Skip to contentSkip to conversation

Rane SL-4 USB sound card

DISCUSSION Tuukka Pasanen 2 participants 11 messages Jul 4, 2015 – Jul 7, 2015

lore
Share & tools
lore
#0 lore raw

Hello,
I've been hacking to get Rane SL-4 USB audio (http://dj.rane.com/products/sl4-for-serato-scratch-live) which have 4 Input and 4 output channel to work with ALSA. After digging the lsusb and snoops I have separated endpoints for input (0x82) and output (0x06). They are just USB Isochronous I/O. I have compiled kernel and tried to get USB-quirks to work with this but then I have to admit that even Reloop Play seems be very similar it doesn't do the trick (No error but card doesn't come up eather) nor using Ranel SL-1 approach which just shoots the error

[ 3555.009349] usb 1-5: Audio class v2 interfaces need an interface association
[ 3555.009373] snd-usb-audio: probe of 1-5:1.0 failed with error -5
[ 3555.009394] usb 1-5: cannot find UAC_HEADER
[ 3555.009401] snd-usb-audio: probe of 1-5:1.1 failed with error -5
[ 3555.009421] usb 1-5: cannot find UAC_HEADER
[ 3555.009427] snd-usb-audio: probe of 1-5:1.2 failed with error -5

If I need interface association how to do that? Trying to adjust mixer values in mixer_maps.c.

If someone have a time to give some guidance if this doable with Quirks or do I have to write some more specific driver? I attach lsusb below here. HID device seems to be adjusting buffer size and 48 Khz and 96 Khz output.

Bus 001 Device 003: ID 1cc5:000f
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 255
bDeviceProtocol 255
bMaxPacketSize0 64
idVendor 0x1cc5
idProduct 0x000f
bcdDevice 1.00

  iManufacturer           1 Rane Corporation
  iProduct                2 Rane SL 4
  iSerial                 3 RH.01.00
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 235
bNumInterfaces 4
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 1
bInterfaceProtocol 32
iInterface 4 SL 4 Audio
** UNRECOGNIZED: 09 24 01 00 02 0a 4b 00 00
** UNRECOGNIZED: 08 24 0a 05 01 01 00 00
** UNRECOGNIZED: 11 24 02 01 01 01 00 05 0a 00 00 00 00 05 00 00 00 ** UNRECOGNIZED: 0c 24 03 02 02 06 00 01 05 00 00 00
** UNRECOGNIZED: 11 24 02 03 02 06 00 05 0a 00 00 00 00 0f 00 00 00 ** UNRECOGNIZED: 0c 24 03 04 01 01 00 03 05 00 00 00
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 2
bInterfaceProtocol 32
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 1
bNumEndpoints 1
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 2
bInterfaceProtocol 32
iInterface 0
** UNRECOGNIZED: 10 24 01 01 00 01 01 00 00 00 0a 00 00 00 00 05 ** UNRECOGNIZED: 06 24 02 01 04 18
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 5
Transfer Type Isochronous
Synch Type Asynchronous
Usage Type Data
wMaxPacketSize 0x0208 1x 520 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 2
bInterfaceProtocol 32
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 1
bNumEndpoints 1
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 2
bInterfaceProtocol 32
iInterface 0
** UNRECOGNIZED: 10 24 01 03 00 01 01 00 00 00 0a 00 00 00 00 0f ** UNRECOGNIZED: 06 24 02 01 04 18
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 37
Transfer Type Isochronous
Synch Type Asynchronous
Usage Type Implicit feedback Data
wMaxPacketSize 0x0208 1x 520 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 28
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 255
bDeviceProtocol 255
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)

Thanks you for your time and any tips would be nice.

Sincerely,
Tuukka

#1 lore raw
Quoted 4 lines · Tuukka Pasanen

I've been hacking to get Rane SL-4 USB audio ... to work with ALSA.
I have compiled kernel and tried to get USB-quirks to work with this ... it doesn't do the trick

If I need interface association how to do that?

The interface association descriptor should have been provided by the firmware.

