Skip to contentSkip to conversation

Confusing error

DISCUSSION Gary Thomas 2 participants 3 messages May 5, 2015

lore
Share & tools
lore
#0 lore raw

I'm getting a very confusing error from bitbake. I'm using a snapshot from Poky/Yocto (equivalent to 1.8 release) with my own $DISTRO

  $ bitbake nand-installer-image
  NOTE: Started PRServer with DBfile: /home/gary/tmp/p0381_2015-05-05/p0381_build/cache/prserv.sqlite3, IP: 127.0.0.1, PORT: 41585, PID: 460
  Loading cache: 100% |###################################################################################| ETA:  00:00:00
  Loaded 1708 entries from dependency cache.
  NOTE: Resolving any missing task queue dependencies
  ERROR: Nothing RPROVIDES 'virtual/bootloader' (but /home/gary/tmp/p0381_2015-05-05/opt/amltd/poky/meta-amltd/packages/packagegroups /packagegroup-amltd.bb RDEPENDS on or 
otherwise requires it)
  NOTE: Runtime target 'virtual/bootloader' is unbuildable, removing...
  Missing or unbuildable dependency chain was: ['virtual/bootloader']
  NOTE: Runtime target 'packagegroup-amltd-boot' is unbuildable, removing...
  Missing or unbuildable dependency chain was: ['packagegroup-amltd-boot', 'virtual/bootloader']
  ERROR: Required build target 'nand-installer-image' has no buildable providers.
  Missing or unbuildable dependency chain was: ['nand-installer-image', 'packagegroup-amltd-boot', 'virtual/bootloader']

But, there is such a provider and I can build it (from the same build tree):

  $ bitbake virtual/bootloader
  NOTE: Started PRServer with DBfile: /home/gary/tmp/p0381_2015-05-05/p0381_build/cache/prserv.sqlite3, IP: 127.0.0.1, PORT: 43428, PID: 515
  Loading cache: 100% |###################################################################################| ETA:  00:00:00
  Loaded 1708 entries from dependency cache.
  NOTE: Resolving any missing task queue dependencies

Build Configuration:

  BB_VERSION        = "1.27.0"
  BUILD_SYS         = "i686-linux"
  NATIVELSBSTRING   = "Fedora-17"
  TARGET_SYS        = "arm-amltd-linux-gnueabi"
  MACHINE           = "teton-p0381"
  DISTRO            = "amltd"
  DISTRO_VERSION    = "1.8+snapshot-2015-05-05"
  TUNE_FEATURES     = "arm armv7a vfp neon callconvention-hard cortexa7"
  TARGET_FPU        = "vfp-neon"

meta
meta-oe
meta-amltd
meta-teton-ls1-p0381
meta-fsl-arm
meta-fsl-arm-extra
meta-browser = "<unknown>:<unknown>"

NOTE: Preparing RunQueue
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks

        ...

After much research, I found that this is happening because I have
MACHINE_EXTRA_RRECOMMENDS="virtual/bootloader linux-firmware-iwlwifi-5xxx"

If I remove the 'virtual/bootloader' from MACHINE_EXTRA_RRECOMMENDS, the confusion (and error) go away. Any ideas what's happening and why I might be getting this confusing error?

Thanks

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#1 lore raw

Hi Gary,

Quoted 54 lines · On Tuesday 05 May 2015 08:44:47 Gary Thomas wrote:

I'm getting a very confusing error from bitbake. I'm using a snapshot from Poky/Yocto (equivalent to 1.8 release) with my own $DISTRO

   $ bitbake nand-installer-image
   NOTE: Started PRServer with DBfile:
/home/gary/tmp/p0381_2015-05-05/p0381_build/cache/prserv.sqlite3, IP:
127.0.0.1, PORT: 41585, PID: 460 Loading cache: 100%
|##########################################################################
#########| ETA:  00:00:00 Loaded 1708 entries from dependency cache.
   NOTE: Resolving any missing task queue dependencies
   ERROR: Nothing RPROVIDES 'virtual/bootloader' (but
/home/gary/tmp/p0381_2015-05-05/opt/amltd/poky/meta-amltd/packages/packageg
roups /packagegroup-amltd.bb RDEPENDS on or otherwise requires it)
   NOTE: Runtime target 'virtual/bootloader' is unbuildable, removing...
   Missing or unbuildable dependency chain was: ['virtual/bootloader']
   NOTE: Runtime target 'packagegroup-amltd-boot' is unbuildable,
removing... Missing or unbuildable dependency chain was:
['packagegroup-amltd-boot', 'virtual/bootloader'] ERROR: Required build
target 'nand-installer-image' has no buildable providers. Missing or
unbuildable dependency chain was: ['nand-installer-image',
'packagegroup-amltd-boot', 'virtual/bootloader']

But, there is such a provider and I can build it (from the same build tree):

$ bitbake virtual/bootloader
   NOTE: Started PRServer with DBfile:
/home/gary/tmp/p0381_2015-05-05/p0381_build/cache/prserv.sqlite3, IP:
127.0.0.1, PORT: 43428, PID: 515 Loading cache: 100%
|##########################################################################
#########| ETA:  00:00:00 Loaded 1708 entries from dependency cache.
   NOTE: Resolving any missing task queue dependencies

Build Configuration:

