AM335x not working anymore
Hi,
i've just pulled newest u-boot and tried it on my custom AM335x board without success. It hangs after (successful) running init_s function.
....
Enable clock module - 44e0001c
Enable clock module - 44e000d0
Enable clock module - 44e00028
is the last debug output.
After some time the watchdog is doing his job and restarts again.
Okay ... thinking maybe something had become incompatible with my customization ... so let's try the beaglebone board. Same behaviour :-(
I debugged around and found finally this commit, which breaks the support:
/
//commit id: f0c3a6c4ad09210d5d4aeafe87685ee75e5683d6//
//
// ARM: SPL: do not set gd again//
////
// Just before calling board_init_f, crt0.S has already// // reserved space for the initial gd on the stack. There// // should be no need to allocate it again.//
////
// cc: Albert ARIBAUD <[email protected]>//
// Signed-off-by: Jeroen Hofstee <[email protected]>/
I have reverted this commit in my branch and everything works fine. Finally i have to admit, that i do not fully understand whats going on there in detail.
What i can see, is that there live more than one instance of the "gd". One is setup in arch/arm/lib/cpu/armv7/lowlevel_init.S, another one is setup in arch/arm/lib/crt0.S.
Within the "gd-ptr" is loaded to &gdata (gdata __attribute__ ((section(".data")))
I am a bit confused all about this :-)
Any ideas ?
best regards,
Hannes
Quoted 35 lines · Hannes Petermaier
Hi,
i've just pulled newest u-boot and tried it on my custom AM335x board without success. It hangs after (successful) running
init_sfunction.....
Enable clock module -44e0001c
Enable clock module -44e000d0
Enable clock module -44e00028is the last debug output.
After some time the watchdog is doing his job and restarts again.Okay ... thinking maybe something had become incompatible with my customization ... so let's try the beaglebone board. Same behaviour :-(
I debugged around and found finally this commit, which breaks the support:
/
//commit id: f0c3a6c4ad09210d5d4aeafe87685ee75e5683d6//
//
// ARM: SPL: do not set gd again//
////// Just before calling board_init_f, crt0.S has already// // reserved space for the initial gd on the stack. There// // should be no need to allocate it again.//////
// cc: Albert ARIBAUD <[email protected]>//
// Signed-off-by: Jeroen Hofstee <[email protected]>/I have reverted this commit in my branch and everything works fine. Finally i have to admit, that i do not fully understand whats going on there in detail.
Quoted 7 lines
What i can see, is that there live more than one instance of the "gd". One is setup in
arch/arm/lib/cpu/armv7/lowlevel_init.S, another one is setup inarch/arm/lib/crt0.S.
Within the "gd-ptr" is loaded to &gdata (gdata__attribute__((section(".data")))I am a bit confused all about this :-)
I just finished bisecting down to this being a problem commit as well. As far as I can see, the commit in question doesn't make sense. Or perhaps rather, the comments in crt0.S aren't quite right in the SPL case where we don't place the initial gd on the stack, it's in the .data section.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20140916/aca2bf2d/attachment.pgp>
Hello Hannes, Tom,
Quoted 43 lines · Tom Rini
Quoted 41 lines · Hannes Petermaier
Hi,
i've just pulled newest u-boot and tried it on my custom AM335x board without success. It hangs after (successful) running
init_sfunction.....
Enable clock module -44e0001c
Enable clock module -44e000d0
Enable clock module -44e00028is the last debug output.
After some time the watchdog is doing his job and restarts again.Okay ... thinking maybe something had become incompatible with my customization ... so let's try the beaglebone board. Same behaviour :-(
I debugged around and found finally this commit, which breaks the support:
/
//commit id: f0c3a6c4ad09210d5d4aeafe87685ee75e5683d6//
//
// ARM: SPL: do not set gd again//
////// Just before calling board_init_f, crt0.S has already// // reserved space for the initial gd on the stack. There// // should be no need to allocate it again.//////
// cc: Albert ARIBAUD <[email protected]>//
// Signed-off-by: Jeroen Hofstee <[email protected]>/I have reverted this commit in my branch and everything works fine. Finally i have to admit, that i do not fully understand whats going on there in detail.
What i can see, is that there live more than one instance of the "gd". One is setup in
arch/arm/lib/cpu/armv7/lowlevel_init.S, another one is setup inarch/arm/lib/crt0.S.
Within the "gd-ptr" is loaded to &gdata (gdata__attribute__((section(".data")))
Quoted 8 lines
Quoted 1 line
I am a bit confused all about this :-)
I just finished bisecting down to this being a problem commit as well. As far as I can see, the commit in question doesn't make sense. Or perhaps rather, the comments in
crt0.Saren't quite right in the SPL case where we don't place the initial gd on the stack, it's in the .data section.
As far as I can tell there are two gdata's is the SPL case. One on the stack and one in gdata. Can't the later not be removed, so we end up with a single gd init in crt0.S? Before this patch the code switches back and forth between the two, which is at least a bit weird.
I will have a closer look at the call path, especially why it used to work...
Regards,
Jeroen
Hi,
Quoted 53 lines · Jeroen Hofstee
Hello Hannes, Tom,
Quoted 43 lines · Tom Rini
Quoted 41 lines · Hannes Petermaier
Hi,
i've just pulled newest u-boot and tried it on my custom AM335x board without success. It hangs after (successful) running
init_sfunction.....
Enable clock module -44e0001c
Enable clock module -44e000d0
Enable clock module -44e00028is the last debug output.
After some time the watchdog is doing his job and restarts again.Okay ... thinking maybe something had become incompatible with my customization ... so let's try the beaglebone board. Same behaviour :-(
I debugged around and found finally this commit, which breaks the support:
/
//commit id: f0c3a6c4ad09210d5d4aeafe87685ee75e5683d6//
//
// ARM: SPL: do not set gd again//
////// Just before calling board_init_f, crt0.S has already// // reserved space for the initial gd on the stack. There// // should be no need to allocate it again.//////
// cc: Albert ARIBAUD <[email protected]>//
// Signed-off-by: Jeroen Hofstee <[email protected]>/I have reverted this commit in my branch and everything works fine. Finally i have to admit, that i do not fully understand whats going on there in detail.
What i can see, is that there live more than one instance of the "gd". One is setup in
arch/arm/lib/cpu/armv7/lowlevel_init.S, another one is setup inarch/arm/lib/crt0.S.
Within the "gd-ptr" is loaded to &gdata (gdata__attribute__((section(".data")))Quoted 7 lines
Quoted 1 line
I am a bit confused all about this :-)
I just finished bisecting down to this being a problem commit as well. As far as I can see, the commit in question doesn't make sense. Or perhaps rather, the comments in
crt0.Saren't quite right in the SPL case where we don't place the initial gd on the stack, it's in the .data section.
Quoted 9 lines
As far as I can tell there are two gdata's is the SPL case. One on the stack and one in gdata. Can't the later not be removed, so we end up with a single gd init in
crt0.S? Before this patch the code switches back and forth between the two, which is at least a bit weird.I will have a closer look at the call path, especially why it used to work...
While in my opinion the omap code is to blame for doing more then needed in cpu_init_crit and eventually in s_init, (and hence needing its own gdata) I am more then fine with reverting this patch for now, but I would like to have only a single gdata eventually, initialized only once.
Can you try this patch [1], just for educational purposes. It will scare Tom a bit since dram is setup before the console, but I still have to find an user of that.
Regards,
Jeroen