Anyway, try the following quirk:

{
	USB_DEVICE(0x1cc5, 0x000f),
	.driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
		.ifnum = QUIRK_ANY_INTERFACE,
		.type = QUIRK_COMPOSITE,
		.data = (const struct snd_usb_audio_quirk[]) {
			{
				.ifnum = 1,
				.type = QUIRK_AUDIO_STANDARD_INTERFACE
			},
			{
				.ifnum = 2,
				.type = QUIRK_AUDIO_STANDARD_INTERFACE
			},
			{
				.ifnum = -1,
			}
		}
	}
},

Regards,
Clemens

#2 lore raw

Hello,
Thanks you for you reply. That did the trick almost. It only gives sysdefault with two channels and error:

[176317.418587] usb 1-5: parse_audio_format_rates_v2(): unable to retrieve number of sample rates (clock 5)
[176317.419156] usb 1-5: parse_audio_format_rates_v2(): unable to retrieve number of sample rates (clock 5)

I figured out this kind of QUIRK which seems to be working (go to test tomorrow more). I would go with first quirck as it's looking simpler but I can't add rates to it?

{
    USB_DEVICE(0x1cc5, 0x000f),
    .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
        .ifnum = QUIRK_ANY_INTERFACE,
        .type = QUIRK_COMPOSITE,
        .data = (const struct snd_usb_audio_quirk[]) {
            {
                .ifnum = 1,
                .type = QUIRK_AUDIO_FIXED_ENDPOINT,
                .data = &(const struct audioformat) {
                    .formats = SNDRV_PCM_FMTBIT_S24_3LE,
                    .channels = 4,
                    .iface = 1,
                    .altsetting = 1,
                    .altset_idx = 1,
                    .attributes = UAC_EP_CS_ATTR_SAMPLE_RATE,
                    .endpoint = 0x06,
                    .ep_attr = USB_ENDPOINT_XFER_ISOC,
                    .rates = SNDRV_PCM_RATE_48000 |
                         SNDRV_PCM_RATE_96000,
                    .rate_min = 48000,
                    .rate_max = 96000,
                    .nr_rates = 2,
                    .rate_table = (unsigned int[]) {
                        48000, 96000
                    }
                }
            },
            {
                .ifnum = 2,
                .type = QUIRK_AUDIO_FIXED_ENDPOINT,
                .data = &(const struct audioformat) {
                    .formats = SNDRV_PCM_FMTBIT_S24_3LE,
                    .channels = 4,
                    .iface = 2,
                    .altsetting = 1,
                    .altset_idx = 1,
                    .attributes = UAC_EP_CS_ATTR_SAMPLE_RATE,
                    .endpoint = 0x82,
                    .ep_attr = USB_ENDPOINT_XFER_ISOC,
                    .rates = SNDRV_PCM_RATE_48000 |
                         SNDRV_PCM_RATE_96000,
                    .rate_min = 48000,
                    .rate_max = 96000,
                    .nr_rates = 2,
                    .rate_table = (unsigned int[]) {
                        48000, 96000
                    }
                }
            },
            {
                .ifnum = -1,
            }
        }
    }
},

Sincerely,
Tuukka

05.07.2015, 20:32, Clemens Ladisch kirjoitti:

Quoted 32 lines
Quoted 3 lines · Tuukka Pasanen

I've been hacking to get Rane SL-4 USB audio ... to work with ALSA.
I have compiled kernel and tried to get USB-quirks to work with this ... it doesn't do the trick If I need interface association how to do that?

The interface association descriptor should have been provided by the firmware.

Anyway, try the following quirk:

{
	USB_DEVICE(0x1cc5, 0x000f),
	.driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
		.ifnum = QUIRK_ANY_INTERFACE,
		.type = QUIRK_COMPOSITE,
		.data = (const struct snd_usb_audio_quirk[]) {
			{
				.ifnum = 1,
				.type = QUIRK_AUDIO_STANDARD_INTERFACE
			},
			{
				.ifnum = 2,
				.type = QUIRK_AUDIO_STANDARD_INTERFACE
			},
			{
				.ifnum = -1,
			}
		}
	}
},

Regards,
Clemens

#3 lore raw
In reply to Clemens Ladisch

Hello,
Thanks you for you reply. That did the trick almost. It only gives sysdefault with two channels and error:

[176317.418587] usb 1-5: parse_audio_format_rates_v2(): unable to retrieve number of sample rates (clock 5)
[176317.419156] usb 1-5: parse_audio_format_rates_v2(): unable to retrieve number of sample rates (clock 5)

I figured out this kind of QUIRK which seems to be working (go to test tomorrow more). I would go with first quirck as it's looking simpler but I can't add rates to it?

