Skip to contentSkip to conversation

AM335x BeagleBone Buffer XRUN

3.13-rc8 Jack Mitchell 1 participant 2 messages Jan 14, 2014 – Jan 16, 2014

lore
Share & tools
lore
#0 lore raw

I am currently trying to debug a buffer overrun when capturing with the BeagleBone Black and Audio Cape attached on 3.13-rc8, this is pretty much the same setup as the am335x-evm. The following is the traceback captured using the XRUN_BUFFER_DEBUG kernel config option. I think an interrupt is taking too long to return.

Example Traceback 1 (Writing to uSD card)

Quoted 15 lines
[  802.578728] ALSA sound/core/pcm_lib.c:177 XRUN: pcmC0D0c:0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.13.0-rc8-00005-ga6da83f-dirty #12
[  802.593139] [<c00160e8>] (unwind_backtrace+0x0/0x12c) from [<c0012b08>] (show_stack+0x10/0x14)
[  802.602174] [<c0012b08>] (show_stack+0x10/0x14) from [<c058c80c>] (dump_stack+0x7c/0x94)
[  802.610659] [<c058c80c>] (dump_stack+0x7c/0x94) from [<c04862e8>] (xrun+0x80/0xb0)
[  802.618596] [<c04862e8>] (xrun+0x80/0xb0) from [<c0486e1c>] (snd_pcm_update_state+0xf8/0x100)
[  802.627531] [<c0486e1c>] (snd_pcm_update_state+0xf8/0x100) from [<c0487048>] (snd_pcm_update_hw_ptr0+0x224/0x82c)
[  802.638281] [<c0487048>] (snd_pcm_update_hw_ptr0+0x224/0x82c) from [<c0487700>] (snd_pcm_period_elapsed+0xb0/0xf4)
[  802.649131] [<c0487700>] (snd_pcm_period_elapsed+0xb0/0xf4) from [<c0021458>] (dma_irq_handler+0x130/0x1f4)
[  802.659345] [<c0021458>] (dma_irq_handler+0x130/0x1f4) from [<c008e504>] (handle_irq_event_percpu+0x5c/0x21c)
[  802.669735] [<c008e504>] (handle_irq_event_percpu+0x5c/0x21c) from [<c008e700>] (handle_irq_event+0x3c/0x5c)
[  802.680035] [<c008e700>] (handle_irq_event+0x3c/0x5c) from [<c0091038>] (handle_level_irq+0xac/0x118)
[  802.689697] [<c0091038>] (handle_level_irq+0xac/0x118) from [<c008dc8c>] (generic_handle_irq+0x28/0x3c)
[  802.699542] [<c008dc8c>] (generic_handle_irq+0x28/0x3c) from [<c000f968>] (handle_IRQ+0x4c/0xb4)
[  802.708750] [<c000f968>] (handle_IRQ+0x4c/0xb4) from [<c00085b4>] (omap3_intc_handle_irq+0x60/0x74)
Quoted 8 lines
[  802.718237] [<c00085b4>] (omap3_intc_handle_irq+0x60/0x74) from [<c0592a64>] (__irq_svc+0x44/0x5c)
[  802.727618] Exception stack(0xc088df58 to 0xc088dfa0)
[  802.732912] df40:                                                       00000001 00000001
[  802.741479] df60: 00000000 c0897cb0 c088c000 c088c000 00000000 c0933bd4 c08949a0 c0894880
[  802.750047] df80: c0894930 c059f4a8 c088c020 c088dfa0 c0082ef8 c000fd00 20070013 ffffffff
[  802.758620] [<c0592a64>] (__irq_svc+0x44/0x5c) from [<c000fd00>] (arch_cpu_idle+0x20/0x3c)
[  802.767283] [<c000fd00>] (arch_cpu_idle+0x20/0x3c) from [<c008db84>] (cpu_startup_entry+0x120/0x1f0)
[  802.776858] [<c008db84>] (cpu_startup_entry+0x120/0x1f0) from [<c0826a9c>] (start_kernel+0x304/0x364)

