tty: serial: msm_serial: document DT alias

From: Frank Rowand <[email protected]>

Update devicetree binding for msm_serial to reflect msm_serial_probe() getting line id (port number) from the serialN alias.

Signed-off-by Frank Rowand <[email protected]>

---
 Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt |   15 +++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)

Index: linux/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
===================================================================

Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt +43 -14

@@ -27,27 +27,52 @@ Optional properties:
 - dmas: Should contain dma specifiers for transmit and receive channels
 - dma-names: Should contain "tx" for transmit and "rx" for receive channels
 
+Note: Aliases may be defined to ensure the correct ordering of the UARTs.
+The alias serialN will result in the UART being assigned port N.  If any
+serialN alias exists, then an alias must exist for each enabled UART.  The
+serialN aliases should be in a .dts file instead of in a .dtsi file.
+
 Examples:
 
-A uartdm v1.4 device with dma capabilities.
+- A uartdm v1.4 device with dma capabilities.
+
+	serial at f991e000 {
+		compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+		reg = <0xf991e000 0x1000>;
+		interrupts = <0 108 0x0>;
+		clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
+		clock-names = "core", "iface";
+		dmas = <&dma0 0>, <&dma0 1>;
+		dma-names = "tx", "rx";
+	};
+
+- A uartdm v1.3 device without dma capabilities and part of a GSBI complex.
+
+	serial at 19c40000 {
+		compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+		reg = <0x19c40000 0x1000>,
+		<0x19c00000 0x1000>;
+		interrupts = <0 195 0x0>;
+		clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>;
+		clock-names = "core", "iface";
+	};
+
+- serialN alias.
+
+	aliases {
+		serial0 = &uarta;
+		serial1 = &uartc;
+		serial2 = &uartb;
+	};
+
+	uarta: serial at 12490000 {
+		status = "ok";
+	};
+
+	uartb: serial at 16340000 {
+		status = "ok";
+	};
 
-serial at f991e000 {
-	compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-	reg = <0xf991e000 0x1000>;
-	interrupts = <0 108 0x0>;
-	clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
-	clock-names = "core", "iface";
-	dmas = <&dma0 0>, <&dma0 1>;
-	dma-names = "tx", "rx";
-};
-
-A uartdm v1.3 device without dma capabilities and part of a GSBI complex.
-
-serial at 19c40000 {