ZYNQ, ZC702 getting started
Hi,
i am currently starting development software for a new B&R board based on the ZYNQ7000.
To make live easier i want to try start with the Xilinx Evalboard ZC702, get there some experience to start afterwards with my own board.
I have allready built "zynq_zc702_defconfig" - but have no plan how to bring the build output to my board.
Is it necessary to build some FSBL with the Xilinx SDK an merge the output with u-boot's output ?
Or is it possible to take some SPL und U-Boot, burn it so SD-Card or QSPI flash and run ?
many thanks for help and best regards,
Hannes
Quoted 8 lines · Hannes Schmelzer
Hi,
i am currently starting development software for a new B&R board based on the ZYNQ7000.
To make live easier i want to try start with the Xilinx Evalboard ZC702, get there some experience to start afterwards with my own board.
Quoted 6 lines
I have allready built "
zynq_zc702_defconfig" - but have no plan how to bring the build output to my board.
Is it necessary to build some FSBL with the Xilinx SDK an merge the output with u-boot's output ?
Or is it possible to take some SPL und U-Boot, burn it so SD-Card or QSPI flash and run ?
Either works fine.
For SPL use mmc instead of QSPI - qspi patches on the way to merge mainline.
mmc:
build the source in mainline and download zynq boot.bin generator from
[1] and copy boot.bin and u-boot-dtb.img on to sd card, thats it.
[1] https://github.com/openedev/u-boot-zynq/blob/master/tools/zynq-boot-bin.py
Quoted 4 lines
many thanks for help and best regards,
Hannes
thanks!
Signature · 1 line
Jagan | openedev.
Quoted 16 lines
Quoted 8 lines
Hi,
i am currently starting development software for a new B&R board based on the ZYNQ7000.
To make live easier i want to try start with the Xilinx Evalboard ZC702, get there some experience to start afterwards with my own board.
Quoted 6 lines
I have allready built "
zynq_zc702_defconfig" - but have no plan how to bring the build output to my board.
Is it necessary to build some FSBL with the Xilinx SDK an merge the output with u-boot's output ?
Or is it possible to take some SPL und U-Boot, burn it so SD-Card or QSPI flash and run ?Either works fine.
Quoted 7 lines
For SPL use mmc instead of QSPI - qspi patches on the way to merge mainline.
mmc:
build the source in mainline and download zynq boot.bin generator from
[1] and copy boot.bin and u-boot-dtb.img on to sd card, thats it.[1] https://github.com/openedev/u-boot-zynq/blob/master/tools/zynq-boot-bin.py
Hi jagan,
many thanks for response and help.
It is now bit more cleaner to me ... in final i wan't to use hw guys output (ps7_* files) and build my software.
At this point i think, i don't need the Vivado or Xilinx SDK at all ... just my ARM toolchain and u-boot. Fine.
For the beginning i will use mmc (or maybe jtag). Finally i must use qspi. I think the QSPI support can be found on your github [1].
I've downloaded [1] ... and run:
~/work/u-boot-zynq $ tools/zynq-boot-bin.pytest.py -u <inputfile> -o <outputfile>
What is the input file ?
For my understanding, i need 2 input files (SPL and u-boot), or i'm wrong ?
best regards,
Hannes
Quoted 31 lines · Hannes Schmelzer
Quoted 23 lines
Quoted 9 lines
Hi,
i am currently starting development software for a new B&R board based on the ZYNQ7000.
To make live easier i want to try start with the Xilinx Evalboard ZC702, get
there some experience to start afterwards with my own board.Quoted 8 lines
I have allready built "
zynq_zc702_defconfig" - but have no plan how to bring
the build output to my board.
Is it necessary to build some FSBL with the Xilinx SDK an merge the output
with u-boot's output ?
Or is it possible to take some SPL und U-Boot, burn it so SD-Card or QSPI flash and run ?Either works fine.
For SPL use mmc instead of QSPI - qspi patches on the way to merge mainline.
