Skip to contentSkip to conversation

Need help with u-boot problem with usb-keyboard / kvm switch

U-Boot Hans de Goede 5 participants 8 messages Sep 17, 2014 – Sep 19, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

Hi Marek, et al,

I'm working on cleaning up Luc's hdmi out support patchset for sunxi.

As part of this I want to also add support for usb keyboards, so as to get a full console without needing to solder wires to testpoints on some boards :)

So when I plug in the usb coming from my kvm I get this:

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80 3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found

And the usb keyboard does not work.

If I plug in a single usb-2 hub (no ohci support for sunxi in u-boot yet), then things do work, but after a few minutes of inactivity the usb code starts spamming the console with:

EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
...

Could this be a problem with the phy settings (iow a sunxi specific problem)?

When using the kvm on my pc, the tree structure looks like this:

/: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 4: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M
|__ Port 2: Dev 3, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 3: Dev 11, If 0, Class=Human Interface Device, Driver=usbhid, 1.5M |__ Port 4: Dev 9, If 0, Class=Hub, Driver=hub/4p, 12M
|__ Port 1: Dev 10, If 0, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 1: Dev 10, If 1, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 1: Dev 10, If 2, Class=Human Interface Device, Driver=usbhid, 12M

Hmm, after a bit longer I also get these errors:

ERROR: v7_dcache_inval_range - start address is not aligned - 0xe59ff014

Could the problem be that the usb code is feeding unaligned buffers to the ehci controller ?

Regards,

Hans

#1 lore raw
Quoted 4 lines · Hans de Goede

Hi Marek, et al,

I'm working on cleaning up Luc's hdmi out support patchset for sunxi.

?

Luc Verhaegen.

#2 lore raw
Quoted 7 lines · Luc Verhaegen
Quoted 4 lines · Hans de Goede

Hi Marek, et al,

I'm working on cleaning up Luc's hdmi out support patchset for sunxi.

?

Your email is missing it's contents, is that at typo ?

Best regards,
Marek Vasut

#3 lore raw
In reply to Luc Verhaegen

Hi,

Quoted 7 lines · Luc Verhaegen
Quoted 4 lines · Hans de Goede

Hi Marek, et al,

I'm working on cleaning up Luc's hdmi out support patchset for sunxi.

?

Cleaning up may not have been the best choice of words, I was talking about the rebase on top of upstream u-boot + the various fixes you already know about.

I plan to submit a patch-set to the kernel for the clock resource stuff for simplefb to the proper lists for that discussion soon, and assuming that gets accepted I would like to land the hdmi support in upstream u-boot soon.

Regards,

Hans

#4 lore raw
Quoted 10 lines · Hans de Goede

Hi,

Cleaning up may not have been the best choice of words, I was talking about the rebase on top of upstream u-boot + the various fixes you already know about.

I plan to submit a patch-set to the kernel for the clock resource stuff for simplefb to the proper lists for that discussion soon, and assuming that gets accepted I would like to land the hdmi support in upstream u-boot soon.

Ok, thanks for getting me up to date on this.

As for simplefb, i had given up on that, and wanted to cough up an alternate driver that simply wouldn't be called that. But as usual, i am all over the place. So let's see how the simplefb route goes. Good luck.

Thanks,

Luc Verhaegen.

#5 lore raw
In reply to Hans de Goede

Hi Hans,

Quoted 23 lines · Hans de Goede

Hi Marek, et al,

I'm working on cleaning up Luc's hdmi out support patchset for sunxi.

As part of this I want to also add support for usb keyboards, so as to get a full console without needing to solder wires to testpoints on some boards :)

So when I plug in the usb coming from my kvm I get this:

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80 3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found

And the usb keyboard does not work.

If I plug in a single usb-2 hub (no ohci support for sunxi in u-boot yet), then things do work, but after a few minutes of inactivity the usb code starts spamming the console with:

Quoted 7 lines

EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
...

Could this be a problem with the phy settings (iow a sunxi specific problem)?

Probably not.

We've seen the same thing on SABRE Lite and Nitrogen6X boards.

U-Boot > usb start ; setenv stdin serial,usbkbd
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Timeout poll on interrupt endpoint
Failed to get keyboard state from device 1c4f:0002
U-Boot > usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Mass Storage (480 Mb/s, 100mA)
Generic Mass Storage 4A3709D5

3 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|

  +-4  Hub (480 Mb/s, 2mA)
    |
    +-5  Human Interface (1.5 Mb/s, 100mA)
    |    Logitech USB Optical Mouse
    |
    +-6  Hub (480 Mb/s, 100mA)
    | |   USB 2.0 Hub
    | |
    | +-7  Human Interface (1.5 Mb/s, 98mA)
    |      USB USB Keykoard
    |
    +-8   (12 Mb/s, 100mA)

Oddly, the issue seems to be specific to **some** USB keyboards.

