Wrong mac address when i used ath10k driver
Hi all,
When i used the driver of the ath10k(backports-3.13.2-1) to drive the 11ac mini-pcie WIFI card(9880) on the ubuntu 12.04(based x86), the card seems to be working but i got a wrong mac address when i used the following command. Though i changed the other mini-pcie card, i got the same mac address.
---------------
root@ubuntu:~$ cat /sys/class/ieee80211/phy0/addresses 00:03:07:12:34:56 ---------------
If anybody get the same this problem, could you please tell me how to fix it.
Any suggestions would be helpful.
ps:
start log when i grep ath as following:
root@ubuntu:~$ dmesg | grep ath [ 25.240895] ath10k_pci 0000:04:00.0: BAR 0: assigned [mem 0xf0400000-0xf05fffff 64bit] [ 25.240918] ath10k_pci 0000:04:00.0: BAR 0: set to [mem 0xf0400000-0xf05fffff 64bit] (PCI address [0xf0400000-0xf05fffff]) [ 25.240932] ath10k_pci 0000:04:00.0: enabling device (0000 -> 0002) [ 25.240943] ath10k_pci 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 25.241008] ath10k_pci 0000:04:00.0: setting latency timer to 64 [ 25.241481] ath10k: MSI-X didn't succeed (1), trying MSI [ 25.241549] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 25.241582] ath10k: MSI interrupt handling [ 25.274432] ath10k: Hardware name qca988x hw2.0 version 0x4100016c [ 26.645636] ath10k: UART prints disabled [ 26.649723] ath10k: firmware 999.999.0.636 booted [ 26.659427] ath10k: htt target version 2.1 [ 26.659951] ath: EEPROM regdomain: 0x0 [ 26.659953] ath: EEPROM indicates default country code should be used [ 26.659954] ath: doing EEPROM country->regdmn map search [ 26.659956] ath: country maps to regdmn code: 0x3a [ 26.659958] ath: Country alpha2 being used: US [ 26.659960] ath: Regpair used: 0x3a [ 62.880138] type=1400 audit(1395133013.810:12): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1117 comm="apparmor_parser" [ 62.880710] type=1400 audit(1395133013.810:13): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1117 comm="apparmor_parser" [ 63.953074] ath10k: MSI-X didn't succeed (1), trying MSI [ 63.953152] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 63.953190] ath10k: MSI interrupt handling [ 65.135257] ath10k: UART prints disabled [ 65.139331] ath10k: firmware 999.999.0.636 booted [ 65.149084] ath10k: htt target version 2.1 [ 89.023995] ath10k: timed out while waiting for scan to stop [ 89.023998] ath10k: could not stop scan. its still in progress [ 91.068213] type=1400 audit(1395133042.038:25): apparmor="DENIED" operation="open" parent=2372 profile="/usr/lib/telepathy/mission-control-5" name="/usr/local/lib/libsqlite3.so.0.8.6" pid=2373 comm="mission-control" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
Thanks.
Rex wang
2014-03-07
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Can you confirm that it is phy0 and not any others (phyX)?
----
Chun-Yeow
Quoted 63 lines · wangdc
Hi all,
When i used the driver of the ath10k(backports-3.13.2-1) to drive the 11ac mini-pcie WIFI card(9880)
on the ubuntu 12.04(based x86), the card seems to be working but i got a wrong mac address when
i used the following command. Though i changed the other mini-pcie card, i got the same mac address.
---------------root@ubuntu:~$ cat /sys/class/ieee80211/phy0/addresses 00:03:07:12:34:56 ---------------If anybody get the same this problem, could you please tell me how to fix it.