Quoted 6 lines
mmc:
build the source in mainline and download zynq boot.bin generator from
[1] and copy boot.bin and u-boot-dtb.img on to sd card, thats it.[1]
https://github.com/openedev/u-boot-zynq/blob/master/tools/zynq-boot-bin.py
Quoted 8 lines
Hi jagan,
many thanks for response and help.
It is now bit more cleaner to me ... in final i wan't to use hw guys output (ps7_* files) and build my software.
At this point i think, i don't need the Vivado or Xilinx SDK at all ... just my ARM toolchain and u-boot. Fine.
Yes.
Quoted 11 lines
For the beginning i will use mmc (or maybe jtag). Finally i must use qspi. I think the QSPI support can be found on your github [1].
I've downloaded [1] ... and run:
~/work/u-boot-zynq $
tools/zynq-boot-bin.pytest.py-u <inputfile> -o <outputfile>What is the input file ?
For my understanding, i need 2 input files (SPL and u-boot), or i'm wrong ?
See this wiki [1] and just try qspi as well and let me know for any questions.
[1] http://www.openedev.com/wiki/Main_Page
thanks!
Signature · 1 line
Jagan | openedev.
Quoted 48 lines · Jagan Teki
Quoted 29 lines · Hannes Schmelzer
Quoted 22 lines
Quoted 9 lines
Hi,
i am currently starting development software for a new B&R board based on the ZYNQ7000.
To make live easier i want to try start with the Xilinx Evalboard ZC702, get
there some experience to start afterwards with my own board.Quoted 8 lines
I have allready built "
zynq_zc702_defconfig" - but have no plan how to bring
the build output to my board.
Is it necessary to build some FSBL with the Xilinx SDK an merge the output
with u-boot's output ?
Or is it possible to take some SPL und U-Boot, burn it so SD-Card or QSPI flash and run ?Either works fine.
For SPL use mmc instead of QSPI - qspi patches on the way to merge mainline.
Quoted 6 lines
mmc:
build the source in mainline and download zynq boot.bin generator from
[1] and copy boot.bin and u-boot-dtb.img on to sd card, thats it.[1]
https://github.com/openedev/u-boot-zynq/blob/master/tools/zynq-boot-bin.pyQuoted 8 lines
Hi jagan,
many thanks for response and help.
It is now bit more cleaner to me ... in final i wan't to use hw guys output (ps7_* files) and build my software.
At this point i think, i don't need the Vivado or Xilinx SDK at all ... just my ARM toolchain and u-boot. Fine.Yes.
Quoted 8 lines
For the beginning i will use mmc (or maybe jtag). Finally i must use qspi. I think the QSPI support can be found on your github [1].
I've downloaded [1] ... and run:
~/work/u-boot-zynq $
tools/zynq-boot-bin.pytest.py-u <inputfile> -o <outputfile>
Quoted 7 lines
Quoted 2 lines
What is the input file ?
For my understanding, i need 2 input files (SPL and u-boot), or i'm wrong ?See this wiki [1] and just try qspi as well and let me know for any questions.
[1] http://www.openedev.com/wiki/Main_Page
thanks!
Hi Jagan,
many thanks - with your help i got it work :-)
I tried both, mainline u-boot and which one from openedev.
I observed a little issue on both versions. If i type "reset" or press the SRST_B button i get:
U-Boot SPL 2015.07-rc3-g0cf5d8d (Sep 18 2015 - 11:22:16) mmc bootzynq_sdhci_init: sdhci_host malloc fail
MMC Device 0 not found
spl: mmc device not found
### ERROR ### Please RESET the board ###
if i simple power on or press the POR_B button it works as expected:
U-Boot SPL 2015.07-rc3-g0cf5d8d (Sep 18 2015 - 11:22:16) mmc boot
reading system.dtbspl_load_image_fat_os: error reading image system.dtb, err - -1 reading u-boot-dtb.img
reading u-boot-dtb.img
U-Boot 2015.07-rc3-g0cf5d8d (Sep 18 2015 - 11:23:17 +0200)
Model: Zynq ZC702 Board I2C: ready DRAM: ECC disabled 1 GiB MMC: zynq_sdhci: 0
Using default environment
In: serial Out: serial Err: serial Model: Zynq ZC702 Board Net: Gem.e000b000 Error: Gem.e000b000 address not set.