{
    USB_DEVICE(0x1cc5, 0x000f),
    .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
        .ifnum = QUIRK_ANY_INTERFACE,
        .type = QUIRK_COMPOSITE,
        .data = (const struct snd_usb_audio_quirk[]) {
            {
                .ifnum = 1,
                .type = QUIRK_AUDIO_FIXED_ENDPOINT,
                .data = &(const struct audioformat) {
                    .formats = SNDRV_PCM_FMTBIT_S24_3LE,
                    .channels = 4,
                    .iface = 1,
                    .altsetting = 1,
                    .altset_idx = 1,
                    .attributes = UAC_EP_CS_ATTR_SAMPLE_RATE,
                    .endpoint = 0x06,
                    .ep_attr = USB_ENDPOINT_XFER_ISOC,
                    .rates = SNDRV_PCM_RATE_48000 |
                         SNDRV_PCM_RATE_96000,
                    .rate_min = 48000,
                    .rate_max = 96000,
                    .nr_rates = 2,
                    .rate_table = (unsigned int[]) {
                        48000, 96000
                    }
                }
            },
            {
                .ifnum = 2,
                .type = QUIRK_AUDIO_FIXED_ENDPOINT,
                .data = &(const struct audioformat) {
                    .formats = SNDRV_PCM_FMTBIT_S24_3LE,
                    .channels = 4,
                    .iface = 2,
                    .altsetting = 1,
                    .altset_idx = 1,
                    .attributes = UAC_EP_CS_ATTR_SAMPLE_RATE,
                    .endpoint = 0x82,
                    .ep_attr = USB_ENDPOINT_XFER_ISOC,
                    .rates = SNDRV_PCM_RATE_48000 |
                         SNDRV_PCM_RATE_96000,
                    .rate_min = 48000,
                    .rate_max = 96000,
                    .nr_rates = 2,
                    .rate_table = (unsigned int[]) {
                        48000, 96000
                    }
                }
            },
            {
                .ifnum = -1,
            }
        }
    }
},

Sincerely,
Tuukka

05.07.2015, 20:32, Clemens Ladisch kirjoitti:

Quoted 32 lines
Quoted 3 lines · Tuukka Pasanen

I've been hacking to get Rane SL-4 USB audio ... to work with ALSA.
I have compiled kernel and tried to get USB-quirks to work with this ... it doesn't do the trick If I need interface association how to do that?

The interface association descriptor should have been provided by the firmware.

Anyway, try the following quirk:

{
	USB_DEVICE(0x1cc5, 0x000f),
	.driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
		.ifnum = QUIRK_ANY_INTERFACE,
		.type = QUIRK_COMPOSITE,
		.data = (const struct snd_usb_audio_quirk[]) {
			{
				.ifnum = 1,
				.type = QUIRK_AUDIO_STANDARD_INTERFACE
			},
			{
				.ifnum = 2,
				.type = QUIRK_AUDIO_STANDARD_INTERFACE
			},
			{
				.ifnum = -1,
			}
		}
	}
},

Regards,
Clemens

#4 lore raw
Quoted 1 line · Tuukka Pasanen
[176317.418587] usb 1-5: parse_audio_format_rates_v2(): unable to retrieve number of sample rates (clock 5)

So it doesn't actually conform with the audio class.

Quoted 1 line

I figured out this kind of QUIRK which seems to be working (go to test tomorrow more).

Hmm, the descriptors claim it uses S24_LE ...

Do all channels work?
Does it correctly switch between 48/96 kHz?
Is it possible to use different rates for playback/capture?