   BB_VERSION        = "1.27.0"
   BUILD_SYS         = "i686-linux"
   NATIVELSBSTRING   = "Fedora-17"
   TARGET_SYS        = "arm-amltd-linux-gnueabi"
   MACHINE           = "teton-p0381"
   DISTRO            = "amltd"
   DISTRO_VERSION    = "1.8+snapshot-2015-05-05"
   TUNE_FEATURES     = "arm armv7a vfp neon callconvention-hard cortexa7"
   TARGET_FPU        = "vfp-neon"

meta
meta-oe
meta-amltd
meta-teton-ls1-p0381
meta-fsl-arm
meta-fsl-arm-extra
meta-browser = "<unknown>:<unknown>"

NOTE: Preparing RunQueue
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks

         ...
Quoted 7 lines

After much research, I found that this is happening because I have
MACHINE_EXTRA_RRECOMMENDS="virtual/bootloader
linux-firmware-iwlwifi-5xxx"

If I remove the 'virtual/bootloader' from MACHINE_EXTRA_RRECOMMENDS, the confusion (and error) go away. Any ideas what's happening and why I might be getting this confusing error?

The confusion here is between runtime targets (package names, i.e. what you should specify in MACHINE_EXTRA_RRECOMMENDS) and build-time targets e.g. virtual/bootloader. virtual/bootloader is not a runtime target (hence "Nothing RPROVIDES ..." and thus doesn't belong in MACHINE_EXTRA_RRECOMMENDS. I suspect what you want instead is:

EXTRA_IMAGEDEPENDS += "virtual/bootloader"

Cheers,
Paul

Signature · 2 lines
Paul Eggleton
Intel Open Source Technology Centre
#2 lore raw
Quoted 65 lines · Paul Eggleton

Hi Gary,

Quoted 54 lines · On Tuesday 05 May 2015 08:44:47 Gary Thomas wrote:

I'm getting a very confusing error from bitbake. I'm using a snapshot from Poky/Yocto (equivalent to 1.8 release) with my own $DISTRO

    $ bitbake nand-installer-image
    NOTE: Started PRServer with DBfile:
/home/gary/tmp/p0381_2015-05-05/p0381_build/cache/prserv.sqlite3, IP:
127.0.0.1, PORT: 41585, PID: 460 Loading cache: 100%
|##########################################################################
#########| ETA:  00:00:00 Loaded 1708 entries from dependency cache.
    NOTE: Resolving any missing task queue dependencies
    ERROR: Nothing RPROVIDES 'virtual/bootloader' (but
/home/gary/tmp/p0381_2015-05-05/opt/amltd/poky/meta-amltd/packages/packageg
roups /packagegroup-amltd.bb RDEPENDS on or otherwise requires it)
    NOTE: Runtime target 'virtual/bootloader' is unbuildable, removing...
    Missing or unbuildable dependency chain was: ['virtual/bootloader']
    NOTE: Runtime target 'packagegroup-amltd-boot' is unbuildable,
removing... Missing or unbuildable dependency chain was:
['packagegroup-amltd-boot', 'virtual/bootloader'] ERROR: Required build
target 'nand-installer-image' has no buildable providers. Missing or
unbuildable dependency chain was: ['nand-installer-image',
'packagegroup-amltd-boot', 'virtual/bootloader']

But, there is such a provider and I can build it (from the same build tree):

$ bitbake virtual/bootloader
    NOTE: Started PRServer with DBfile:
/home/gary/tmp/p0381_2015-05-05/p0381_build/cache/prserv.sqlite3, IP:
127.0.0.1, PORT: 43428, PID: 515 Loading cache: 100%
|##########################################################################
#########| ETA:  00:00:00 Loaded 1708 entries from dependency cache.
    NOTE: Resolving any missing task queue dependencies

Build Configuration:
BB_VERSION = "1.27.0"
BUILD_SYS = "i686-linux"
NATIVELSBSTRING = "Fedora-17"
TARGET_SYS = "arm-amltd-linux-gnueabi"
MACHINE = "teton-p0381"
DISTRO = "amltd"
DISTRO_VERSION = "1.8+snapshot-2015-05-05"
TUNE_FEATURES = "arm armv7a vfp neon callconvention-hard cortexa7"
TARGET_FPU = "vfp-neon"
meta
meta-oe
meta-amltd
meta-teton-ls1-p0381
meta-fsl-arm
meta-fsl-arm-extra
meta-browser = "<unknown>:<unknown>"

NOTE: Preparing RunQueue
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
...

Quoted 7 lines

After much research, I found that this is happening because I have
MACHINE_EXTRA_RRECOMMENDS="virtual/bootloader
linux-firmware-iwlwifi-5xxx"

If I remove the 'virtual/bootloader' from MACHINE_EXTRA_RRECOMMENDS, the confusion (and error) go away. Any ideas what's happening and why I might be getting this confusing error?

Quoted 7 lines

The confusion here is between runtime targets (package names, i.e. what you should specify in MACHINE_EXTRA_RRECOMMENDS) and build-time targets e.g. virtual/bootloader. virtual/bootloader is not a runtime target (hence "Nothing RPROVIDES ..." and thus doesn't belong in MACHINE_EXTRA_RRECOMMENDS. I suspect what you want instead is:

EXTRA_IMAGEDEPENDS += "virtual/bootloader"

Thanks for the explanation, that fixes my problem.

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------