Skip to contentSkip to conversation

ath10k and 802.11s support?

DISCUSSION Ben Greear 2 participants 3 messages Mar 10, 2015 – Mar 11, 2015 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore

Ben Greear

author
#0 lore raw

Anyone know what it would take to get ath10k to support 802.11s?

As you know, I'm not above modifying ath10k firmware, but I also do not have a huge amount of time to put into this, so if changes needed are extensive, then probably I cannot do it now...

Thanks,
Ben

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#1 lore raw

Hi, Ben

I have forwarded my email two years ago related to fw supporting 802.11s.

-----
Chun-Yeow

---------- Forwarded message ----------
From: Yeoh Chun-Yeow <[email protected]>
Date: Mon, Mar 3, 2014 at 10:21 AM
Subject: Mesh Support in ath10k
To: Kalle Valo <[email protected]>

Hi, Kalle Valo

Currently, I am investigating the possibility of putting mesh or o11s support in ath10k by utilizing the adhoc mode available in ath10k.

I have compiled the following issues that need to address to enable the mesh support:

1. Beacon Filtering
Currenly, adhoc mode only allowed the beacon with the BSSID set by the ath10k_wmi_vdev_up to pass to mac80211. Continuous background scanning may not be good since we need to receive the beacon for synchronization purpose. FYI, mesh uses the BSSID similar to its own vif mac addr.

2. QoS Data Frame for broadcast data frame
Currently, only non-QoS data allowed for broadcast frame as I observed.

3. QoS Control Field, no stripped off
We need to set the bit-8 of QoS control field to indicate the presence of mesh control field.

I believe that we need to have some changes on the Firmware to make this work.

Please kindly let me know is that possible to make arrangement of FW changes.

Thanks

Regards,
Chun-Yeow

Quoted 16 lines · Ben Greear

Anyone know what it would take to get ath10k to support 802.11s?

As you know, I'm not above modifying ath10k firmware, but I also do not have a huge amount of time to put into this, so if changes needed are extensive, then probably I cannot do it now...

Thanks,
Ben

--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com

Quoted 4 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

author
#2 lore raw
Quoted 3 lines · Yeoh Chun-Yeow

Hi, Ben

I have forwarded my email two years ago related to fw supporting 802.11s.

Thanks for the info.

I'll look into this a bit more when I finish some other pending work.

Thanks,
Ben

Quoted 65 lines

-----
Chun-Yeow

---------- Forwarded message ----------
From: Yeoh Chun-Yeow <[email protected]>
Date: Mon, Mar 3, 2014 at 10:21 AM
Subject: Mesh Support in ath10k
To: Kalle Valo <[email protected]>

Hi, Kalle Valo

Currently, I am investigating the possibility of putting mesh or o11s support in ath10k by utilizing the adhoc mode available in ath10k.

I have compiled the following issues that need to address to enable the mesh support:

1. Beacon Filtering
Currenly, adhoc mode only allowed the beacon with the BSSID set by the ath10k_wmi_vdev_up to pass to mac80211. Continuous background scanning may not be good since we need to receive the beacon for synchronization purpose. FYI, mesh uses the BSSID similar to its own vif mac addr.

2. QoS Data Frame for broadcast data frame
Currently, only non-QoS data allowed for broadcast frame as I observed.

3. QoS Control Field, no stripped off
We need to set the bit-8 of QoS control field to indicate the presence of mesh control field.

I believe that we need to have some changes on the Firmware to make this work.

Please kindly let me know is that possible to make arrangement of FW changes.

Thanks

Regards,
Chun-Yeow

Quoted 20 lines · Ben Greear

Anyone know what it would take to get ath10k to support 802.11s?

As you know, I'm not above modifying ath10k firmware, but I also do not have a huge amount of time to put into this, so if changes needed are extensive, then probably I cannot do it now...

Thanks,
Ben

--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k