Any suggestions would be helpful.
ps:
start log when i grep ath as following:root@ubuntu:~$ dmesg | grep ath [ 25.240895] ath10k_pci 0000:04:00.0: BAR 0: assigned [mem 0xf0400000-0xf05fffff 64bit] [ 25.240918] ath10k_pci 0000:04:00.0: BAR 0: set to [mem 0xf0400000-0xf05fffff 64bit] (PCI address [0xf0400000-0xf05fffff]) [ 25.240932] ath10k_pci 0000:04:00.0: enabling device (0000 -> 0002) [ 25.240943] ath10k_pci 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 25.241008] ath10k_pci 0000:04:00.0: setting latency timer to 64 [ 25.241481] ath10k: MSI-X didn't succeed (1), trying MSI [ 25.241549] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 25.241582] ath10k: MSI interrupt handling [ 25.274432] ath10k: Hardware name qca988x hw2.0 version 0x4100016c [ 26.645636] ath10k: UART prints disabled [ 26.649723] ath10k: firmware 999.999.0.636 booted [ 26.659427] ath10k: htt target version 2.1 [ 26.659951] ath: EEPROM regdomain: 0x0 [ 26.659953] ath: EEPROM indicates default country code should be used [ 26.659954] ath: doing EEPROM country->regdmn map search [ 26.659956] ath: country maps to regdmn code: 0x3a [ 26.659958] ath: Country alpha2 being used: US [ 26.659960] ath: Regpair used: 0x3a [ 62.880138] type=1400 audit(1395133013.810:12): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1117 comm="apparmor_parser" [ 62.880710] type=1400 audit(1395133013.810:13): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1117 comm="apparmor_parser" [ 63.953074] ath10k: MSI-X didn't succeed (1), trying MSI [ 63.953152] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 63.953190] ath10k: MSI interrupt handling [ 65.135257] ath10k: UART prints disabled [ 65.139331] ath10k: firmware 999.999.0.636 booted [ 65.149084] ath10k: htt target version 2.1 [ 89.023995] ath10k: timed out while waiting for scan to stop [ 89.023998] ath10k: could not stop scan. its still in progress [ 91.068213] type=1400 audit(1395133042.038:25): apparmor="DENIED" operation="open" parent=2372 profile="/usr/lib/telepathy/mission-control-5" name="/usr/local/lib/libsqlite3.so.0.8.6" pid=2373 comm="mission-control" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0Thanks.
Quoted 7 lines
Rex wang
2014-03-07_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Dear Chun Yeow
Thank you for your reply. I confirm that it is phy0.
Rex wang
Quoted 78 lines · Yeoh Chun-Yeow
Can you confirm that it is phy0 and not any others (phyX)?
----
Chun-YeowQuoted 63 lines · wangdc
Hi all,
When i used the driver of the ath10k(backports-3.13.2-1) to drive the 11ac mini-pcie WIFI card(9880)
on the ubuntu 12.04(based x86), the card seems to be working but i got a wrong mac address when
i used the following command. Though i changed the other mini-pcie card, i got the same mac address.
---------------root@ubuntu:~$ cat /sys/class/ieee80211/phy0/addresses 00:03:07:12:34:56 ---------------If anybody get the same this problem, could you please tell me how to fix it.
Any suggestions would be helpful.
