Skip to contentSkip to conversation

How do I use AM335x eth1 rather than eth0 ?

U-Boot Mark Jackson 3 participants 4 messages Apr 12, 2013 – Apr 20, 2013

lore
Share & tools
lore
#0 lore raw

We have a dual Ethernet board (based on the BeagelBone) but with both Ethernet ports connected.

I'm wanting to use eth1 (rather than eth0), so in my board.c file, I changed:-

static struct cpsw_slave_data cpsw_slaves[] = {
	{
		.slave_reg_ofs	= 0x208,
		.sliver_reg_ofs	= 0xd80,
		.phy_id		= 0,
	},
	{
		.slave_reg_ofs	= 0x308,
		.sliver_reg_ofs	= 0xdc0,
		.phy_id		= 1,
	},
};

... to ...

static struct cpsw_slave_data cpsw_slaves[] = {
	{
		.slave_reg_ofs	= 0x308,
		.sliver_reg_ofs	= 0xdc0,
		.phy_id		= 1,
	},
	{
		.slave_reg_ofs	= 0x208,
		.sliver_reg_ofs	= 0xd80,
		.phy_id		= 0,
	},
};

... assuming that eth0 would now be ignored (as only 1 slave is configured).

But (eg) dhcp still only responds on eth0 !?!

What else do I have to change ?

Cheers
Mark J.

#1 lore raw

Hi Mark,

Quoted 32 lines · Mark Jackson

We have a dual Ethernet board (based on the BeagelBone) but with both Ethernet ports connected.

I'm wanting to use eth1 (rather than eth0), so in my board.c file, I changed:-

static struct cpsw_slave_data cpsw_slaves[] = {
	{
		.slave_reg_ofs	= 0x208,
		.sliver_reg_ofs	= 0xd80,
		.phy_id		= 0,
	},
	{
		.slave_reg_ofs	= 0x308,
		.sliver_reg_ofs	= 0xdc0,
		.phy_id		= 1,
	},
};

... to ...

static struct cpsw_slave_data cpsw_slaves[] = {
	{
		.slave_reg_ofs	= 0x308,
		.sliver_reg_ofs	= 0xdc0,
		.phy_id		= 1,
	},
	{
		.slave_reg_ofs	= 0x208,
		.sliver_reg_ofs	= 0xd80,
		.phy_id		= 0,
	},
};
Quoted 5 lines

... assuming that eth0 would now be ignored (as only 1 slave is configured).

But (eg) dhcp still only responds on eth0 !?!

What else do I have to change ?

Have you try "setenv ethprime eth1"? Then reset board, and do dhcp.

Best Regards,
Bo Shen

Quoted 7 lines

Cheers
Mark J.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#2 lore raw

Dear Bo Shen,

Quoted 4 lines · In message <[email protected]> you wrote:
Quoted 2 lines

What else do I have to change ?

Have you try "setenv ethprime eth1"? Then reset board, and do dhcp.

Before thje reset, doi also a "saveenv" to make the setting stick.

Or "setenv ethact eth1" and retry then (without reset).

Best regards,

Wolfgang Denk

Signature · 3 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
#3 lore raw

Hi Wolfgang,

Quoted 8 lines · Wolfgang Denk

Dear Bo Shen,

Quoted 2 lines · In message <[email protected]> you wrote:
Quoted 1 line

What else do I have to change ?

Have you try "setenv ethprime eth1"? Then reset board, and do dhcp.

Before thje reset, doi also a "saveenv" to make the setting stick.

Or "setenv ethact eth1" and retry then (without reset).

Thanks for you information, without reset is better.

Best Regards,
Bo Shen

Quoted 5 lines

Best regards,

Wolfgang Denk