Skip to contentSkip to conversation

ath10k: fw_stats not reporting peer_stats with 10.2

DISCUSSION Antonio Quartulli 2 participants 3 messages Dec 18, 2014 – Jan 13, 2015 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

Hello,

I have a device equipped with a ath10k driven wifi card, specifically:

qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2-00082-4-2 api 3 htt 2.1 wmi 65.109.0.0 cal file

(line grabbed from dmesg at boot time)

On my device I have configured 2 AP vifs and for each of them I would like to read the last TX rate of the associated stations.

As I've read on wireless.kernel.org this is not possible through the standard nl/cfg80211 interface and therefore I have been trying to read /sys/kernel/debug/ieee80211/phy1/ath10k/fw_stats , but this file always reports "ath10k PEER stats (0)" (no peers..).

I tried printing some debug messages here and there and the only useful information I got is that in "ath10k_wmi_10x_pull_fw_stats()" the value of "ev->num_peer_stats" is always 0.

Is this yet another fw limitation?

I also realized that upon station connection ath10k receives the WMI_10_2_PEER_RATECODE_LIST_EVENTID event but it is not handled as no handler is implemented. Might it be related with my problem ?

Thanks a lot for any information you would be able to provide :)

Cheers,

Signature · 1 line
Antonio Quartulli

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw
Quoted 1 line · Antonio Quartulli

Hello,

Hi,

Sorry for the late reply.

Quoted 10 lines

(line grabbed from dmesg at boot time)

On my device I have configured 2 AP vifs and for each of them I would like to read the last TX rate of the associated stations.

As I've read on wireless.kernel.org this is not possible through the standard nl/cfg80211 interface and therefore I have been trying to read /sys/kernel/debug/ieee80211/phy1/ath10k/fw_stats , but this file always reports "ath10k PEER stats (0)" (no peers..).

Quoted 5 lines

I tried printing some debug messages here and there and the only useful information I got is that in "ath10k_wmi_10x_pull_fw_stats()" the value of "ev->num_peer_stats" is always 0.

Is this yet another fw limitation?

Firmware stats has a very fragile ABI. Apparently 10.2 changed it again and thus is broken. I'll try to look into it more if time permits.

Quoted 3 lines

I also realized that upon station connection ath10k receives the WMI_10_2_PEER_RATECODE_LIST_EVENTID event but it is not handled as no handler is implemented. Might it be related with my problem ?

No. That's not the problem.

Michał

#2 lore raw
Quoted 10 lines · Michal Kazior
Quoted 5 lines · Antonio Quartulli

I tried printing some debug messages here and there and the only useful information I got is that in "ath10k_wmi_10x_pull_fw_stats()" the value of "ev->num_peer_stats" is always 0.

Is this yet another fw limitation?

Firmware stats has a very fragile ABI. Apparently 10.2 changed it again and thus is broken. I'll try to look into it more if time permits.

Thank Michał!
I will be happy to test any change you might be able to provide.

Cheers,

Signature · 1 line
Antonio Quartulli