Skip to contentSkip to conversation

uda1380 and pxa255 plays nothing but noise

DISCUSSION nerwusek 3 participants 11 messages Aug 7, 2012 – Aug 9, 2012

lore
Share & tools
lore

nerwusek

author
#0 lore raw

Hello,
I'm trying to enable sound on my iPAQ h2200 device using ALSA ASoC. I've created driver basing on hx4700.c and magician.c files, but I can't hear is anything. When I am playing music on device file uda1380-codec.0-0018/dapm/Playback shows that stream Playback is active, but in DAC that stream is inactive (but DAC is on). I also noticed that on I2S bus is nothing going on. I've lost many hours on looking for problem. Is there anyone who could help me?

Łukasz Dałek

#1 lore raw
Quoted 7 lines · nerwusek

I'm trying to enable sound on my iPAQ h2200 device using ALSA ASoC. I've created driver basing on hx4700.c and magician.c files, but I can't hear is anything. When I am playing music on device file uda1380-codec.0-0018/dapm/Playback shows that stream Playback is active, but in DAC that stream is inactive (but DAC is on). I also noticed that on I2S bus is nothing going on. I've lost many hours on looking for problem. Is there anyone who could help me?

Have you checked that the output isn't muted, has the audio routed to the output you're using and has a suitable volume?

author
#2 lore raw
Quoted 11 lines · Mark Brown
Quoted 7 lines · nerwusek

I'm trying to enable sound on my iPAQ h2200 device using ALSA ASoC. I've created driver basing on hx4700.c and magician.c files, but I can't hear is anything. When I am playing music on device file uda1380-codec.0-0018/dapm/Playback shows that stream Playback is active, but in DAC that stream is inactive (but DAC is on). I also noticed that on I2S bus is nothing going on. I've lost many hours on looking for problem. Is there anyone who could help me?

Have you checked that the output isn't muted, has the audio routed to the output you're using and has a suitable volume?

author
#3 lore raw
In reply to Mark Brown
Quoted 1 line · Mark Brown

Have you checked that the output isn't muted, has the audio routed to the output you're using and has a suitable volume?

Yes I have checked all that things. I have 2 routes from VOUTHP{LR} and from VOUT{LR} and I think it's ok because of info in logs "asoc: uda1380-hifi <-> pxa2xx-i2s mapping ok".
I have also observed that if I change Output Mux from DAC to Analog Mixer and change Anolog Mixer volume up the noise and louder.
In my opinion problem is somewhere else. I think that I forgot to enable sth in ALSA. As I said when I enabled I2C debugging data flows only when playback is starting or when I change values in alsamixer, when music is played no data are send to codec.

Łukasz Dałek

#4 lore raw

Maybe some amplifier is not enabled? On iPAQ h1940 and rx1950 you need to toggle gpio pin to hear something from internal speaker (not sure if that pin disables
headphones).

Anyway, you can just mimic WinMobile behavior, use haret to see if there's some GPIO activity. If you need to learn some haret magic - just ask me :)

Regards
Vasily

Quoted 15 lines · nerwusek
Quoted 3 lines · Mark Brown

Have you checked that the output isn't muted, has the audio routed to the output you're using and has a suitable volume?

Yes I have checked all that things. I have 2 routes from VOUTHP{LR} and from VOUT{LR} and I think it's ok because of info in logs "asoc: uda1380-hifi <-> pxa2xx-i2s mapping ok".
I have also observed that if I change Output Mux from DAC to Analog Mixer and change Anolog Mixer volume up the noise and louder.
In my opinion problem is somewhere else. I think that I forgot to enable sth in ALSA. As I said when I enabled I2C debugging data flows only when playback is starting or when I change values in alsamixer, when music is played no data are send to codec.

Quoted 6 lines

Łukasz Dałek

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#10 lore raw
In reply to nerwusek
Quoted 5 lines · nerwusek
Quoted 3 lines · Mark Brown

Have you checked that the output isn't muted, has the audio routed to the output you're using and has a suitable volume?

