Some clarification regarding rfc3484 (6724) - Rule 8 Prefer smaller scope
Subsystems (2)
I had configured my local interface as follows :
ifconfig eth0 inet6 add fe80::1/64
ifconfig eth0 inet6 add fec0::1/10
And /etc/hosts contains :
fe80::2 server.org
fec0::2 server.org
The above two interfaces in /etc/hosts are not configured. Just to get the result from getaddrinfo().
So according to rfc3484 , link-local has lower scope when compared to site-local .
So i think fe80::2 should be returned first and then later fec0::2
In my fedora ( any kernel ), getaddrinfo() is preferring site-local first instead of link-local.
So when looking into the getaddrinfo() glibc implementation , when two or more addresses are available (code flow):
1) create a udp datagram socket
2) connect to the destination addresses returned from gaih_inet ( not sorted yet ). This was done inorder to get the source address from the kernel (using ipv6_get_saddr_eval() we get the preferred source for each destination). Actually doesnt need the destination to be reachable . #netstat | grep -i udp
udp 0 0 fec0::1:34236 server.org:http
ESTABLISHED
3) getsockname to get the source address and store in result combo array.
So __connect() to site-local becomes successfull . But __connect() to link-local is not successfull .
Hence rfc3484_sort() in glibc changes the order and prefers site-local first .
i.e /* Rule 1: Avoid unusable destinations.
We have the got_source_addr flag set if the destination is
reachable. */
if (a1->got_source_addr && ! a2->got_source_addr)
a1->got_source_addr is false because connect to link-local failed.
So my questions are :
1) Can this be a problem somewhere around ip6_datagram_connect() [ because connect fails ]
2) Can this be a problem with the parsing of glibc getaddrinfo ? [ something like sin6_scope_id being not set properly ]
3) Or this is the expected behaviour or am i missing out something ?
Any suggestions ?
Thank you,
Sumanth K
Quoted 42 lines · sumanth
I had configured my local interface as follows :
ifconfig eth0 inet6 add fe80::1/64
ifconfig eth0 inet6 add fec0::1/10And
/etc/hostscontains :
fe80::2 server.org
fec0::2 server.orgThe above two interfaces in
/etc/hostsare not configured. Just to get the result fromgetaddrinfo().So according to rfc3484 , link-local has lower scope when compared to site-local .
So i think fe80::2 should be returned first and then later fec0::2In my fedora ( any kernel ),
getaddrinfo()is preferring site-local first instead of link-local.So when looking into the
getaddrinfo()glibc implementation , when two or more addresses are available (code flow):
1) create a udp datagram socket
2) connect to the destination addresses returned fromgaih_inet( not sorted yet ). This was done inorder to get the source address from the kernel (usingipv6_get_saddr_eval()we get the preferred source for each destination). Actually doesnt need the destination to be reachable . #netstat | grep -i udp
udp 0 0 fec0::1:34236 server.org:http
ESTABLISHED3) getsockname to get the source address and store in result combo array.
So
__connect()to site-local becomes successfull . But__connect()to link-local is not successfull .Hence
rfc3484_sort()in glibc changes the order and prefers site-local first .i.e /* Rule 1: Avoid unusable destinations.
We have thegot_source_addrflag set if the destination is
reachable. */
if (a1->got_source_addr&& !a2->got_source_addr)
Quoted 8 lines
a1->got_source_addris false because connect to link-local failed.So my questions are :
1) Can this be a problem somewhere aroundip6_datagram_connect()[ because connect fails ]
2) Can this be a problem with the parsing of glibc getaddrinfo ? [ something likesin6_scope_idbeing not set properly ]
3) Or this is the expected behaviour or am i missing out something ?
I was testing one of the tahi testcase :
DstSelectRule8.seq - Destination Address Selection
Check Rule 8(Prefer smaller scopee)
Rule 8: Prefer smaller scope.
If Scope(DA) < Scope(DB), then prefer DA.
The configuration was done as shown above. . So link-local was expected. But returned value was site-local.
- So while looking into the ip6_datagram_connect(), inorder for the connect() call to succeed for link-local address, it requires the sk_bound_dev_if field of the sk to be set. So this can be done using setsockopt( fd, SOL_SOCKET, SO_BINDTODEVICE, device , strlen(device) +
1) from the application side / library.
- But however __connect in glibc getaddrinfo() fails in case of link-local ( when there are more than 2 address ) . But ingetaddrinfo.c, if we add a patch such that setsockopt() is done
before __connect() and __getsockname() if it is a LINKLOCAL address, then link-local address is returned first and then later site-local ( which is expected as per tahi testcase ). i.e rfc3484_sort() goes into Rule 8 of destination address selection ( otherwise it returns from Rule1 as source address of link-local wont be set itself as connect() fails)
- But rfc4472 mentions that Link-local addresses should never be published in DNS (whether in
forward or reverse tree), because they have only local (to the connected link) significance.
- So whether rfc4472 means that we shouldnt specify link-local address in /etc/hosts as well ?
- Or it is expected to return site-local first ? [ If i do setsockopt() in glibc before connect() iff link-local address, then link-local is returned first ]. So if it is expected to return link-local , then it is a bug...
Any help/suggestions would be good.
Quoted 6 lines
Any suggestions ?
Thank you,
Sumanth K