Remounting UBI image leads to ECC errors
We have a custom made AM335x board I'm working on and I have encountered a problem when mounting an ubifs image from nand. If I ...
(1) Write an ubifs image to nand
(2) Mount the ubifs image
(3) Repeat step (2)
... this then corrupts the ubifs image.
Below is a full log.
Can anyone help ?
Regards
Mark J.
---
U-Boot SPL 2013.01-00336-g044fbc4-dirty (Feb 26 2013 - 14:07:36) U-Boot 2013.01-00336-g044fbc4-dirty (Feb 26 2013 - 14:07:36)
I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401000 using PIO, IRQ 0
Net: cpsw
U-Boot# nandecc hw 2
HW BCH8 selected
U-Boot# mw.b 82000000 ff 81f000
U-Boot# dhcp 82000000 10.0.0.100:/nanobone/rootfs.ubifs
link up on port 0, speed 100, full duplex
BOOTP broadcast 1
*** Unhandled DHCP Option in OFFER/ACK: 46
*** Unhandled DHCP Option in OFFER/ACK: 46
DHCP client bound to address 10.0.0.104
Using cpsw device
TFTP from server 10.0.0.100; our IP address is 10.0.0.104 Filename '/nanobone/rootfs.ubifs'.
Load address: 0x82000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################
657.2 KiB/sdone
Bytes transferred = 6029312 (5c0000 hex)
U-Boot# nand erase 200000 4000000
NAND erase: device 0 offset 0x200000, size 0x4000000 Erasing at 0x41e0000 -- 100% complete.
OK
U-Boot# nand write 82000000 200000 81f000
NAND write: device 0 offset 0x200000, size 0x81f000
8515584 bytes written: OK
U-Boot# nandecc hw 2
HW BCH8 selected
U-Boot# mtdparts default
U-Boot# ubi part rootfs
Creating 1 MTD partitions on "nand0":
0x000000200000-0x000004200000 : "mtd=6"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: volume 0 ("root") re-sized from 44 to 503 LEBs
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=6"
UBI: MTD device size: 64 MiB
UBI: number of good PEBs: 512
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 512
UBI: number of PEBs reserved for bad PEB handling: 5
UBI: max/mean erase counter: 1/0
U-Boot# nandecc hw 2
HW BCH8 selected
U-Boot# mtdparts default
U-Boot# ubi part rootfs
UBI: mtd1 is detached from ubi0
Creating 1 MTD partitions on "nand0":
0x000000200000-0x000004200000 : "mtd=6"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
ECC: uncorrectable.
ECC: uncorrectable.
UBI error: ubi_io_read: error -74 while reading 64 bytes from PEB 510:0, read 64 bytes
ECC: uncorrectable.
ECC: uncorrectable.
UBI error: ubi_io_read: error -74 while reading 512 bytes from PEB 510:512, read 512 bytes
ECC: uncorrectable.
ECC: uncorrectable.
UBI error: ubi_io_read: error -74 while reading 64 bytes from PEB 511:0, read 64 bytes
ECC: uncorrectable.
ECC: uncorrectable.
UBI error: ubi_io_read: error -74 while reading 512 bytes from PEB 511:512, read 512 bytes
ECC: uncorrectable.
ECC: uncorrectable.
Quoted 7 lines · Mark Jackson
We have a custom made AM335x board I'm working on and I have encountered a problem when mounting an ubifs image from nand. If I ...
(1) Write an ubifs image to nand
(2) Mount the ubifs image
(3) Repeat step (2)
Quoted 5 lines
... this then corrupts the ubifs image.
Below is a full log.
Can anyone help ?
Does anyone have any thoughts on this issue ?
Can someone confirm that they can repeat my test and it works / fails for them ?
Regards
Mark J.
Hi Mark,
Quoted 50 lines · Mark Jackson
We have a custom made AM335x board I'm working on and I have encountered a problem when mounting an ubifs image from nand. If I ...
(1) Write an ubifs image to nand
(2) Mount the ubifs image
(3) Repeat step (2)... this then corrupts the ubifs image.
Below is a full log.
Can anyone help ?
Regards
Mark J.
---
U-Boot SPL 2013.01-00336-g044fbc4-dirty (Feb 26 2013 - 14:07:36) U-Boot 2013.01-00336-g044fbc4-dirty (Feb 26 2013 - 14:07:36)I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memoryUSB Host mode controller at 47401000 using PIO, IRQ 0
Net: cpsw
U-Boot# nandecc hw 2
HW BCH8 selected
U-Boot# mw.b 82000000 ff 81f000
U-Boot# dhcp 82000000 10.0.0.100:/nanobone/rootfs.ubifs
link up on port 0, speed 100, full duplex
BOOTP broadcast 1
*** Unhandled DHCP Option in OFFER/ACK: 46
*** Unhandled DHCP Option in OFFER/ACK: 46
DHCP client bound to address 10.0.0.104
Using cpsw device
TFTP from server 10.0.0.100; our IP address is 10.0.0.104 Filename '/nanobone/rootfs.ubifs'.
Load address:0x82000000
Loading: ################################################################################################################################## ################################################################# ################################################################# ################################################################# ################################################################# ##################### 657.2 KiB/s
Quoted 8 lines
done
Bytes transferred = 6029312 (5c0000 hex)
U-Boot# nand erase 200000 4000000NAND erase: device 0 offset
0x200000, size0x4000000Erasing at0x41e0000-- 100% complete.
OK
U-Boot# nand write 82000000 200000 81f000
Please try to write with sub command trimffs. The command looks like nand write.trimffs 82000000 200000 81f000
If not has trimffs sub command, please add CONFIG_CMD_NAND_TRIMFFS into board configuration file.
Best Regards,
Bo Shen