e1000e: Disabling IRQ #57 .. machine dies
Subsystems (2)
Hi:
In current linus tree, in a machine using the e1000e driver
hwinfo --netcard
22: PCI 400.0: 0200 Ethernet controller
[Created at pci.319]
Unique ID: rBUF.cuT2KaC3ZS1
Parent ID: HnsE.Z52SDLRIaH2
SysFS ID: /devices/pci0000:00/0000:00:1c.5/0000:04:00.0 SysFS BusID: 0000:04:00.0
Hardware Class: network
Model: "Intel 82574L Gigabit Network Connection"
Vendor: pci 0x8086 "Intel Corporation"
Device: pci 0x10d3 "82574L Gigabit Network Connection"
SubVendor: pci 0x1043 "ASUSTeK Computer Inc."
SubDevice: pci 0x8369
Driver: "e1000e"
Driver Modules: "e1000e"
Device File: eth0
Memory Range: 0xf7d00000-0xf7d1ffff (rw,non-prefetchable) I/O Ports: 0xd000-0xdfff (rw)
Memory Range: 0xf7d20000-0xf7d23fff (rw,non-prefetchable)
IRQ: 17 (no events)
Link detected: yes
Module Alias: "pci:v00008086d000010D3sv00001043sd00008369bc02sc00i00" Driver Info #0:
Driver Status: e1000e is active
Driver Activation Cmd: "modprobe e1000e"
Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #15 (PCI bridge)
cat /proc/interrupts
57 IR-PCI-MSI-edge eth0
the driver works after a while, but then a single message
"Disabling IRQ #57"
is sent to the console and the machine dies, nothing else is written in the logs and remote ikvm becames unresponsive so there is no way to bring more debug info back.. kernel 3.5.3 works ok.
Anyone else seeing this ?
Quoted 41 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Cristian Rodríguez
Sent: Tuesday, September 11, 2012 11:50 AM
To: Netdev
Subject: e1000e: Disabling IRQ #57 .. machine diesHi:
In current linus tree, in a machine using the e1000e driver
hwinfo --netcard
22: PCI 400.0: 0200 Ethernet controller
[Created at pci.319]
Unique ID: rBUF.cuT2KaC3ZS1
Parent ID: HnsE.Z52SDLRIaH2
SysFS ID: /devices/pci0000:00/0000:00:1c.5/0000:04:00.0 SysFS BusID: 0000:04:00.0
Hardware Class: network
Model: "Intel 82574L Gigabit Network Connection"
Vendor: pci0x8086"Intel Corporation"
Device: pci0x10d3"82574L Gigabit Network Connection"
SubVendor: pci0x1043"ASUSTeK Computer Inc."
SubDevice: pci0x8369
Driver: "e1000e"
Driver Modules: "e1000e"
Device File: eth0
Memory Range: 0xf7d00000-0xf7d1ffff (rw,non-prefetchable) I/O Ports: 0xd000-0xdfff (rw)
Memory Range: 0xf7d20000-0xf7d23fff (rw,non-prefetchable)
IRQ: 17 (no events)
Link detected: yes
Module Alias: "pci:v00008086d000010D3sv00001043sd00008369bc02sc00i00" Driver Info #0:
Driver Status: e1000e is active
Driver Activation Cmd: "modprobe e1000e"
Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #15 (PCI bridge)
Quoted 8 lines
cat
/proc/interrupts57 IR-PCI-MSI-edge eth0
the driver works after a while, but then a single message
"Disabling IRQ #57"
Hello,
I'm sorry you're having problems with out parts. Can you provide some more info on this issue? What version of the driver are you using? Is the only problem that this driver dies or are there other symptoms? What does the dmesg say for the e1000e driver at load? It usually list whether its using MSI/MSI-X, and some other info. Can you provide an lspci -vvv output for the 82574L device and the dmesg info? Is the "Disabling IRQ #57 message appearing in the dmesg log or somewhere else? Can you try loading the driver with the module parameter IntMode=0 to try the device in legacy interrupt mode, if its not already in that mode.
Thanks,
Carolyn
Carolyn Wyborny
Linux Development
LAN Access Division
Intel Corporation