execve and kernel_thread unification problem on m68knommu
Hi Al,
As of commit fea82210 ("m68k: switch to saner kernel_execve() semantics") I can't get non-mmu m68k targets to boot through to user space. I don't think this commit itself is the problem, but probably something in the generic execve changes.
What I see is that it boots up to trying to exec /bin/init and it tries to return back through an address of 0. Running on QEMU I see a final dump like this (full dump attached at end):
qemu: fatal: Trying to execute code outside RAM or ROM at 0x00000000
D0 = 00000000 A0 = 402e6090 F0 = 0000000000000000 ( 0) D1 = 00002000 A1 = 418bb400 F1 = 0000000000000000 ( 0) D2 = 418402f0 A2 = 4184c000 F2 = 0000000000000000 ( 0) D3 = 4184043a A3 = 40185fbc F3 = 0000000000000000 ( 0) D4 = 00000000 A4 = 00000000 F4 = 0000000000000000 ( 0) D5 = 00000000 A5 = 00000000 F5 = 0000000000000000 ( 0) D6 = 00000000 A6 = 00000000 F6 = 0000000000000000 ( 0) D7 = 00000000 A7 = 41837fc8 F7 = 0000000000000000 ( 0) PC = 00000000 SR = 2000 ----- FPRESULT = 0
Aborted
I haven't debugged this through yet. It was working back a few months ago when I tried these patches. Any ideas on what might be going wrong?
The little tracing I have done on it shows that we return back from do_execve() in init/main.c and back through to kernel_init(). The return there is the one that tries to go back through 0.
If I put the m68k arch ret_from_kernel_execve code back in entry.S and hack in a call to it from init/main.c run_init_process() then I can get it to fully boot, as it used to.
Regards
Greg
Linux version 3.8.0-rc5 (gerg@gumby) (gcc version 4.5.1 (GCC) ) #1 Sat
Jan 26 22:42:45 EST 2013
uClinux/COLDFIRE(m520x)
COLDFIRE port done by Greg Ungerer, [email protected]
Flat model support (C) 1998,1999 Kenneth Albanowski, D. Jeff Dionne Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4080 Kernel command line: root=/dev/mtdblock0
PID hash table entries: 128 (order: -4, 512 bytes)
Dentry cache hash table entries: 4096 (order: 1, 16384 bytes) Inode-cache hash table entries: 2048 (order: 0, 8192 bytes)
Memory: 29744k/29744k available (1448k kernel code, 1520k data, 56k init) Virtual kernel memory layout:
vector : 0x40000000 - 0x40000400 ( 1 KiB)
kmap : 0x00000000 - 0xffffffff (4095 MiB)
vmalloc : 0x00000000 - 0xffffffff (4095 MiB)
lowmem : 0x40000000 - 0x42000000 ( 32 MiB)
.init : 0x401c8000 - 0x401d6000 ( 56 KiB)
.text : 0x40020000 - 0x401889a0 (1443 KiB)
.data : 0x401889a0 - 0x401c7360 ( 251 KiB)
.bss : 0x401d6000 - 0x401e1a4c ( 47 KiB)SLUB: Genslabs=15, HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=8 NR_IRQS:256
Calibrating delay loop... 457.11 BogoMIPS (lpj=2285568)pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource pit
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 8192 bytes) TCP bind hash table entries: 1024 (order: -1, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 512 (order: 0, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 0, 8192 bytes)
NET: Registered protocol family 1
ROMFS MTD (C) 2007 Red Hat, Inc.
io scheduler noop registered (default)
ColdFire internal UART serial driver
ttyS0 at MMIO 0xfc060000 (irq = 90) is a ColdFire UART console [ttyS0] enabled
ttyS1 at MMIO 0xfc064000 (irq = 91) is a ColdFire UART
ttyS2 at MMIO 0xfc068000 (irq = 92) is a ColdFire UART
brd: module loaded
uclinux[mtd]: RAM probe address=0x401e1a4c size=0xde000 Creating 1 MTD partitions on "RAM":
0x000000000000-0x0000000de000 : "ROMfs"
FEC: MDIO read timeout
TCP: cubic registered
NET: Registered protocol family 17
VFS: Mounted root (romfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 56k freed (0x401c8000 - 0x401d6000)
qemu: fatal: Trying to execute code outside RAM or ROM at 0x00000000
D0 = 00000000 A0 = 402e6090 F0 = 0000000000000000 ( 0) D1 = 00002000 A1 = 418bb400 F1 = 0000000000000000 ( 0) D2 = 418402f0 A2 = 4184c000 F2 = 0000000000000000 ( 0) D3 = 4184043a A3 = 40185fbc F3 = 0000000000000000 ( 0) D4 = 00000000 A4 = 00000000 F4 = 0000000000000000 ( 0) D5 = 00000000 A5 = 00000000 F5 = 0000000000000000 ( 0) D6 = 00000000 A6 = 00000000 F6 = 0000000000000000 ( 0) D7 = 00000000 A7 = 41837fc8 F7 = 0000000000000000 ( 0) PC = 00000000 SR = 2000 ----- FPRESULT = 0
Aborted