Skip to contentSkip to conversation

Problems w/Sandy Bridge & 27" monitor

DISCUSSION Chun-Yu Shei 2 participants 7 messages Aug 15, 2012 – Aug 27, 2012

lore
Share & tools
lore
#0 lore raw

Hi,

I recently upgraded to a 27" monitor (2560x1440) from a 23" one (1920x1080), and had to switch to Windows because the new monitor is unusable in Linux. Today, about a month later, I decided to give Linux another try, since there have been several updates to the Intel graphics driver since then.

Unfortunately, it seems that it's still unusable with xf86-video-intel 2.20.3 -- after a little while, the video signal to the 27" monitor completely stops, and it goes into power saving mode. I'm running dual monitors with the old 23", and that one continues running fine when this happens. This happens on my ThinkPad X220 (i5-2540M). The 27" is connected via DisplayPort, and the 23" via DVI. SNA is enabled, if it makes any difference (I haven't tried turning it off, but I probably should). This is the biggest problem I'm facing when it comes to Linux support.

I also gave the new "TearFree" option a try, and while it does a great job of eliminating tearing, it makes the two monitors become mirrors of each other for some reason. If I take a screenshot with the GNOME tool, the screenshot comes out as expected (unmirrored), but the video output on the two monitors is mirrored in reality. Disabling "TearFree" fixes this.

Also, when I'm using the ThinkPad's built-in display, it sometimes turns off for no apparent reason, although it's not too big of a deal since a suspend/resume cycle seems to fix things (and I haven't used 2.20.3 long enough to experience this yet).

Any ideas/things I can do to help track these issues down?

Thanks,
Chun-Yu

#1 lore raw
Quoted 25 lines · Chun-Yu Shei

Hi,

I recently upgraded to a 27" monitor (2560x1440) from a 23" one (1920x1080), and had to switch to Windows because the new monitor is unusable in Linux. Today, about a month later, I decided to give Linux another try, since there have been several updates to the Intel graphics driver since then.

Unfortunately, it seems that it's still unusable with xf86-video-intel 2.20.3 -- after a little while, the video signal to the 27" monitor completely stops, and it goes into power saving mode. I'm running dual monitors with the old 23", and that one continues running fine when this happens. This happens on my ThinkPad X220 (i5-2540M). The 27" is connected via DisplayPort, and the 23" via DVI. SNA is enabled, if it makes any difference (I haven't tried turning it off, but I probably should). This is the biggest problem I'm facing when it comes to Linux support.

I also gave the new "TearFree" option a try, and while it does a great job of eliminating tearing, it makes the two monitors become mirrors of each other for some reason. If I take a screenshot with the GNOME tool, the screenshot comes out as expected (unmirrored), but the video output on the two monitors is mirrored in reality. Disabling "TearFree" fixes this.

Quoted 6 lines

Also, when I'm using the ThinkPad's built-in display, it sometimes turns off for no apparent reason, although it's not too big of a deal since a suspend/resume cycle seems to fix things (and I haven't used 2.20.3 long enough to experience this yet).

Any ideas/things I can do to help track these issues down?

For the screen blanking issues, the kernel is the important part. Please boot with drm.debug=0xe added to your kernel bootline and grab the full dmesg.
-Daniel

Signature · 3 lines
Daniel Vetter
Mail: [email protected]
Mobile: +41 (0)79 365 57 48
#2 lore raw
Quoted 31 lines · Daniel Vetter
Quoted 30 lines · Chun-Yu Shei

Hi,

I recently upgraded to a 27" monitor (2560x1440) from a 23" one (1920x1080), and had to switch to Windows because the new monitor is unusable in Linux. Today, about a month later, I decided to give Linux another try, since there have been several updates to the Intel graphics driver since then.

Unfortunately, it seems that it's still unusable with xf86-video-intel 2.20.3 -- after a little while, the video signal to the 27" monitor completely stops, and it goes into power saving mode. I'm running dual monitors with the old 23", and that one continues running fine when this happens. This happens on my ThinkPad X220 (i5-2540M). The 27" is connected via DisplayPort, and the 23" via DVI. SNA is enabled, if it makes any difference (I haven't tried turning it off, but I probably should). This is the biggest problem I'm facing when it comes to Linux support.

