at a time . Once A is connected to B (initiator), i could not able to enable advertise in A (getting command disallowed ) , so that device C is not getting the connectable advertising packets on scanning.

Quoted 5 lines

I could not see any reason to get "command disallowed" when enabling LE adv. Did you try changing dongle combinations to make sure it is not some hardware issue?

Regards,

Quoted 7 lines

Hi,
i could not able to figure it out yet , why its showing
this error " command disallowed" . Here im using fedora 13 with kernel 2.6.39 . i tried with both dongles , iogear and cirago . But the result is same. i dont think that its something wrong with kernel version, as we uses hci commands (hciconfig hci0 leadv ) that directly talks with controller . please clear this issue..

Quoted 5 lines

Most probably the controller is in the page scan or inquiry scan state. Try doing 'hciconfig hci0 noscan', before enabling advertising.

Cheers,

Hi,
Still not working , getting the same old error. i just want to know ,
whether my dual-mode dongle allows this operation or not (Advertising mode+ connected mode)

Regards,

#12 lore raw

Hi Ajay,

Quoted 3 lines · Ajay KV

Still not working , getting the same old error. i just want to know
, whether my dual-mode dongle allows this operation or not (Advertising mode+ connected mode)

Did you try my suggestion?

1) Enable LE adv on A
2) Connect from B to A
3) Try to enable LE adv on A (should give the error you are getting)
4) disconnect connection from A side (using hcitool ledc)
5) try to enable LE adv on A

if step (5) works, we have confirmation that a dual mode dongle in slave mode is not accepting more than one active connection.

Anyway, I finally found the section from Core Spec v4.0, where it clearly says that a LE device operating in slave mode does not accept more than one connection (but a master device can create multiple connections). See Vol. 6, Part B, Section 1.1.1 "State and Role Combination Restrictions" (page 2195), specially second bullet. I copy the relevant text here:

"""
The Link Layer may optionally support multiple state machines. If it does support multiple state machines, the following state and role restrictions shall apply.
* The Link Layer in the Connection State shall not operate in the Master Role and Slave Role at the same time.
* The Link Layer in the Connection State operating in the Slave Role shall have only one connection.
[...]
"""

That means you can't send connectable advertising from a slave LE device if one connection is active.

Best regards,

Signature · 3 lines
Anderson Lizardo
Instituto Nokia de Tecnologia - INdT
Manaus - Brazil