Skip to contentSkip to conversation

Question on bssid mask with ath10k

DISCUSSION Jose Núñez-Martínez (CTTC) 3 participants 10 messages Jul 3, 2015 – Jul 6, 2015 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

Jose

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#2 lore raw

Hi,
I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 from CT and Firmware is 10.1.467-ct-com-full-014-96d543 However I cannot bring up two virtal interfaces associated to one physical device.

The output of "iw dev" command:

phy#1

    Interface moni2
        ifindex 9
        wdev 0x100000002
        addr 04:f0:21:18:26:a5
        type managed
    Interface wlan2
        ifindex 7
        wdev 0x100000001
        addr 04:f0:21:18:26:a5
        type IBSS

This is the error shown when I try to bring up moni2 interface (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"

Jose

Quoted 25 lines · Michal Kazior
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 14 lines
Jose Núñez-Martínez, PhD
Researcher               email: [email protected]
COMNET Division     Web: http://networks.cttc.cat

Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
Parc Mediterrani de la Tecnologia
Av. Carl Friedrich Gauss, 7                Ph.:+34 936452927
08860 Castelldefels - Barcelona            Fax: +34 936452901


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#3 lore raw
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Hi,
I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 from CT and Firmware is 10.1.467-ct-com-full-014-96d543 However I cannot bring up two virtal interfaces associated to one physical device.

Quoted 8 lines

The output of "iw dev" command:

phy#1

     Interface moni2
         ifindex 9
         wdev 0x100000002
         addr 04:f0:21:18:26:a5
         type managed

It is type managed...you created this wrong somehow.

If you want to bring up more than one managed interface, you have to change the MAC address first so that they are unique.

Thanks,
Ben

Quoted 38 lines
     Interface wlan2
         ifindex 7
         wdev 0x100000001
         addr 04:f0:21:18:26:a5
         type IBSS

This is the error shown when I try to bring up moni2 interface (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"

Jose

Quoted 25 lines · Michal Kazior
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#4 lore raw

Thanks for your answer. My goal was to create a monitor interface (mon2) and another (wlan2) in ibss mode associated to the same physical device. This is the command I tried to create a virtual interface associated to phy0 in monitor mode:

iw phy phy0 interface add moni2 type monitor

As you mentioned it is somehow configured as "managed" and not as monitor. Any ideas?

Jose

Quoted 63 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Hi,
I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 from CT and Firmware is 10.1.467-ct-com-full-014-96d543 However I cannot bring up two virtal interfaces associated to one physical device.

Quoted 8 lines

The output of "iw dev" command:

phy#1

     Interface moni2
         ifindex 9
         wdev 0x100000002
         addr 04:f0:21:18:26:a5
         type managed

It is type managed...you created this wrong somehow.

If you want to bring up more than one managed interface, you have to change the MAC address first so that they are unique.

Thanks,
Ben

Quoted 38 lines
     Interface wlan2
         ifindex 7
         wdev 0x100000001
         addr 04:f0:21:18:26:a5
         type IBSS

This is the error shown when I try to bring up moni2 interface (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"

Jose

Quoted 25 lines · Michal Kazior
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 14 lines
Jose Núñez-Martínez, PhD
Researcher               email: [email protected]
COMNET Division     Web: http://networks.cttc.cat

Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
Parc Mediterrani de la Tecnologia
Av. Carl Friedrich Gauss, 7                Ph.:+34 936452927
08860 Castelldefels - Barcelona            Fax: +34 936452901


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#5 lore raw
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Thanks for your answer. My goal was to create a monitor interface (mon2) and another (wlan2) in ibss mode associated to the same physical device. This is the command I tried to create a virtual interface associated to phy0 in monitor mode:

iw phy phy0 interface add moni2 type monitor

That looks right...that command works for me. Maybe you already had moni2 created incorrectly? Try starting from fresh reboot or driver reload?

Also, you should not actually need a monitor dev to have CT firmware work properly...but of course if you want to sniff frames, it can be useful.

Thanks,
Ben

Quoted 70 lines

As you mentioned it is somehow configured as "managed" and not as monitor. Any ideas?

Jose

Quoted 63 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Hi,
I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 from CT and Firmware is 10.1.467-ct-com-full-014-96d543 However I cannot bring up two virtal interfaces associated to one physical device.