We have some (mostly older) USB keyboards that just work and have had investigation on our to-do list for quite some time now.

I was going to start with a question to the list:

Is anyone else using USB keyboard support?

USB mass storage seems to be pretty reliable. We have folks using it as an alternate boot for emergency situations.

Regards,

Eric

#6 lore raw
Quoted 31 lines · Eric Nelson

Hi Hans,

Quoted 28 lines · Hans de Goede

Hi Marek, et al,

I'm working on cleaning up Luc's hdmi out support patchset for sunxi.

As part of this I want to also add support for usb keyboards, so as to get a full console without needing to solder wires to testpoints on some boards :)

So when I plug in the usb coming from my kvm I get this:

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80 3 USB Device(s) found

scanning usb for storage devices... 0 Storage Device(s) found

And the usb keyboard does not work.

If I plug in a single usb-2 hub (no ohci support for sunxi in u-boot yet), then things do work, but after a few minutes of inactivity the usb code starts spamming the console with:

EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
...

Quoted 6 lines
Quoted 2 lines

Could this be a problem with the phy settings (iow a sunxi specific problem)?

Probably not.

We've seen the same thing on SABRE Lite and Nitrogen6X boards.

I agree, this happens. Which controller and driver do you use on the Sunxi hardware?

btw you can check if this is a cache issue by disabling dcache (set CONFIG_CMD_CACHE in the config and use 'dcache off' before 'usb start'). You can also patch the arch/arm/lib/cache-cp15.c functions to do additional alignment checks (always a good idea) , just like I did that in arch/arm/cpu/arm926ejs/cache.c

Best regards,
Marek Vasut

#7 lore raw
In reply to Eric Nelson

Hi All,

Quoted 77 lines · Eric Nelson

Hi Hans,

Quoted 23 lines · Hans de Goede

Hi Marek, et al,

I'm working on cleaning up Luc's hdmi out support patchset for sunxi.

As part of this I want to also add support for usb keyboards, so as to get a full console without needing to solder wires to testpoints on some boards :)

So when I plug in the usb coming from my kvm I get this:

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80 3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found

And the usb keyboard does not work.

If I plug in a single usb-2 hub (no ohci support for sunxi in u-boot yet), then things do work, but after a few minutes of inactivity the usb code starts spamming the console with:

Quoted 7 lines

EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
...

Could this be a problem with the phy settings (iow a sunxi specific problem)?

Probably not.

We've seen the same thing on SABRE Lite and Nitrogen6X boards.

U-Boot > usb start ; setenv stdin serial,usbkbd
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80 EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Timeout poll on interrupt endpoint
Failed to get keyboard state from device 1c4f:0002
U-Boot > usb tree
USB device tree:

   1  Hub (480 Mb/s, 0mA)
   |  u-boot EHCI Host Controller
   |
   +-2  Mass Storage (480 Mb/s, 100mA)
        Generic Mass Storage 4A3709D5

   3  Hub (480 Mb/s, 0mA)
   |  u-boot EHCI Host Controller
   |
   +-4  Hub (480 Mb/s, 2mA)
     |
     +-5  Human Interface (1.5 Mb/s, 100mA)
     |    Logitech USB Optical Mouse
     |
     +-6  Hub (480 Mb/s, 100mA)
     | |   USB 2.0 Hub
     | |
     | +-7  Human Interface (1.5 Mb/s, 98mA)
     |      USB USB Keykoard
     |
     +-8   (12 Mb/s, 100mA)

Oddly, the issue seems to be specific to **some** USB keyboards.

Quoted 7 lines

We have some (mostly older) USB keyboards that just work and have had investigation on our to-do list for quite some time now.

I was going to start with a question to the list:

Is anyone else using USB keyboard support?

I use the USB keyboard with following hack patch (which based on v2013.04), then it works well on my side.

--->8---

drivers/usb/host/ohci-hcd.c +0 -0
index bc17b85..b74bfd7 100644
@@ -515,6 +515,7 @@ static inline int sohci_return_job(struct ohci *hc, 

urb_priv_t *urb)

                         ohci_readl(&regs->intrdisable); /* PCI posting 
flush */
                 }
                 urb->actual_length = 0;
+#if 0
                 td_submit_job(
                                 urb->dev,
                                 urb->pipe,
@@ -523,6 +524,8 @@ static inline int sohci_return_job(struct ohci *hc, 
urb_priv_t *urb)
                                 NULL,
                                 urb,
                                 urb->interval);
+#endif
+               urb_free_priv(urb);
                 break;
         case PIPE_CONTROL:
         case PIPE_BULK:

---8<---

Quoted 8 lines

USB mass storage seems to be pretty reliable. We have folks using it as an alternate boot for emergency situations.

Regards,

Eric

Best Regards,
Bo Shen