Skip to contentSkip to conversation

One to One port range forwarding to different port range

DISCUSSION Doug Applegate 3 participants 4 messages Aug 5, 2015 – Aug 6, 2015

lore
Share & tools
lore
#0 lore raw

Hello,

After testing and looking at the kernel source, I realize that this mapping:

iptables -t nat -I PREROUTING -p tcp -m tcp --dport 30000:40000 -j DNAT --to [local_ip]:10000-2000

Doesn't do a one-to-one port mapping
e.g.:
100.0.0.1:30000 > 192.168.0.5:10000
100.0.0.1.30001 > 192.168.0.5:10001
100.0.0.1.30002 > 192.168.0.5:10002

I was wondering if it was possible to do the 1:1 port range forwarding to different port ranges or if you have to use individual rules.

Thanks

Doug

#1 lore raw

Firstly assuming that 2000 is a typo. It should be 20000.

This will probably do a one-to-one port mapping but that mapping will be dynamic, depending on which port comes first.
so it could be
100.0.0.1:30003 > 192.168.0.5 : 10000
100.0.0.1:30001 > 192.168.0.5 : 10001
100.0.0.1:33567 > 192.168.0.5 : 10002

Just depending on what order the traffic comes and what is the next free port (Probably?)!

-Akshat

Quoted 23 lines · Doug Applegate

Hello,

After testing and looking at the kernel source, I realize that this mapping:

iptables -t nat -I PREROUTING -p tcp -m tcp --dport 30000:40000 -j DNAT --to [local_ip]:10000-2000

Doesn't do a one-to-one port mapping
e.g.:
100.0.0.1:30000 > 192.168.0.5:10000
100.0.0.1.30001 > 192.168.0.5:10001
100.0.0.1.30002 > 192.168.0.5:10002

I was wondering if it was possible to do the 1:1 port range forwarding to different port ranges or if you have to use individual rules.

Thanks

Doug
--
To unsubscribe from this list: send the line "unsubscribe netfilter" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw

Akshat,

Thanks for clarifying the behaviour. I'm assuming then, that the only way to get 1:1 port mappings with different end point ports is to create a separate rule for each port?

Doug

Quoted 42 lines · Akshat Kakkar

Firstly assuming that 2000 is a typo. It should be 20000.

This will probably do a one-to-one port mapping but that mapping will be dynamic, depending on which port comes first.
so it could be
100.0.0.1:30003 > 192.168.0.5 : 10000
100.0.0.1:30001 > 192.168.0.5 : 10001
100.0.0.1:33567 > 192.168.0.5 : 10002

Just depending on what order the traffic comes and what is the next free port (Probably?)!

-Akshat

Quoted 16 lines · Doug Applegate

Hello,

After testing and looking at the kernel source, I realize that this mapping:

iptables -t nat -I PREROUTING -p tcp -m tcp --dport 30000:40000 -j DNAT --to [local_ip]:10000-2000

Doesn't do a one-to-one port mapping
e.g.:
100.0.0.1:30000 > 192.168.0.5:10000
100.0.0.1.30001 > 192.168.0.5:10001
100.0.0.1.30002 > 192.168.0.5:10002

I was wondering if it was possible to do the 1:1 port range forwarding to different port ranges or if you have to use individual rules.

Quoted 7 lines

Thanks

Doug
--
To unsubscribe from this list: send the line "unsubscribe netfilter" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

!SIG:55c30c7a225911004013073!

Signature · 1 line
Doug Applegate | Firmware Engineer | Cradlepoint
#3 lore raw

When I saw this thread yesterday, I tried to pull this off using the NETMAP target--obviously no dice. To netfilter devs: could the NETMAP target be extended to work with port numbers as well as IP addresses?

John

Signature · 7 lines
John Miller
Systems Engineer
Brandeis University
[email protected]


On Thu, Aug 6, 2015 at 11:29 AM, Doug Applegate
Quoted 46 lines · <[email protected]> wrote:

Akshat,

Thanks for clarifying the behaviour. I'm assuming then, that the only way to get 1:1 port mappings with different end point ports is to create a separate rule for each port?

Doug

Quoted 37 lines · Akshat Kakkar

Firstly assuming that 2000 is a typo. It should be 20000.

This will probably do a one-to-one port mapping but that mapping will be dynamic, depending on which port comes first.
so it could be
100.0.0.1:30003 > 192.168.0.5 : 10000
100.0.0.1:30001 > 192.168.0.5 : 10001
100.0.0.1:33567 > 192.168.0.5 : 10002

Just depending on what order the traffic comes and what is the next free port (Probably?)!

-Akshat

Quoted 19 lines · Doug Applegate

Hello,

After testing and looking at the kernel source, I realize that this mapping:

iptables -t nat -I PREROUTING -p tcp -m tcp --dport 30000:40000 -j DNAT --to
[local_ip]:10000-2000

Doesn't do a one-to-one port mapping
e.g.:
100.0.0.1:30000 > 192.168.0.5:10000
100.0.0.1.30001 > 192.168.0.5:10001
100.0.0.1.30002 > 192.168.0.5:10002

I was wondering if it was possible to do the 1:1 port range forwarding to different port ranges or if you have to use individual rules.