Quoted 8 lines

The output of "iw dev" command:

phy#1

     Interface moni2
         ifindex 9
         wdev 0x100000002
         addr 04:f0:21:18:26:a5
         type managed

It is type managed...you created this wrong somehow.

If you want to bring up more than one managed interface, you have to change the MAC address first so that they are unique.

Thanks,
Ben

Quoted 38 lines
     Interface wlan2
         ifindex 7
         wdev 0x100000001
         addr 04:f0:21:18:26:a5
         type IBSS

This is the error shown when I try to bring up moni2 interface (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"

Jose

Quoted 25 lines · Michal Kazior
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#6 lore raw

Hi,
the reason for starting a virtual device in monitor mode is to infuence Rx filters in firmware as pointed out in [1]. The goal is to configure the wireless device in adhoc mode so that it can receive and send packets containing any mac destination address.

[1] http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Thx,
Jose

Quoted 10 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Thanks for your answer. My goal was to create a monitor interface (mon2) and another (wlan2) in ibss mode associated to the same physical device. This is the command I tried to create a virtual interface associated to phy0 in monitor mode:

iw phy phy0 interface add moni2 type monitor

That looks right...that command works for me. Maybe you already had moni2 created incorrectly? Try starting from fresh reboot or driver reload?

Quoted 78 lines

Also, you should not actually need a monitor dev to have CT firmware work properly...but of course if you want to sniff frames, it can be useful.

Thanks,
Ben

Quoted 70 lines

As you mentioned it is somehow configured as "managed" and not as monitor. Any ideas?

Jose

Quoted 63 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Hi,
I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 from CT and Firmware is 10.1.467-ct-com-full-014-96d543 However I cannot bring up two virtal interfaces associated to one physical device.

Quoted 8 lines

The output of "iw dev" command:

phy#1

     Interface moni2
         ifindex 9
         wdev 0x100000002
         addr 04:f0:21:18:26:a5
         type managed

It is type managed...you created this wrong somehow.

If you want to bring up more than one managed interface, you have to change the MAC address first so that they are unique.

Thanks,
Ben

Quoted 38 lines
     Interface wlan2
         ifindex 7
         wdev 0x100000001
         addr 04:f0:21:18:26:a5
         type IBSS

This is the error shown when I try to bring up moni2 interface (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"

Jose

Quoted 25 lines · Michal Kazior
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#7 lore raw
Quoted 5 lines · Jose Núñez-Martínez (CTTC)

Hi,
the reason for starting a virtual device in monitor mode is to infuence Rx filters in firmware as pointed out in [1]. The goal is to configure the wireless device in adhoc mode so that it can receive and send packets containing any mac destination address.

[1] http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

BSSID mask is not your main problem I think. It is primarily used to deal with multiple virtual devices (ap, STA, IBSS). PROMISC will effectively just disable the BSSID mask so that all (most, really..monitor mode is not perfect for ath10k) frames are passed up the stack to the host.

The firmware will not send packets to destinations that it does not have a peer object for, so you will not be able to transmit to arbitrary destinations.

ADHOC will create peer objects as it associates with new peers, so maybe you do not actually need 'any mac destination address'?

I have some bugs to track down relating to some .11r and/or ANQP failures that we see in some of our tests...possibly I'll figure out how to send to arbitrary destinations while fixing this.

ath10k is full of subtle and not-so-subtle limitations. I think for best support you should spell out your real goals and use cases in detail instead of trying to think of ath10k as just a faster version of ath9k.

Thanks,
Ben

Quoted 95 lines

Thx,
Jose

Quoted 88 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Thanks for your answer. My goal was to create a monitor interface (mon2) and another (wlan2) in ibss mode associated to the same physical device. This is the command I tried to create a virtual interface associated to phy0 in monitor mode:

iw phy phy0 interface add moni2 type monitor

That looks right...that command works for me. Maybe you already had moni2 created incorrectly? Try starting from fresh reboot or driver reload?

Also, you should not actually need a monitor dev to have CT firmware work properly...but of course if you want to sniff frames, it can be useful.

Thanks,
Ben

Quoted 70 lines

As you mentioned it is somehow configured as "managed" and not as monitor. Any ideas?

Jose

Quoted 63 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Hi,
I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 from CT and Firmware is 10.1.467-ct-com-full-014-96d543 However I cannot bring up two virtal interfaces associated to one physical device.