Example Traceback 2 (Writing to tmpfs)

Quoted 21 lines
[ 1310.025256] ALSA sound/core/pcm_lib.c:177 XRUN: pcmC0D0c:0
[ 1310.031046] CPU: 0 PID: 998 Comm: avconv Not tainted 3.13.0-rc8-00005-ga6da83f-dirty #12
[ 1310.039580] [<c00160e8>] (unwind_backtrace+0x0/0x12c) from [<c0012b08>] (show_stack+0x10/0x14)
[ 1310.048615] [<c0012b08>] (show_stack+0x10/0x14) from [<c058c80c>] (dump_stack+0x7c/0x94)
[ 1310.057102] [<c058c80c>] (dump_stack+0x7c/0x94) from [<c04862e8>] (xrun+0x80/0xb0)
1310.065039] [<c04862e8>] (xrun+0x80/0xb0) from [<c0486e1c>] (snd_pcm_update_state+0xf8/0x100)
[ 1310.073974] [<c0486e1c>] (snd_pcm_update_state+0xf8/0x100) from [<c0487048>] (snd_pcm_update_hw_ptr0+0x224/0x82c)
[ 1310.084724] [<c0487048>] (snd_pcm_update_hw_ptr0+0x224/0x82c) from [<c0487700>] (snd_pcm_period_elapsed+0xb0/0xf4)
[ 1310.095574] [<c0487700>] (snd_pcm_period_elapsed+0xb0/0xf4) from [<c0021458>] (dma_irq_handler+0x130/0x1f4)
[ 1310.105788] [<c0021458>] (dma_irq_handler+0x130/0x1f4) from [<c008e504>] (handle_irq_event_percpu+0x5c/0x21c)
[ 1310.116178] [<c008e504>] (handle_irq_event_percpu+0x5c/0x21c) from [<c008e700>] (handle_irq_event+0x3c/0x5c)
[ 1310.126477] [<c008e700>] (handle_irq_event+0x3c/0x5c) from [<c0091038>] (handle_level_irq+0xac/0x118)
[ 1310.136138] [<c0091038>] (handle_level_irq+0xac/0x118) from [<c008dc8c>] (generic_handle_irq+0x28/0x3c)
[ 1310.145982] [<c008dc8c>] (generic_handle_irq+0x28/0x3c) from [<c000f968>] (handle_IRQ+0x4c/0xb4)
[ 1310.155190] [<c000f968>] (handle_IRQ+0x4c/0xb4) from [<c00085b4>] (omap3_intc_handle_irq+0x60/0x74)
[ 1310.164677] [<c00085b4>] (omap3_intc_handle_irq+0x60/0x74) from [<c0592a64>] (__irq_svc+0x44/0x5c)
[ 1310.174056] Exception stack(0xde0f7ee0 to 0xde0f7f28)
[ 1310.179354] 7ee0: 00000001 00000000 00000000 de3f8a80 00000000 00000002 c0047968 00000054
[ 1310.187920] 7f00: 00000000 b5440c64 c0933670 beb92fb8 de0f6028 de0f7f28 c0082eb0 c0047348
[ 1310.196480] 7f20: 60000113 ffffffff
[ 1310.200153] [<c0592a64>] (__irq_svc+0x44/0x5c) from [<c0047348>] (__do_softirq+0xa8/0x2f4)
Quoted 8 lines
[ 1310.208817] [<c0047348>] (__do_softirq+0xa8/0x2f4) from [<c0047968>] (irq_exit+0xac/0x104)
[ 1310.217479] [<c0047968>] (irq_exit+0xac/0x104) from [<c000f970>] (handle_IRQ+0x54/0xb4)
[ 1310.225868] [<c000f970>] (handle_IRQ+0x54/0xb4) from [<c00085b4>] (omap3_intc_handle_irq+0x60/0x74)
[ 1310.235347] [<c00085b4>] (omap3_intc_handle_irq+0x60/0x74) from [<c0592c3c>] (__irq_usr+0x3c/0x60)
[ 1310.244724] Exception stack(0xde0f7fb0 to 0xde0f7ff8)
[ 1310.250019] 7fa0:                                     beb94588 beb92ab8 beb9301c beb93038
[ 1310.258586] 7fc0: 00088ca0 00000140 00000160 b5440f18 00000080 b5440c64 beb92ab8 beb92fb8
[ 1310.267150] 7fe0: 4b000001 beb9267c b5f4d6a0 b5f4c8c8 80000010 ffffffff

