Skip to contentSkip to conversation

Switching band of a dual-band WiFi device

DISCUSSION Christian Gagneraud 2 participants 4 messages Aug 15, 2013 1 message not in the archive

lore
Share & tools
lore
#0 lore raw

Hi there,

I am using a TP-Link TL-WDN3200 on a ubuntu 13.04 (kernel 3.8.0-27-generic), and I have install relevant modules with backports-3.11-rc3-1.

I would like to switch my WiFi stick to 5GHz, I tried iwconfig wlan0 freq 5G, but I get ENOTSUPP.
Is the freq settings suppose to handle this 2.4 vs 5GHz band or is it only for selecting channel frequency within a given band?

Does linux-wireless provides a way for selecting 2.4 or 5GHz band?

"iw phy phy11 info" tells me that in band 2, all the frequencies are disabled except:
* 5745 MHz [149] (30.0 dBm)
* 5755 MHz [151] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5775 MHz [155] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5795 MHz [159] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)

As well, my understanding of WiFi might be a bit limited but, does a dual-band WiFi device provides 2.4 and 5GHz services at the same time or do I need to select one or the other myself? Or maybe I can just enable/disable them manually (and separately)?

Hope someone can shed some light at this.

Regards,
Chris

#2 lore raw
In reply to a message not in the archive
Quoted 3 lines · Siyu Qiu

hi, do you mean that you take the wireless card from tplink and embed it into your pc ? Does it work ? Coz i want to put qca 9889 into pc but the info about network controller is :!!! unknown type 7f

Hi Siyu Qio,

I'm not sure to understand your question, but this is what I did
- went to the shop to buy this USB stick
- plugged it in a USB slot of my PC

And now I'm trying to understand if I can switch/enable/disable these 2 bands, and more importantly, do I really need to? Right now, my feeling is that "it just works out of the box", I shouldn't try to do this kind of things. I just try to understand this dual-band thing.

Chris

PS: Can you reply on the mailing list instead of sending private email please?

Quoted 45 lines

On Aug 14, 2013 10:12 PM, "Christian Gagneraud" <[email protected] <mailto:[email protected]>> wrote:

Hi there,

I am using a TP-Link TL-WDN3200 on a ubuntu 13.04 (kernel 3.8.0-27-generic), and I have install relevant modules with backports-3.11-rc3-1.

I would like to switch my WiFi stick to 5GHz, I tried iwconfig wlan0 freq 5G, but I get ENOTSUPP.
Is the freq settings suppose to handle this 2.4 vs 5GHz band or is it only for selecting channel frequency within a given band?

Does linux-wireless provides a way for selecting 2.4 or 5GHz band?

"iw phy phy11 info" tells me that in band 2, all the frequencies are disabled except:
* 5745 MHz [149] (30.0 dBm)
* 5755 MHz [151] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5775 MHz [155] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5795 MHz [159] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)

As well, my understanding of WiFi might be a bit limited but, does a dual-band WiFi device provides 2.4 and 5GHz services at the same time or do I need to select one or the other myself? Or maybe I can just enable/disable them manually (and separately)?

Hope someone can shed some light at this.

Regards,
Chris
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to [email protected] <mailto:[email protected]>
More majordomo info at http://vger.kernel.org/__majordomo-info.html
<http://vger.kernel.org/majordomo-info.html>

#3 lore raw
In reply to Christian Gagneraud
Quoted 6 lines · On Thursday 15 August 2013 17:11:59 Christian Gagneraud wrote:

Hi there,

I am using a TP-Link TL-WDN3200 on a ubuntu 13.04 (kernel 3.8.0-27-generic), and I have install relevant modules with backports-3.11-rc3-1.

Quoted 6 lines

I would like to switch my WiFi stick to 5GHz, I tried iwconfig wlan0 freq 5G, but I get ENOTSUPP.
Is the freq settings suppose to handle this 2.4 vs 5GHz band or is it only for selecting channel frequency within a given band?

Does linux-wireless provides a way for selecting 2.4 or 5GHz band?

Linux should automatically select the right frequency band, depending on the frequencies in use by the device you're trying to communicate with. Connect to an AP in the 5GHz band, and Linux should just use 5GHz automatically.

Quoted 12 lines

"iw phy phy11 info" tells me that in band 2, all the frequencies are disabled except:
* 5745 MHz [149] (30.0 dBm)
* 5755 MHz [151] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5775 MHz [155] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5795 MHz [159] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)

That's showing you that, with Linux's understanding of the RF regulations in your area, it can only transmit on certain frequencies.

Quoted 5 lines

As well, my understanding of WiFi might be a bit limited but, does a dual-band WiFi device provides 2.4 and 5GHz services at the same time or do I need to select one or the other myself? Or maybe I can just enable/disable them manually (and separately)?

A dual-band WiFi device can only transmit and receive on one channel at a time. The advantage of dual-band is that it can transmit and receive on either the 5GHz band (which is less crowded), or the 2.4GHz band (which is more commonly used). There's no need to select the band manually - it will just use 5GHz when the other device (e.g. the AP) is using 5GHz.

Signature · 4 lines
Simon Farnsworth
Software Engineer
ONELAN Ltd
http://www.onelan.com
#4 lore raw
Quoted 30 lines · Simon Farnsworth
Quoted 6 lines · On Thursday 15 August 2013 17:11:59 Christian Gagneraud wrote:

Hi there,

I am using a TP-Link TL-WDN3200 on a ubuntu 13.04 (kernel 3.8.0-27-generic), and I have install relevant modules with backports-3.11-rc3-1.

Quoted 6 lines

I would like to switch my WiFi stick to 5GHz, I tried iwconfig wlan0 freq 5G, but I get ENOTSUPP.
Is the freq settings suppose to handle this 2.4 vs 5GHz band or is it only for selecting channel frequency within a given band?

Does linux-wireless provides a way for selecting 2.4 or 5GHz band?

Linux should automatically select the right frequency band, depending on the frequencies in use by the device you're trying to communicate with. Connect to an AP in the 5GHz band, and Linux should just use 5GHz automatically.

Quoted 12 lines

"iw phy phy11 info" tells me that in band 2, all the frequencies are disabled except:
* 5745 MHz [149] (30.0 dBm)
* 5755 MHz [151] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5775 MHz [155] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5795 MHz [159] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)

Quoted 2 lines

That's showing you that, with Linux's understanding of the RF regulations in your area, it can only transmit on certain frequencies.

OK, that's the CRDA thing, I understand now! ;)

Quoted 6 lines
Quoted 6 lines

As well, my understanding of WiFi might be a bit limited but, does a dual-band WiFi device provides 2.4 and 5GHz services at the same time or do I need to select one or the other myself? Or maybe I can just enable/disable them manually (and separately)?

Quoted 6 lines

A dual-band WiFi device can only transmit and receive on one channel at a time. The advantage of dual-band is that it can transmit and receive on either the 5GHz band (which is less crowded), or the 2.4GHz band (which is more commonly used). There's no need to select the band manually - it will just use 5GHz when the other device (e.g. the AP) is using 5GHz.

Thanks for your answers Simon, everything is working now.
I had to change the regulatory domain of the USB stick to NZ as it comes with CN (country of origin) and NZ/CN don't really overlap in the 5GHz band.

Regards,
Chris