Quoted 9 lines

Yes I have checked all that things. I have 2 routes from VOUTHP{LR} and from VOUT{LR} and I think it's ok because of info in logs "asoc: uda1380-hifi <-> pxa2xx-i2s mapping ok".
I have also observed that if I change Output Mux from DAC to Analog Mixer and change Anolog Mixer volume up the noise and louder.
In my opinion problem is somewhere else. I think that I forgot to enable sth in ALSA. As I said when I enabled I2C debugging data flows only when playback is starting or when I change values in alsamixer, when music is played no data are send to codec.

Audio data should be sent over I2S, so there's no I2C traffic during audio playback.

Regards
Vasily

Quoted 1 line

Łukasz Dałek

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

author
#5 lore raw
In reply to Vasily Khoruzhick
Quoted 4 lines · Vasily Khoruzhick

Maybe some amplifier is not enabled? On iPAQ h1940 and rx1950 you need to toggle gpio pin to hear something from internal speaker (not sure if that pin disables
headphones).

When I change volume of Analog Mixer the noise in headphones is getting stronger or weaker so GPIOs in my opinion are set up correctly.

I'll enable debug messages on i2s bus and see if there is sth sent to codec. Maybe alsa is sending music packets to /dev/null.

I will also want to see what debugfs files should contain when audio works. Could you send me few examples or point me to address with them?

Łukasz Dałek

#6 lore raw
Quoted 7 lines · nerwusek
Quoted 5 lines · Vasily Khoruzhick

Maybe some amplifier is not enabled? On iPAQ h1940 and rx1950 you need to toggle gpio pin to hear something from internal speaker (not sure if that pin disables
headphones).

Quoted 8 lines

When I change volume of Analog Mixer the noise in headphones is getting stronger or weaker so GPIOs in my opinion are set up correctly.

I'll enable debug messages on i2s bus and see if there is sth sent to codec. Maybe alsa is sending music packets to /dev/null.

I will also want to see what debugfs files should contain when audio works. Could you send me few examples or point me to address with them?

Well, I've no compiled kernel nor rootfs for my PDAs :( and I'll be pretty busy this weekend,
so it'll take some time to get debugfs contents for you.

Regards
Vasily

#7 lore raw
In reply to nerwusek
Quoted 2 lines · nerwusek

When I change volume of Analog Mixer the noise in headphones is getting stronger or weaker so GPIOs in my opinion are set up correctly.

This sounds like either the CPU isn't actually sending data or there's a digital mute.

author
#8 lore raw
Quoted 1 line · Mark Brown

This sounds like either the CPU isn't actually sending data or there's a digital mute.

Debugfs file asoc/ipaq/uda.../dapm/Playback shows:
Playback: On in 1 out 1
stream Playback active
out "static" "DAC"
out "static" "DAC"
out "static" "DAC"

and file DAC shows:
DAC: On in 3 out 4 - R2(0x2) bit 10
stream Playback inactive

 in  "static" "Playback"
 in  "static" "Playback"
 in  "static" "Playback"

out "DAC" "Output Mux"
out "static" "Analog Mixer"

is it correct? Shouldn't stream Playback in DAC show active status? Also I noticed that alsamixer works slower when playing music so some data must be sent to codec but I don't know is that music data or sth else.

Łukasz Dałek

author
#9 lore raw
Quoted 18 lines · nerwusek
Quoted 1 line · Mark Brown

This sounds like either the CPU isn't actually sending data or there's a digital mute.

Debugfs file asoc/ipaq/uda.../dapm/Playback shows:
Playback: On in 1 out 1
stream Playback active
out "static" "DAC"
out "static" "DAC"
out "static" "DAC"

and file DAC shows:
DAC: On in 3 out 4 - R2(0x2) bit 10
stream Playback inactive

 in  "static" "Playback"
 in  "static" "Playback"
 in  "static" "Playback"

out "DAC" "Output Mux"
out "static" "Analog Mixer"

Quoted 6 lines

is it correct? Shouldn't stream Playback in DAC show active status? Also I noticed that alsamixer works slower when playing music so some data must be sent to codec but I don't know is that music data or sth else.

Łukasz Dałek

I also booted handhelds kernel (2.6.21) and compared UDA registers with it. Everything was the same except in my kernel (3.4) was silence. At this point I have no idea where is the problem.

Łukasz Dałek