Quoted 8 lines

The output of "iw dev" command:

phy#1

     Interface moni2
         ifindex 9
         wdev 0x100000002
         addr 04:f0:21:18:26:a5
         type managed

It is type managed...you created this wrong somehow.

If you want to bring up more than one managed interface, you have to change the MAC address first so that they are unique.

Thanks,
Ben

Quoted 38 lines
     Interface wlan2
         ifindex 7
         wdev 0x100000001
         addr 04:f0:21:18:26:a5
         type IBSS

This is the error shown when I try to bring up moni2 interface (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"

Jose

Quoted 25 lines · Michal Kazior
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#8 lore raw
Quoted 18 lines · Ben Greear
Quoted 5 lines · Jose Núñez-Martínez (CTTC)

Hi,
the reason for starting a virtual device in monitor mode is to infuence Rx filters in firmware as pointed out in [1]. The goal is to configure the wireless device in adhoc mode so that it can receive and send packets containing any mac destination address.

[1] http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

BSSID mask is not your main problem I think. It is primarily used to deal with multiple virtual devices (ap, STA, IBSS). PROMISC will effectively just disable the BSSID mask so that all (most, really..monitor mode is not perfect for ath10k) frames are passed up the stack to the host.

The firmware will not send packets to destinations that it does not have a peer object for, so you will not be able to transmit to arbitrary destinations.

ADHOC will create peer objects as it associates with new peers, so maybe you do not actually need 'any mac destination address'?

Quoted 7 lines

I have some bugs to track down relating to some .11r and/or ANQP failures that we see in some of our tests...possibly I'll figure out how to send to arbitrary destinations while fixing this.

ath10k is full of subtle and not-so-subtle limitations. I think for best support you should spell out your real goals and use cases in detail instead of trying to think of ath10k as just a faster version of ath9k.

Well, the goal is to use of 802.11ac cards acting as ports of virtual switches such as xDPd [1]. A primary use case I'm testing is to send traffic between two hosts connected through two virtual switches. Virtual switches are installed on different nodes and are wirelessly interconnected through two 802.11ac cards. Each of these cards is acting as a wireless port in each virtual switch.

To receive and send any traffic in the virtual switches I need PROMISC enabled in the wireless ports but cards are dropping packets that are not directed to their MAC dst address of the wireless ports.

Hope that gives some context to understand the problem I'm facing.

[1] http://xdpd.org/

Thanks,
Jose

Quoted 101 lines

Thanks,
Ben

Quoted 95 lines

Thx,
Jose

Quoted 88 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Thanks for your answer. My goal was to create a monitor interface (mon2) and another (wlan2) in ibss mode associated to the same physical device. This is the command I tried to create a virtual interface associated to phy0 in monitor mode:

iw phy phy0 interface add moni2 type monitor

That looks right...that command works for me. Maybe you already had moni2 created incorrectly? Try starting from fresh reboot or driver reload?

Also, you should not actually need a monitor dev to have CT firmware work properly...but of course if you want to sniff frames, it can be useful.

Thanks,
Ben

Quoted 70 lines

As you mentioned it is somehow configured as "managed" and not as monitor. Any ideas?

Jose

Quoted 63 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Hi,
I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 from CT and Firmware is 10.1.467-ct-com-full-014-96d543 However I cannot bring up two virtal interfaces associated to one physical device.

Quoted 8 lines

The output of "iw dev" command:

phy#1

     Interface moni2
         ifindex 9
         wdev 0x100000002
         addr 04:f0:21:18:26:a5
         type managed

It is type managed...you created this wrong somehow.

If you want to bring up more than one managed interface, you have to change the MAC address first so that they are unique.

Thanks,
Ben

Quoted 38 lines
     Interface wlan2
         ifindex 7
         wdev 0x100000001
         addr 04:f0:21:18:26:a5
         type IBSS

This is the error shown when I try to bring up moni2 interface (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"

Jose

Quoted 25 lines · Michal Kazior
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 14 lines
Jose Núñez-Martínez, PhD
Researcher               email: [email protected]
COMNET Division     Web: http://networks.cttc.cat

Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
Parc Mediterrani de la Tecnologia
Av. Carl Friedrich Gauss, 7                Ph.:+34 936452927
08860 Castelldefels - Barcelona            Fax: +34 936452901


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#9 lore raw
Quoted 29 lines · Jose Núñez-Martínez (CTTC)
Quoted 18 lines · Ben Greear
Quoted 5 lines · Jose Núñez-Martínez (CTTC)

Hi,
the reason for starting a virtual device in monitor mode is to infuence Rx filters in firmware as pointed out in [1]. The goal is to configure the wireless device in adhoc mode so that it can receive and send packets containing any mac destination address.

