Skip to contentSkip to conversation

pm80xx: IButton feature support and Indirect SMP fix.

PATCH Superseded Anand 2 participants 2 messages Sep 16, 2013

Subsystems (2)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Anand

author
#0 lore raw

PATCH 2/5 pm80xx: IButton feature support and Indirect SMP fix.

Quoted 1 line

From db345f70bef0b07655d887f2d0398faf666f4a48 Mon Sep 17 00:00:00 2001

From: Anand Kumar Santhanam <[email protected]>
Date: Tue, 3 Sep 2013 15:21:29 +0530
Subject: [PATCH 2/5] pm80xx: IButton feature support and Indirect SMP fix.

IButton security feature support for motherboard controllers. Fix for indirect data transfer mode in case of SMP request.

Signed-off-by [email protected]
---
 drivers/scsi/pm8001/pm80xx_hwi.c |   26 ++++++++++++++++++++++----
 1 files changed, 22 insertions(+), 4 deletions(-)
drivers/scsi/pm8001/pm80xx_hwi.c +22 -4
index be0b394..158e91d 100644
@@ -967,6 +967,7 @@ pm80xx_chip_soft_rst(struct pm8001_hba_info *pm8001_ha)
 {
 	u32 regval;
 	u32 bootloader_state;
+	u32 ibutton0, ibutton1;
 
 	/* Check if MPI is in ready state to reset */
 	if (mpi_uninit_check(pm8001_ha) != 0) {
@@ -1025,7 +1026,26 @@ pm80xx_chip_soft_rst(struct pm8001_hba_info *pm8001_ha)
 	if (-1 == check_fw_ready(pm8001_ha)) {
 		PM8001_FAIL_DBG(pm8001_ha,
 			pm8001_printk("Firmware is not ready!\n"));
-		return -EBUSY;
+		/* check iButton feature support for motherboard controller */
+		if (pm8001_ha->pdev->subsystem_vendor !=
+			PCI_VENDOR_ID_ADAPTEC2) {
+			ibutton0 = pm8001_cr32(pm8001_ha, 0,
+					MSGU_HOST_SCRATCH_PAD_6);
+			ibutton1 = pm8001_cr32(pm8001_ha, 0,
+					MSGU_HOST_SCRATCH_PAD_7);
+			if (!ibutton0 && !ibutton1) {
+				PM8001_FAIL_DBG(pm8001_ha,
+					pm8001_printk("iButton Feature is"
+					" not Available!!!\n"));
+				return -EBUSY;
+			}
+			if (ibutton0 == 0xdeadbeef && ibutton1 == 0xdeadbeef) {
+				PM8001_FAIL_DBG(pm8001_ha,
+					pm8001_printk("CRC Check for iButton"
+					" Feature Failed!!!\n"));
+				return -EBUSY;
+			}
+		}
 	}
 	PM8001_INIT_DBG(pm8001_ha,
 		pm8001_printk("SPCv soft reset Complete\n"));
@@ -3492,8 +3512,6 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
 	else
 		pm8001_ha->smp_exp_mode = SMP_INDIRECT;
 
-	/* DIRECT MODE support only in spcv/ve */
-	pm8001_ha->smp_exp_mode = SMP_DIRECT;
 
 	tmp_addr = cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req));
 	preq_dma_addr = (char *)phys_to_virt(tmp_addr);
@@ -3509,7 +3527,7 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
 		/* exclude top 4 bytes for SMP req header */
 		smp_cmd.long_smp_req.long_req_addr =
 			cpu_to_le64((u64)sg_dma_address
-				(&task->smp_task.smp_req) - 4);
+				(&task->smp_task.smp_req) + 4);
 		/* exclude 4 bytes for SMP req header and CRC */
 		smp_cmd.long_smp_req.long_req_size =
 			cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_req)-8);
Signature · 1 line
1.7.1
#1 lore raw
Quoted 8 lines · Anand

From db345f70bef0b07655d887f2d0398faf666f4a48 Mon Sep 17 00:00:00 2001
From: Anand Kumar Santhanam <[email protected]>
Date: Tue, 3 Sep 2013 15:21:29 +0530
Subject: [PATCH 2/5] pm80xx: IButton feature support and Indirect SMP fix.

IButton security feature support for motherboard controllers. Fix for indirect data transfer mode in case of SMP request.

You'd better split this into two patches for bisect-able.

Jack

Quoted 65 lines
Signed-off-by [email protected]
---
 drivers/scsi/pm8001/pm80xx_hwi.c |   26 ++++++++++++++++++++++----
 1 files changed, 22 insertions(+), 4 deletions(-)
drivers/scsi/pm8001/pm80xx_hwi.c +22 -4
index be0b394..158e91d 100644
@@ -967,6 +967,7 @@ pm80xx_chip_soft_rst(struct pm8001_hba_info *pm8001_ha)
 {
 	u32 regval;
 	u32 bootloader_state;
+	u32 ibutton0, ibutton1;
 
 	/* Check if MPI is in ready state to reset */
 	if (mpi_uninit_check(pm8001_ha) != 0) {
@@ -1025,7 +1026,26 @@ pm80xx_chip_soft_rst(struct pm8001_hba_info *pm8001_ha)
 	if (-1 == check_fw_ready(pm8001_ha)) {
 		PM8001_FAIL_DBG(pm8001_ha,
 			pm8001_printk("Firmware is not ready!\n"));
-		return -EBUSY;
+		/* check iButton feature support for motherboard controller */
+		if (pm8001_ha->pdev->subsystem_vendor !=
+			PCI_VENDOR_ID_ADAPTEC2) {
+			ibutton0 = pm8001_cr32(pm8001_ha, 0,
+					MSGU_HOST_SCRATCH_PAD_6);
+			ibutton1 = pm8001_cr32(pm8001_ha, 0,
+					MSGU_HOST_SCRATCH_PAD_7);
+			if (!ibutton0 && !ibutton1) {
+				PM8001_FAIL_DBG(pm8001_ha,
+					pm8001_printk("iButton Feature is"
+					" not Available!!!\n"));
+				return -EBUSY;
+			}
+			if (ibutton0 == 0xdeadbeef && ibutton1 == 0xdeadbeef) {
+				PM8001_FAIL_DBG(pm8001_ha,
+					pm8001_printk("CRC Check for iButton"
+					" Feature Failed!!!\n"));
+				return -EBUSY;
+			}
+		}
 	}
 	PM8001_INIT_DBG(pm8001_ha,
 		pm8001_printk("SPCv soft reset Complete\n"));
@@ -3492,8 +3512,6 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
 	else
 		pm8001_ha->smp_exp_mode = SMP_INDIRECT;
 
-	/* DIRECT MODE support only in spcv/ve */
-	pm8001_ha->smp_exp_mode = SMP_DIRECT;
 
 	tmp_addr = cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req));
 	preq_dma_addr = (char *)phys_to_virt(tmp_addr);
@@ -3509,7 +3527,7 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
 		/* exclude top 4 bytes for SMP req header */
 		smp_cmd.long_smp_req.long_req_addr =
 			cpu_to_le64((u64)sg_dma_address
-				(&task->smp_task.smp_req) - 4);
+				(&task->smp_task.smp_req) + 4);
 		/* exclude 4 bytes for SMP req header and CRC */
 		smp_cmd.long_smp_req.long_req_size =
 			cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_req)-8);