I also gave the new "TearFree" option a try, and while it does a great job of eliminating tearing, it makes the two monitors become mirrors of each other for some reason. If I take a screenshot with the GNOME tool, the screenshot comes out as expected (unmirrored), but the video output on the two monitors is mirrored in reality. Disabling "TearFree" fixes this.

Also, when I'm using the ThinkPad's built-in display, it sometimes turns off for no apparent reason, although it's not too big of a deal since a suspend/resume cycle seems to fix things (and I haven't used 2.20.3 long enough to experience this yet).

Quoted 7 lines
Quoted 1 line

Any ideas/things I can do to help track these issues down?

For the screen blanking issues, the kernel is the important part. Please boot with drm.debug=0xe added to your kernel bootline and grab the full dmesg.
-Daniel

OK, I finally got around to doing this... I just upgraded to the 3.5.3 kernel and xf86-video-intel 2.20.5 as well.

Here's the initial dmesg upon bootup: http://pastebin.com/41F2AA0f

And here's the dmesg right after the 27" goes blank: http://pastebin.com/3CTRETQ4 (not completely blank, though... there are a few lines at the very left & top edge of the display)

A few seconds later, the display came back, and here's the dmesg right after that: http://pastebin.com/9mdfY5P1

Chun-Yu

#3 lore raw
Quoted 43 lines · Chun-Yu Shei
Quoted 31 lines · Daniel Vetter
Quoted 30 lines · Chun-Yu Shei

Hi,

I recently upgraded to a 27" monitor (2560x1440) from a 23" one (1920x1080), and had to switch to Windows because the new monitor is unusable in Linux. Today, about a month later, I decided to give Linux another try, since there have been several updates to the Intel graphics driver since then.

Unfortunately, it seems that it's still unusable with xf86-video-intel 2.20.3 -- after a little while, the video signal to the 27" monitor completely stops, and it goes into power saving mode. I'm running dual monitors with the old 23", and that one continues running fine when this happens. This happens on my ThinkPad X220 (i5-2540M). The 27" is connected via DisplayPort, and the 23" via DVI. SNA is enabled, if it makes any difference (I haven't tried turning it off, but I probably should). This is the biggest problem I'm facing when it comes to Linux support.

I also gave the new "TearFree" option a try, and while it does a great job of eliminating tearing, it makes the two monitors become mirrors of each other for some reason. If I take a screenshot with the GNOME tool, the screenshot comes out as expected (unmirrored), but the video output on the two monitors is mirrored in reality. Disabling "TearFree" fixes this.

Also, when I'm using the ThinkPad's built-in display, it sometimes turns off for no apparent reason, although it's not too big of a deal since a suspend/resume cycle seems to fix things (and I haven't used 2.20.3 long enough to experience this yet).

Quoted 7 lines
Quoted 1 line

Any ideas/things I can do to help track these issues down?

For the screen blanking issues, the kernel is the important part. Please boot with drm.debug=0xe added to your kernel bootline and grab the full dmesg.
-Daniel

OK, I finally got around to doing this... I just upgraded to the 3.5.3 kernel and xf86-video-intel 2.20.5 as well.

Quoted 8 lines

Here's the initial dmesg upon bootup: http://pastebin.com/41F2AA0f

And here's the dmesg right after the 27" goes blank:
http://pastebin.com/3CTRETQ4 (not completely blank, though... there are a few lines at the very left & top edge of the display)

A few seconds later, the display came back, and here's the dmesg right after that: http://pastebin.com/9mdfY5P1

Hm, there's nothing really interesting with that screen going on ... Also, 3.5.3 is up-to-date with all recent DP fixes. One thing that could be is that this is another version of our fdi link training woes on ivb.

To check for that, can you please run your 27" screen at a much lower resolution? If it still blanks out, it's a different issue.

Thanks, Daniel

Signature · 3 lines
Daniel Vetter
Mail: [email protected]
Mobile: +41 (0)79 365 57 48
#4 lore raw
Quoted 53 lines · Daniel Vetter
Quoted 43 lines · Chun-Yu Shei
Quoted 31 lines · Daniel Vetter
Quoted 30 lines · Chun-Yu Shei

Hi,

I recently upgraded to a 27" monitor (2560x1440) from a 23" one (1920x1080), and had to switch to Windows because the new monitor is unusable in Linux. Today, about a month later, I decided to give Linux another try, since there have been several updates to the Intel graphics driver since then.

