MPC5121e, Linux, simple IO ports
Hello,
This is a simple board base on mpc5121e MCU.
Gpio is detected: kernel is compiled with its support - i gotgpiochip_find_base: found new base @224 in dmesg - on kernel 3.0.4.
But i'm unable to access it through /sys/class/gpio. I can successfully export a pin (ie, if i type cat 224 > export, gpio224 is created), but i can't successfully control it:
echo "out" > /sys/class/gpio/gpio224/direction
cat /sys/class/gpio/gpio224/value
0
echo 1 > /sys/class/gpio/gpio224/value
cat /sys/class/gpio/gpio224/value
0
My need is a simple chipselect (well, 3 chipselect exactly ), for a custom design. Running linux is mandatory. I suspect the MPC5121e to be in the bad function mode, so:
- does anyone knows how to change mode ? What register can i acces and how ? does it worths a try ?
- does anyone successfully performed simple IO control ?
Last thing, i have tryed to access internal registers through /dev/mem, but no success. There are very few ressources available for this microcontroler, but i'm stick to it. Perhaps anybody knows how to access (read) internal registers with /proc or sys-fs ?
Thank you for your help.
Sorry to bump the post, i'm wondering if it was correctly sent.
Quoted 54 lines · CF Studelec
Hello,
This is a simple board base on mpc5121e MCU.
Gpio is detected: kernel is compiled with its support - i got
gpiochip_find_base: found new base @224 in dmesg - on kernel 3.0.4.But i'm unable to access it through
/sys/class/gpio. I can successfully export a pin (ie, if i type cat 224 > export, gpio224 is created), but i can't successfully control it:echo "out" >
/sys/class/gpio/gpio224/directioncat
/sys/class/gpio/gpio224/value0
echo 1 >
/sys/class/gpio/gpio224/valuecat
/sys/class/gpio/gpio224/value0
My need is a simple chipselect (well, 3 chipselect exactly ), for a custom design. Running linux is mandatory. I suspect the MPC5121e to be in the bad function mode, so:
- does anyone knows how to change mode ? What register can i acces and how ? does it worths a try ?
- does anyone successfully performed simple IO control ?
Last thing, i have tryed to access internal registers through
/dev/mem, but no success. There are very few ressources available for this microcontroler, but i'm stick to it. Perhaps anybody knows how to access (read) internal registers with /proc or sys-fs ?Thank you for your help.
_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://lists.ozlabs.org/listinfo/linuxppc-dev
Hello,
Quoted 25 lines · On Thu, 21 Mar 2013 09:54:46 +0100 CF Studelec <[email protected]> wrote:
Hello,
This is a simple board base on mpc5121e MCU.
Gpio is detected: kernel is compiled with its support - i got
gpiochip_find_base: found new base @224 in dmesg - on kernel 3.0.4.But i'm unable to access it through
/sys/class/gpio. I can successfully export a pin (ie, if i type cat 224 > export, gpio224 is created), but i can't successfully control it:echo "out" >
/sys/class/gpio/gpio224/directioncat
/sys/class/gpio/gpio224/value0
echo 1 >
/sys/class/gpio/gpio224/valuecat
/sys/class/gpio/gpio224/value
Quoted 8 lines
0
My need is a simple chipselect (well, 3 chipselect exactly ), for a custom design. Running linux is mandatory. I suspect the MPC5121e to be in the bad function mode, so:
- does anyone knows how to change mode ? What register can i acces and how ? does it worths a try ?
For GPIO0 - GPIO7 pins you additionally need to configure the pin mux for GPIO mode, see IO_CONTROL_GP register description in the manual.
Quoted 1 line
- does anyone successfully performed simple IO control ?
We use it all the time, i.e. as SD-Card detect and/or write-protect GPIOs, as SPI Chips-Select GPIOs, etc. It works.
Quoted 4 lines
Last thing, i have tryed to access internal registers through
/dev/mem, but no success. There are very few ressources available for this microcontroler, but i'm stick to it. Perhaps anybody knows how to access (read) internal registers with /proc or sys-fs ?
Accessing registers using /dev/mem should work (tested using devmem2.c tool with recent v3.9-rc4 kernel. Should work with older kernels too).
Alternatively (as a quick test) you could configure the registers under U-Boot using "mw" command, assuming you are using U-Boot as a bootloader.
HTH,
Anatolij
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: [email protected]