ps:
start log when i grep ath as following:root@ubuntu:~$ dmesg | grep ath [ 25.240895] ath10k_pci 0000:04:00.0: BAR 0: assigned [mem 0xf0400000-0xf05fffff 64bit] [ 25.240918] ath10k_pci 0000:04:00.0: BAR 0: set to [mem 0xf0400000-0xf05fffff 64bit] (PCI address [0xf0400000-0xf05fffff]) [ 25.240932] ath10k_pci 0000:04:00.0: enabling device (0000 -> 0002) [ 25.240943] ath10k_pci 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 25.241008] ath10k_pci 0000:04:00.0: setting latency timer to 64 [ 25.241481] ath10k: MSI-X didn't succeed (1), trying MSI [ 25.241549] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 25.241582] ath10k: MSI interrupt handling [ 25.274432] ath10k: Hardware name qca988x hw2.0 version 0x4100016c [ 26.645636] ath10k: UART prints disabled [ 26.649723] ath10k: firmware 999.999.0.636 booted [ 26.659427] ath10k: htt target version 2.1 [ 26.659951] ath: EEPROM regdomain: 0x0 [ 26.659953] ath: EEPROM indicates default country code should be used [ 26.659954] ath: doing EEPROM country->regdmn map search [ 26.659956] ath: country maps to regdmn code: 0x3a [ 26.659958] ath: Country alpha2 being used: US [ 26.659960] ath: Regpair used: 0x3a [ 62.880138] type=1400 audit(1395133013.810:12): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1117 comm="apparmor_parser" [ 62.880710] type=1400 audit(1395133013.810:13): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1117 comm="apparmor_parser" [ 63.953074] ath10k: MSI-X didn't succeed (1), trying MSI [ 63.953152] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 63.953190] ath10k: MSI interrupt handling [ 65.135257] ath10k: UART prints disabled [ 65.139331] ath10k: firmware 999.999.0.636 booted [ 65.149084] ath10k: htt target version 2.1 [ 89.023995] ath10k: timed out while waiting for scan to stop [ 89.023998] ath10k: could not stop scan. its still in progress [ 91.068213] type=1400 audit(1395133042.038:25): apparmor="DENIED" operation="open" parent=2372 profile="/usr/lib/telepathy/mission-control-5" name="/usr/local/lib/libsqlite3.so.0.8.6" pid=2373 comm="mission-control" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0Thanks.
Quoted 7 lines
Rex wang
2014-03-07_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k.
Signature · 18 lines
============================================= 王登成 大连华信计算机技术股份有限公司 中国大连高新技术产业园区黄浦路977号 华信(国际)软件园 邮编:116023 电话:+86-411-85996869 (已变更) 传真:+86-411-85996976 手 机:+86-138-89523320 E-mail:[email protected] ============================================= 请注意:这是一封保密邮件,如果您 不是邮件中的收信人, 请尽快发邮件通知我,并将邮件删除。给您工作带来不便,十分抱歉。 _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 2 lines · wangdc
When i used the driver of the ath10k(backports-3.13.2-1) to drive the 11ac mini-pcie WIFI card(9880)
What board is this? Something based on XB140 design?
Quoted 41 lines
on the ubuntu 12.04(based x86), the card seems to be working but i got a wrong mac address when
i used the following command. Though i changed the other mini-pcie card, i got the same mac address.
---------------root@ubuntu:~$ cat /sys/class/ieee80211/phy0/addresses 00:03:07:12:34:56 ---------------If anybody get the same this problem, could you please tell me how to fix it.
Any suggestions would be helpful.
ps:
start log when i grep ath as following:root@ubuntu:~$ dmesg | grep ath [ 25.240895] ath10k_pci 0000:04:00.0: BAR 0: assigned [mem 0xf0400000-0xf05fffff 64bit] [ 25.240918] ath10k_pci 0000:04:00.0: BAR 0: set to [mem 0xf0400000-0xf05fffff 64bit] (PCI address [0xf0400000-0xf05fffff]) [ 25.240932] ath10k_pci 0000:04:00.0: enabling device (0000 -> 0002) [ 25.240943] ath10k_pci 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 25.241008] ath10k_pci 0000:04:00.0: setting latency timer to 64 [ 25.241481] ath10k: MSI-X didn't succeed (1), trying MSI [ 25.241549] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 25.241582] ath10k: MSI interrupt handling [ 25.274432] ath10k: Hardware name qca988x hw2.0 version 0x4100016c [ 26.645636] ath10k: UART prints disabled [ 26.649723] ath10k: firmware 999.999.0.636 booted [ 26.659427] ath10k: htt target version 2.1 [ 26.659951] ath: EEPROM regdomain: 0x0 [ 26.659953] ath: EEPROM indicates default country code should be used [ 26.659954] ath: doing EEPROM country->regdmn map search [ 26.659956] ath: country maps to regdmn code: 0x3a [ 26.659958] ath: Country alpha2 being used: US [ 26.659960] ath: Regpair used: 0x3a [ 62.880138] type=1400 audit(1395133013.810:12): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1117 comm="apparmor_parser"
Quoted 8 lines
[ 62.880710] type=1400 audit(1395133013.810:13): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1117 comm="apparmor_parser" [ 63.953074] ath10k: MSI-X didn't succeed (1), trying MSI [ 63.953152] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 63.953190] ath10k: MSI interrupt handling [ 65.135257] ath10k: UART prints disabled [ 65.139331] ath10k: firmware 999.999.0.636 booted
I'm guessing otp.bin fails and use the default board file. Can you try firmware 10.1.467.2-1? Just get the firmware here:
https://github.com/kvalo/ath10k-firmware/tree/master/10.1
And rename it to firmware-2.bin:
cp firmware-2.bin_10.1.467.2-1 /lib/firmware/ath10k/QCA988X/hw2.0/firmware-2.bin
And reload ath10k.
