Packet loss on bcm4331
I have a MacBook with a bcm4331 chip which mostly works in Linux (Fedora 17 w/kernel 3.5.1), but I'm noticing horrible packet loss and throughput a lot of the time.
The setup is basically a small apartment with an 802.11bgn router sitting in the living room; I've had the laptop sit directly on top of the router and run ping to another computer wired directly into the access point and experienced 75% packet loss. File transfers are experiencing throughput in the region of 200kB/s to 800kB/s. Oddly enough, the amount of packet loss is significantly reduced if I'm connected in my bedroom (~20 feet from the router and with a couple of walls in between). I've also experienced the same problems with my backup wireless router (a WRT54GL running dd-wrt).
By comparison, on OS X I get 0% packet loss and throughput in the region of 2MB-3MB/s.
System information:
[george at aluminium ~]$ uname -a
Linux aluminium 3.5.1-1.fc17.x86_64 #1 SMP Thu Aug 9 17:50:43 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux
[george at aluminium ~]$ lspci -vnn | grep 43 -A7 04:00.0 Network controller [0280]: Broadcom Corporation BCM4331 802.11a/b/g/n [14e4:4331] (rev 02)
Subsystem: Apple Computer Inc. Device [106b:00ef]
Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at c1900000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: bcma-pci-bridge
In dmesg the relevant messages seem to be:
[ 3062.855352] wlan0: authenticate with d8:c7:c8:eb:08:20 [ 3062.865459] wlan0: direct probe to d8:c7:c8:eb:08:20 (try 1/3) [ 3063.065716] wlan0: direct probe to d8:c7:c8:eb:08:20 (try 2/3) [ 3063.266339] wlan0: direct probe to d8:c7:c8:eb:08:20 (try 3/3) [ 3063.466953] wlan0: authentication with d8:c7:c8:eb:08:20 timed out [ 3063.707190] wlan0: authenticate with d8:c7:c8:eb:0a:40 [ 3063.716868] wlan0: direct probe to d8:c7:c8:eb:0a:40 (try 1/3) [ 3063.917113] wlan0: direct probe to d8:c7:c8:eb:0a:40 (try 2/3) [ 3064.117756] wlan0: direct probe to d8:c7:c8:eb:0a:40 (try 3/3) [ 3064.318329] wlan0: authentication with d8:c7:c8:eb:0a:40 timed out [ 3064.563442] wlan0: authenticate with d8:c7:c8:eb:06:e0 [ 3064.563696] wlan0: send auth to d8:c7:c8:eb:06:e0 (try 1/3) [ 3064.763538] wlan0: send auth to d8:c7:c8:eb:06:e0 (try 2/3) [ 3064.771511] wlan0: authenticated [ 3064.772525] wlan0: associate with d8:c7:c8:eb:06:e0 (try 1/3) [ 3064.782600] wlan0: RX AssocResp from d8:c7:c8:eb:06:e0 (capab=0x431 status=0 aid=7) [ 3064.782775] wlan0: associated [ 3107.530689] ieee80211 phy0: wlan0: No probe response from AP d8:c7:c8:eb:06:e0 after 500ms, disconnecting. [ 3107.552816] cfg80211: Calling CRDA to update world regulatory domain [ 3107.555845] cfg80211: World regulatory domain updated: [ 3107.555850] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 3107.555854] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 3107.555856] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 3107.555858] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 3107.555860] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 3107.555863] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 3107.556124] cfg80211: Calling CRDA for country: CA [ 3107.559776] cfg80211: Regulatory domain changed to country: CA [ 3107.559781] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 3107.559786] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 3107.559790] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 3107.559794] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 3107.559798] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 3107.559801] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300
mBi, 3000 mBm)
I'm loading the b43 module with the following parameters:
options b43 nohwcrypt=1 qos=0 hwpctl=1
I've also tried it with hwpctl=0 to no avail.
Can anyone suggest what may be going on here?
Thanks,
George
Quoted 4 lines · George Wright
I have a MacBook with a bcm4331 chip which mostly works in Linux (Fedora 17 w/kernel 3.5.1), but I'm noticing horrible packet loss and throughput a lot of the time.
Quoted 9 lines
The setup is basically a small apartment with an 802.11bgn router sitting in the living room; I've had the laptop sit directly on top of the router and run ping to another computer wired directly into the access point and experienced 75% packet loss. File transfers are experiencing throughput in the region of 200kB/s to 800kB/s. Oddly enough, the amount of packet loss is significantly reduced if I'm connected in my bedroom (~20 feet from the router and with a couple of walls in between). I've also experienced the same problems with my backup wireless router (a WRT54GL running dd-wrt).
In b43, power management of 802.11n devices has never been implemented in the fullest form. Thus, it is likely that the gain setting is too high when you are close to the AP and the resulting distortion is causing failures.
Quoted 2 lines
By comparison, on OS X I get 0% packet loss and throughput in the region of 2MB-3MB/s.
As Broadcom knows the specs for the device, they could get it right. We have to rely on reverse engineering.
--snip--
Quoted 7 lines
I'm loading the b43 module with the following parameters:
options b43 nohwcrypt=1 qos=0 hwpctl=1
I've also tried it with hwpctl=0 to no avail.
Can anyone suggest what may be going on here?
It is unlikely that any of the options will make any difference in this case..
Larry
2012/8/14 Larry Finger <[email protected]>:
Quoted 17 lines · George Wright
Quoted 5 lines
I have a MacBook with a bcm4331 chip which mostly works in Linux (Fedora 17 w/kernel 3.5.1), but I'm noticing horrible packet loss and throughput a lot of the time.
Quoted 9 lines
The setup is basically a small apartment with an 802.11bgn router sitting in the living room; I've had the laptop sit directly on top of the router and run ping to another computer wired directly into the access point and experienced 75% packet loss. File transfers are experiencing throughput in the region of 200kB/s to 800kB/s. Oddly enough, the amount of packet loss is significantly reduced if I'm connected in my bedroom (~20 feet from the router and with a couple of walls in between). I've also experienced the same problems with my backup wireless router (a WRT54GL running dd-wrt).
Quoted 3 lines
In b43, power management of 802.11n devices has never been implemented in the fullest form. Thus, it is likely that the gain setting is too high when you are close to the AP and the resulting distortion is causing failures.
I promise to work on this, but I can provide only N-PHY support (we have specs for them). I'll try my best to do some power management for N-PHY for 3.7 merge window.
Right now I'm focused on SoC support for my BCM4706 SoC. But fortunately I'm getting everything pushed upstream slowly.
Unfortunately BCM4331 is HT-PHY which I can't really improve. We don't have any specs about that PHY type and support is mostly pure luck.
I may try to improve is a little since I get BCM4706 support (my SoC has two BCM4331 connected via PCIE), but don't expect much :(
Signature · 1 line
Rafa?