Regards,
Clemens

#5 lore raw

Hello,
Thank you that 24_LE. I'll test tommorrow and find answers to there questions. I'll think that 48/96 won't work because it seems to be behind that HID.. but that this after I get sound out and in.

Tuukka

06.07.2015, 16:07, Clemens Ladisch kirjoitti:

Quoted 14 lines
Quoted 1 line · Tuukka Pasanen
[176317.418587] usb 1-5: parse_audio_format_rates_v2(): unable to retrieve number of sample rates (clock 5)

So it doesn't actually conform with the audio class.

Quoted 1 line

I figured out this kind of QUIRK which seems to be working (go to test tomorrow more).

Hmm, the descriptors claim it uses S24_LE ...

Do all channels work?
Does it correctly switch between 48/96 kHz?
Is it possible to use different rates for playback/capture?

Regards,
Clemens

#6 lore raw
In reply to Clemens Ladisch

Hello,
I've tested Quirck and it worked (at least channels 1-2 input/output) fine when changed S24_LE. Problem is that currently it doesn't have Mixer so pulseaudio or jackd can't see it without .asoundrc. I digged little bit mixer_map.c but didn't get it working.

Sincerely,
Tuukka

06.07.2015, 16:07, Clemens Ladisch kirjoitti:

Quoted 14 lines
Quoted 1 line · Tuukka Pasanen
[176317.418587] usb 1-5: parse_audio_format_rates_v2(): unable to retrieve number of sample rates (clock 5)

So it doesn't actually conform with the audio class.

Quoted 1 line

I figured out this kind of QUIRK which seems to be working (go to test tomorrow more).

Hmm, the descriptors claim it uses S24_LE ...

Do all channels work?
Does it correctly switch between 48/96 kHz?
Is it possible to use different rates for playback/capture?

Regards,
Clemens

#7 lore raw
Quoted 2 lines · Tuukka Pasanen

I've tested Quirck and it worked (at least channels 1-2 input/output) fine when changed S24_LE. Problem is that currently it doesn't have Mixer

According to the descriptors, it does not have mixer controls. Does the Windows driver have mixer controls that affect the hardware?

Quoted 1 line

so pulseaudio or jackd can't see it without .asoundrc.

That should make no difference.

Regards,
Clemens

#8 lore raw

Hello,
No it doesn't. Hmm... I got to examine this more because even Yast2 cant see this or alsaconf..

Tuukka

07.07.2015, 10:23, Clemens Ladisch kirjoitti:

Quoted 12 lines
Quoted 2 lines · Tuukka Pasanen

I've tested Quirck and it worked (at least channels 1-2 input/output) fine when changed S24_LE. Problem is that currently it doesn't have Mixer

According to the descriptors, it does not have mixer controls. Does the Windows driver have mixer controls that affect the hardware?

Quoted 1 line

so pulseaudio or jackd can't see it without .asoundrc.

That should make no difference.

Regards,
Clemens

#9 lore raw
In reply to Clemens Ladisch

Hello,
More digging on this. Pulseaudio and jackd (portaudio) are supporting 24_3LE (Tree byte) that is why they didn't work with 24_LE. Is 24_LE just 32_LE (4 bytes) and first byte is just zeroed? If that is so I can use 32_LE and applications just work?

Sincerely,
Tuukka

07.07.2015, 10:23, Clemens Ladisch kirjoitti:

Quoted 12 lines
Quoted 2 lines · Tuukka Pasanen

I've tested Quirck and it worked (at least channels 1-2 input/output) fine when changed S24_LE. Problem is that currently it doesn't have Mixer

According to the descriptors, it does not have mixer controls. Does the Windows driver have mixer controls that affect the hardware?

Quoted 1 line

so pulseaudio or jackd can't see it without .asoundrc.

That should make no difference.

Regards,
Clemens

#10 lore raw
Quoted 1 line · Tuukka Pasanen

Pulseaudio and jackd (portaudio) are supporting 24_3LE (Tree byte) that is why they didn't work with 24_LE.

Sorry, S24_LE is completely wrong; that should have been S32_LE.

Regards,
Clemens