Signature · 6 lines
Kalle Valo _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Dear Kalle Valo
Now I can get the mac address correctly using the following method. Thank you very much.
Rex wang
Quoted 58 lines · Kalle Valo
Quoted 2 lines · wangdc
When i used the driver of the ath10k(backports-3.13.2-1) to drive the 11ac mini-pcie WIFI card(9880)
What board is this? Something based on XB140 design?
Quoted 41 lines
on the ubuntu 12.04(based x86), the card seems to be working but i got a wrong mac address when
i used the following command. Though i changed the other mini-pcie card, i got the same mac address.
---------------root@ubuntu:~$ cat /sys/class/ieee80211/phy0/addresses 00:03:07:12:34:56 ---------------If anybody get the same this problem, could you please tell me how to fix it.
Any suggestions would be helpful.
ps:
start log when i grep ath as following:root@ubuntu:~$ dmesg | grep ath [ 25.240895] ath10k_pci 0000:04:00.0: BAR 0: assigned [mem 0xf0400000-0xf05fffff 64bit] [ 25.240918] ath10k_pci 0000:04:00.0: BAR 0: set to [mem 0xf0400000-0xf05fffff 64bit] (PCI address [0xf0400000-0xf05fffff]) [ 25.240932] ath10k_pci 0000:04:00.0: enabling device (0000 -> 0002) [ 25.240943] ath10k_pci 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 25.241008] ath10k_pci 0000:04:00.0: setting latency timer to 64 [ 25.241481] ath10k: MSI-X didn't succeed (1), trying MSI [ 25.241549] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 25.241582] ath10k: MSI interrupt handling [ 25.274432] ath10k: Hardware name qca988x hw2.0 version 0x4100016c [ 26.645636] ath10k: UART prints disabled [ 26.649723] ath10k: firmware 999.999.0.636 booted [ 26.659427] ath10k: htt target version 2.1 [ 26.659951] ath: EEPROM regdomain: 0x0 [ 26.659953] ath: EEPROM indicates default country code should be used [ 26.659954] ath: doing EEPROM country->regdmn map search [ 26.659956] ath: country maps to regdmn code: 0x3a [ 26.659958] ath: Country alpha2 being used: US [ 26.659960] ath: Regpair used: 0x3a [ 62.880138] type=1400 audit(1395133013.810:12): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1117 comm="apparmor_parser"Quoted 8 lines
[ 62.880710] type=1400 audit(1395133013.810:13): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1117 comm="apparmor_parser" [ 63.953074] ath10k: MSI-X didn't succeed (1), trying MSI [ 63.953152] ath10k_pci 0000:04:00.0: irq 45 for MSI/MSI-X [ 63.953190] ath10k: MSI interrupt handling [ 65.135257] ath10k: UART prints disabled [ 65.139331] ath10k: firmware 999.999.0.636 bootedI'm guessing otp.bin fails and use the default board file. Can you try firmware 10.1.467.2-1? Just get the firmware here:
Quoted 8 lines
https://github.com/kvalo/ath10k-firmware/tree/master/10.1
And rename it to firmware-2.bin:
cp firmware-2.bin_10.1.467.2-1
/lib/firmware/ath10k/QCA988X/hw2.0/firmware-2.binAnd reload ath10k.
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k