I have done some tests and capturing to a uSD card is the easiest way to trigger XRUNS, where they occur often. Capturing to the eMMC is a little bit better. Capturing directly to tmpfs is nearly perfect, apart from very rare XRUN occurrences (10 minutes average maybe). This makes sense as EDMA is used to perform writes to the uSD and eMMC devices, so if they're being hogged with writes, then there is no time to transfer out the sound buffer and we get an overrun.

So, does anybody have ideas where to start debugging this further? I have tried to increase the buffer size from 32K up to the supposed max of 128K but I can't find where to do it... if anyone could shed any light I would most grateful, do you think increasing the buffer would solve this, as it would give more time to trigger the irq and get the data out before overrun?

I have tried multiple userspace programs to do the capture and the best so far is arecord initialized like this:

nice -n -20 arecord -D hw:0,0 -f cd -v jack-test.wav

Quoted 28 lines
root@beaglebone:~# nice -n -20 arecord -D hw:0,0 -f dat -v jack-test.wav
Recording WAVE 'jack-test.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo
DEBUG: buffer_time = 682667
DEBUG: max_buffer_size = 32768
Hardware PCM card 0 'AM335x-EVM' device 0 subdevice 0
Its setup is:
  stream       : CAPTURE
  access       : RW_INTERLEAVED
  format       : S16_LE
  subformat    : STD
  channels     : 2
  rate         : 48000
  exact rate   : 48000 (48000/1)
  msbits       : 16
  buffer_size  : 32768
  period_size  : 2048
  period_time  : 42666
  tstamp_mode  : NONE
  period_step  : 1
  avail_min    : 2048
  period_event : 0
  start_threshold  : 1
  stop_threshold   : 32768
  silence_threshold: 0
  silence_size : 0
  boundary     : 1073741824
  appl_ptr     : 0
  hw_ptr       : 0
Quoted 8 lines
overrun!!! (at least 221.598 ms long)
Status:
  state       : XRUN
  trigger_time: 1389534120.970142840
  tstamp      : 1389534121.191651631
  delay       : 0
  avail       : 32768
  avail_max   : 32768

If you need any more information or debugging output please let me know.

Regards,

Signature · 5 lines
  Jack Mitchell ([email protected])
  Embedded Systems Engineer
  http://www.embed.me.uk

-- 
#1 lore raw
Quoted 8 lines · Jack Mitchell

I am currently trying to debug a buffer overrun when capturing with the BeagleBone Black and Audio Cape attached on 3.13-rc8, this is pretty much the same setup as the am335x-evm. The following is the traceback captured using the XRUN_BUFFER_DEBUG kernel config option. I think an interrupt is taking too long to return.

[snip

Ok, so I managed to enlarge the buffer by increasing the max_buffer_bytes in snd_pcm_hardware capture struct. However, it doesn't really make sense... The original value was (128*1024) which should give a buffer of 128K, but in reality it gave a buffer of 32K. Now when I was hacking last night it got to the point where I just started twiddling knobs to see what would happen, and it turns out that changing the max_buffer_bytes to (256*1024) gave me 64K of buffer. So, I don't have a clue what is going on here, but I now have enough buffer to get the audio data captured and written out before an overflow occurs.

Cheers,

Signature · 5 lines
  Jack Mitchell ([email protected])
  Embedded Systems Engineer
  Cambridgeshire, UK
  http://www.embed.me.uk
--