[1] http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

BSSID mask is not your main problem I think. It is primarily used to deal with multiple virtual devices (ap, STA, IBSS). PROMISC will effectively just disable the BSSID mask so that all (most, really..monitor mode is not perfect for ath10k) frames are passed up the stack to the host.

The firmware will not send packets to destinations that it does not have a peer object for, so you will not be able to transmit to arbitrary destinations.

ADHOC will create peer objects as it associates with new peers, so maybe you do not actually need 'any mac destination address'?

Quoted 7 lines

I have some bugs to track down relating to some .11r and/or ANQP failures that we see in some of our tests...possibly I'll figure out how to send to arbitrary destinations while fixing this.

ath10k is full of subtle and not-so-subtle limitations. I think for best support you should spell out your real goals and use cases in detail instead of trying to think of ath10k as just a faster version of ath9k.

Quoted 6 lines

Well, the goal is to use of 802.11ac cards acting as ports of virtual switches such as xDPd [1]. A primary use case I'm testing is to send traffic between two hosts connected through two virtual switches. Virtual switches are installed on different nodes and are wirelessly interconnected through two 802.11ac cards. Each of these cards is acting as a wireless port in each virtual switch.

To receive and send any traffic in the virtual switches I need PROMISC enabled in the wireless ports but cards are dropping packets that are not directed to their MAC dst address of the wireless ports.

Maybe have the two wireless NICs talk to each other using IBSS, and then encapsulate the bridged frames inside of the wifi packets using some hack of a VPN or something like that?

PROMISC mode in CT firmware should allow RX of frames, but I don't think there is any way to TX the frames as you are trying to do.

Thanks,
Ben

Quoted 110 lines

Hope that gives some context to understand the problem I'm facing.

[1] http://xdpd.org/

Thanks,
Jose

Quoted 101 lines

Thanks,
Ben

Quoted 95 lines

Thx,
Jose

Quoted 88 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Thanks for your answer. My goal was to create a monitor interface (mon2) and another (wlan2) in ibss mode associated to the same physical device. This is the command I tried to create a virtual interface associated to phy0 in monitor mode:

iw phy phy0 interface add moni2 type monitor

That looks right...that command works for me. Maybe you already had moni2 created incorrectly? Try starting from fresh reboot or driver reload?

Also, you should not actually need a monitor dev to have CT firmware work properly...but of course if you want to sniff frames, it can be useful.

Thanks,
Ben

Quoted 70 lines

As you mentioned it is somehow configured as "managed" and not as monitor. Any ideas?

Jose

Quoted 63 lines · Ben Greear
Quoted 4 lines · Jose Núñez-Martínez (CTTC)

Hi,
I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 from CT and Firmware is 10.1.467-ct-com-full-014-96d543 However I cannot bring up two virtal interfaces associated to one physical device.

Quoted 8 lines

The output of "iw dev" command:

phy#1

     Interface moni2
         ifindex 9
         wdev 0x100000002
         addr 04:f0:21:18:26:a5
         type managed

It is type managed...you created this wrong somehow.

If you want to bring up more than one managed interface, you have to change the MAC address first so that they are unique.

Thanks,
Ben

Quoted 38 lines
     Interface wlan2
         ifindex 7
         wdev 0x100000001
         addr 04:f0:21:18:26:a5
         type IBSS

This is the error shown when I try to bring up moni2 interface (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"

Jose

Quoted 25 lines · Michal Kazior
Quoted 8 lines · Jose Núñez-Martínez (CTTC)

I'm trying to set BSSID mask in ath10k so that data packets with spoofed mac destination address can be received (and not dropped) by the card.

Apparently the way bssid mask is managed has changed from ath5k and ath9k since there are not "ath5k_hw_set_bssid_mask" or "ath9k_htc_set_mac_bssid_mask" kind of functions.

Anyone tried this?

There's no explicit control over Rx filters in ath10k that I know of. This is abstracted away by other firmware higher-level commands. One way to influence Rx filter (and BSSID mask) is to start a monitor vdev in firmware. This apparently works[1] but 636 will crash on you again if you do that. You'll need Ben's CT firmware.

[1]: http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k