Dell U2412M monitor complains about input timing
Hi all,
I hope I have found the right forum for asking my question -- apologies if that's not the case. I have a Dell U2412M connected to a Dell StudioSlim 540s, with the i915 driver on Fedora's 3.9.6 Kernel running KDE (4.10.4). The monitor is connected via an HDMI cable, with a DVI adapter to the monitor. When booting up my machine into X or waking it from sleep, things work perfectly. However, when I turn off the monitor (or whenever it turns itself off, if configured to do so) while the PC keeps running, I have a hard time getting the monitor to work when turning it on again. One of three things happens:
(1) The monitor pops up a message saying that "The current input timing is not supported by the monitor display. Please change your input to 1920x1200@60Hz".
(2) The expected desktop contents appear on screen, but only for a fraction of a second. Then the monitor goes blank again for a few seconds, and this iterates until I turn it off again.
(3) Things work as expected, but unfortunately only after turning the monitor on and off on the order of a dozen times. Even then, the configuration is a bit wonky (for example, xrandr shows all connections disconnected).
I have the monitor configured to 1920x1200@60Hz both in KDE's settings and via variations of an xorg.conf (including no xorg.conf) in which I expressly state that this is what my monitor needs.
I'm wondering if the problem might be HDMI-related and whether it sounds familiar to folks on this list. Any help is welcome.
Cheers,
Christian
Quoted 25 lines · On Mon, 08 Jul 2013 21:38:13 -0700 Christian Kreibich <[email protected]>…
Hi all,
I hope I have found the right forum for asking my question -- apologies if that's not the case. I have a Dell U2412M connected to a Dell StudioSlim 540s, with the i915 driver on Fedora's 3.9.6 Kernel running KDE (4.10.4). The monitor is connected via an HDMI cable, with a DVI adapter to the monitor. When booting up my machine into X or waking it from sleep, things work perfectly. However, when I turn off the monitor (or whenever it turns itself off, if configured to do so) while the PC keeps running, I have a hard time getting the monitor to work when turning it on again. One of three things happens:
(1) The monitor pops up a message saying that "The current input timing is not supported by the monitor display. Please change your input to 1920x1200@60Hz".
(2) The expected desktop contents appear on screen, but only for a fraction of a second. Then the monitor goes blank again for a few seconds, and this iterates until I turn it off again.
(3) Things work as expected, but unfortunately only after turning the monitor on and off on the order of a dozen times. Even then, the configuration is a bit wonky (for example, xrandr shows all connections disconnected).
Quoted 6 lines
I have the monitor configured to 1920x1200@60Hz both in KDE's settings and via variations of an xorg.conf (including no xorg.conf) in which I expressly state that this is what my monitor needs.
I'm wondering if the problem might be HDMI-related and whether it sounds familiar to folks on this list. Any help is welcome.
Sounds like our pixel clock is probably out of the range your monitor wants. If you can get that mode running with the VESA driver you could collect a register dump in the good and bad cases so we could compare...
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
Quoted 3 lines · Jesse Barnes
Sounds like our pixel clock is probably out of the range your monitor wants. If you can get that mode running with the VESA driver you could collect a register dump in the good and bad cases so we could compare...
I'm very happy to try (though it'll have to wait ~2 weeks as I'm on travel). Can you point me at the right command for collecting the register dump?
-C.
Quoted 8 lines · On Tue, 09 Jul 2013 14:46:28 -0700 Christian Kreibich <[email protected]>…
Quoted 3 lines · Jesse Barnes
Sounds like our pixel clock is probably out of the range your monitor wants. If you can get that mode running with the VESA driver you could collect a register dump in the good and bad cases so we could compare...
I'm very happy to try (though it'll have to wait ~2 weeks as I'm on travel). Can you point me at the right command for collecting the register dump?
You can use intel_reg_dumper or quick_dump from intel-gpu-tools. Hopefully your distro has it packaged, otherwise you can build the version at git.freedesktop.org/git/xorg/app/intel-gpu-tools.
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
Quoted 3 lines · Jesse Barnes
You can use
intel_reg_dumperorquick_dumpfrom intel-gpu-tools. Hopefully your distro has it packaged, otherwise you can build the version at git.freedesktop.org/git/xorg/app/intel-gpu-tools.
Great, thx! I'll follow up once I've had a chance to try this out.
-C.
Fyi, it turns out that replacing the HDMI cable + DVI adapter fixed the problem. Sorry for the noise.
-C.