Hit any key to stop autoboot: 0
zynq-uboot>
best regards,
Hannes
Quoted 114 lines · Hannes Schmelzer
Quoted 65 lines · Jagan Teki
Quoted 38 lines · Hannes Schmelzer
Quoted 27 lines
Quoted 12 lines
Hi,
i am currently starting development software for a new B&R board based on
the ZYNQ7000.To make live easier i want to try start with the Xilinx Evalboard ZC702,
get
there some experience to start afterwards with my own board.Quoted 9 lines
I have allready built "
zynq_zc702_defconfig" - but have no plan how to bring
the build output to my board.
Is it necessary to build some FSBL with the Xilinx SDK an merge the output
with u-boot's output ?
Or is it possible to take some SPL und U-Boot, burn it so SD-Card or QSPI
flash and run ?Either works fine.
For SPL use mmc instead of QSPI - qspi patches on the way to merge mainline.
Quoted 7 lines
mmc:
build the source in mainline and download zynq boot.bin generator from
[1] and copy boot.bin and u-boot-dtb.img on to sd card, thats it.[1]
https://github.com/openedev/u-boot-zynq/blob/master/tools/zynq-boot-bin.py
Hi jagan,
Quoted 8 lines
many thanks for response and help.
It is now bit more cleaner to me ... in final i wan't to use hw guys output
(ps7_* files) and build my software.
At this point i think, i don't need the Vivado or Xilinx SDK at all ... just
my ARM toolchain and u-boot. Fine.Yes.
Quoted 4 lines
For the beginning i will use mmc (or maybe jtag). Finally i must use qspi. I
think the QSPI support can be found on your github [1].Quoted 8 lines
I've downloaded [1] ... and run:
~/work/u-boot-zynq $
tools/zynq-boot-bin.pytest.py-u <inputfile> -o <outputfile>What is the input file ?
For my understanding, i need 2 input files (SPL and u-boot), or i'm wrong ?Quoted 6 lines
See this wiki [1] and just try qspi as well and let me know for any questions.
[1] http://www.openedev.com/wiki/Main_Page
thanks!
Hi Jagan,
many thanks - with your help i got it work :-)
I tried both, mainline u-boot and which one from openedev.I observed a little issue on both versions. If i type "reset" or press the
SRST_Bbutton i get:U-Boot SPL 2015.07-rc3-g0cf5d8d (Sep 18 2015 - 11:22:16) mmc boot
zynq_sdhci_init:sdhci_hostmalloc fail
MMC Device 0 not found
spl: mmc device not found
### ERROR ### Please RESET the board ###if i simple power on or press the
POR_Bbutton it works as expected:U-Boot SPL 2015.07-rc3-g0cf5d8d (Sep 18 2015 - 11:22:16) mmc boot
reading system.dtbspl_load_image_fat_os: error reading image system.dtb, err - -1 reading u-boot-dtb.img
reading u-boot-dtb.imgU-Boot 2015.07-rc3-g0cf5d8d (Sep 18 2015 - 11:23:17 +0200)
Model: Zynq ZC702 Board I2C: ready DRAM: ECC disabled 1 GiB MMC: zynq_sdhci: 0Using default environment
In: serial Out: serial Err: serial Model: Zynq ZC702 Board Net: Gem.e000b000 Error: Gem.e000b000 address not set.
Quoted 2 lines
Hit any key to stop autoboot: 0
zynq-uboot>
Can you try qspi:
boot.bin - 0x0
u-boot-dtb.img - 0x100000
Signature · 1 line
Jagan | openedev.