Unfortunately, it seems that it's still unusable with xf86-video-intel 2.20.3 -- after a little while, the video signal to the 27" monitor completely stops, and it goes into power saving mode. I'm running dual monitors with the old 23", and that one continues running fine when this happens. This happens on my ThinkPad X220 (i5-2540M). The 27" is connected via DisplayPort, and the 23" via DVI. SNA is enabled, if it makes any difference (I haven't tried turning it off, but I probably should). This is the biggest problem I'm facing when it comes to Linux support.

I also gave the new "TearFree" option a try, and while it does a great job of eliminating tearing, it makes the two monitors become mirrors of each other for some reason. If I take a screenshot with the GNOME tool, the screenshot comes out as expected (unmirrored), but the video output on the two monitors is mirrored in reality. Disabling "TearFree" fixes this.

Also, when I'm using the ThinkPad's built-in display, it sometimes turns off for no apparent reason, although it's not too big of a deal since a suspend/resume cycle seems to fix things (and I haven't used 2.20.3 long enough to experience this yet).

Quoted 7 lines
Quoted 1 line

Any ideas/things I can do to help track these issues down?

For the screen blanking issues, the kernel is the important part. Please boot with drm.debug=0xe added to your kernel bootline and grab the full dmesg.
-Daniel

OK, I finally got around to doing this... I just upgraded to the 3.5.3 kernel and xf86-video-intel 2.20.5 as well.

Quoted 8 lines

Here's the initial dmesg upon bootup: http://pastebin.com/41F2AA0f

And here's the dmesg right after the 27" goes blank:
http://pastebin.com/3CTRETQ4 (not completely blank, though... there are a few lines at the very left & top edge of the display)

A few seconds later, the display came back, and here's the dmesg right after that: http://pastebin.com/9mdfY5P1

Quoted 9 lines

Hm, there's nothing really interesting with that screen going on ... Also, 3.5.3 is up-to-date with all recent DP fixes. One thing that could be is that this is another version of our fdi link training woes on ivb.

To check for that, can you please run your 27" screen at a much lower resolution? If it still blanks out, it's a different issue.

Thanks, Daniel

Seems to be working perfectly at 1600x900 (btw, I'm on Sandy Bridge, not ivb).

Chun-Yu

#5 lore raw
Quoted 58 lines · Chun-Yu Shei
Quoted 57 lines · Daniel Vetter
Quoted 43 lines · Chun-Yu Shei
Quoted 31 lines · Daniel Vetter
Quoted 30 lines · Chun-Yu Shei

Hi,

I recently upgraded to a 27" monitor (2560x1440) from a 23" one (1920x1080), and had to switch to Windows because the new monitor is unusable in Linux. Today, about a month later, I decided to give Linux another try, since there have been several updates to the Intel graphics driver since then.

Unfortunately, it seems that it's still unusable with xf86-video-intel 2.20.3 -- after a little while, the video signal to the 27" monitor completely stops, and it goes into power saving mode. I'm running dual monitors with the old 23", and that one continues running fine when this happens. This happens on my ThinkPad X220 (i5-2540M). The 27" is connected via DisplayPort, and the 23" via DVI. SNA is enabled, if it makes any difference (I haven't tried turning it off, but I probably should). This is the biggest problem I'm facing when it comes to Linux support.

I also gave the new "TearFree" option a try, and while it does a great job of eliminating tearing, it makes the two monitors become mirrors of each other for some reason. If I take a screenshot with the GNOME tool, the screenshot comes out as expected (unmirrored), but the video output on the two monitors is mirrored in reality. Disabling "TearFree" fixes this.

Also, when I'm using the ThinkPad's built-in display, it sometimes turns off for no apparent reason, although it's not too big of a deal since a suspend/resume cycle seems to fix things (and I haven't used 2.20.3 long enough to experience this yet).

Quoted 7 lines
Quoted 1 line

Any ideas/things I can do to help track these issues down?

For the screen blanking issues, the kernel is the important part. Please boot with drm.debug=0xe added to your kernel bootline and grab the full dmesg.
-Daniel

OK, I finally got around to doing this... I just upgraded to the 3.5.3 kernel and xf86-video-intel 2.20.5 as well.

Quoted 8 lines

Here's the initial dmesg upon bootup: http://pastebin.com/41F2AA0f

And here's the dmesg right after the 27" goes blank:
http://pastebin.com/3CTRETQ4 (not completely blank, though... there are a few lines at the very left & top edge of the display)

A few seconds later, the display came back, and here's the dmesg right after that: http://pastebin.com/9mdfY5P1

Hm, there's nothing really interesting with that screen going on ... Also, 3.5.3 is up-to-date with all recent DP fixes. One thing that could be is that this is another version of our fdi link training woes on ivb.

Quoted 8 lines
Quoted 5 lines

To check for that, can you please run your 27" screen at a much lower resolution? If it still blanks out, it's a different issue.

Thanks, Daniel

Seems to be working perfectly at 1600x900 (btw, I'm on Sandy Bridge, not ivb).

Hm ... I'm running low on ideas to try out then. Can you please file a bug report on bugs.freedesktop.org against drm/intel?

Thanks, Daniel

Signature · 3 lines
Daniel Vetter
Mail: [email protected]
Mobile: +41 (0)79 365 57 48
#6 lore raw
Quoted 65 lines · Daniel Vetter
Quoted 64 lines · Chun-Yu Shei
Quoted 62 lines · Daniel Vetter
Quoted 43 lines · Chun-Yu Shei
Quoted 31 lines · Daniel Vetter
Quoted 30 lines · Chun-Yu Shei

Hi,

I recently upgraded to a 27" monitor (2560x1440) from a 23" one (1920x1080), and had to switch to Windows because the new monitor is unusable in Linux. Today, about a month later, I decided to give Linux another try, since there have been several updates to the Intel graphics driver since then.

Unfortunately, it seems that it's still unusable with xf86-video-intel 2.20.3 -- after a little while, the video signal to the 27" monitor completely stops, and it goes into power saving mode. I'm running dual monitors with the old 23", and that one continues running fine when this happens. This happens on my ThinkPad X220 (i5-2540M). The 27" is connected via DisplayPort, and the 23" via DVI. SNA is enabled, if it makes any difference (I haven't tried turning it off, but I probably should). This is the biggest problem I'm facing when it comes to Linux support.

I also gave the new "TearFree" option a try, and while it does a great job of eliminating tearing, it makes the two monitors become mirrors of each other for some reason. If I take a screenshot with the GNOME tool, the screenshot comes out as expected (unmirrored), but the video output on the two monitors is mirrored in reality. Disabling "TearFree" fixes this.

Also, when I'm using the ThinkPad's built-in display, it sometimes turns off for no apparent reason, although it's not too big of a deal since a suspend/resume cycle seems to fix things (and I haven't used 2.20.3 long enough to experience this yet).

Quoted 7 lines
Quoted 1 line

Any ideas/things I can do to help track these issues down?

For the screen blanking issues, the kernel is the important part. Please boot with drm.debug=0xe added to your kernel bootline and grab the full dmesg.
-Daniel

OK, I finally got around to doing this... I just upgraded to the 3.5.3 kernel and xf86-video-intel 2.20.5 as well.

Quoted 8 lines

Here's the initial dmesg upon bootup: http://pastebin.com/41F2AA0f

And here's the dmesg right after the 27" goes blank:
http://pastebin.com/3CTRETQ4 (not completely blank, though... there are a few lines at the very left & top edge of the display)

A few seconds later, the display came back, and here's the dmesg right after that: http://pastebin.com/9mdfY5P1

Hm, there's nothing really interesting with that screen going on ... Also, 3.5.3 is up-to-date with all recent DP fixes. One thing that could be is that this is another version of our fdi link training woes on ivb.

To check for that, can you please run your 27" screen at a much lower resolution? If it still blanks out, it's a different issue.

Thanks, Daniel

Quoted 8 lines
Quoted 2 lines

Seems to be working perfectly at 1600x900 (btw, I'm on Sandy Bridge, not ivb).

Hm ... I'm running low on ideas to try out then. Can you please file a bug report on bugs.freedesktop.org against drm/intel?

Thanks, Daniel

Will do... I did a little more experimenting, and things seem to be fine at 1920x1440, but 2048x1152 starts to show the same screen blanking problem.

Chun-Yu