iio: Non multiplexed ADC Data
I'm in th eprocess of writing a driver for a custom ADC controller.
It's an FPGA based ADC controller with multiple ADC channels with a built in DMA master. All channels share some attributes, eg Sample rate, with other per channel attributes, eg Gain. The DMA controller de-multiplexes the ADC data by having a separate target buffer for each channel. Look at the libiio interface this configuration doesn't seem to be catered for.
eg: iio_device_create_buffer creates a single buffer for all enabled channels to share.
The best way I can see is to create an iio device per channel and have them share a common data block. Not sure what interesting behaviour this may cause.
Or have I missed something obvious..
Signature · 2 lines
Regards Phil Reid
Quoted 3 lines · Phil Reid
I'm in th eprocess of writing a driver for a custom ADC controller. It's an FPGA based ADC controller with multiple ADC channels with a built in DMA master.
Is it a single ADC with a sequencer or multiple ADCs?
Quoted 4 lines
All channels share some attributes, eg Sample rate, with other per channel attributes, eg Gain.
The DMA controller de-multiplexes the ADC data by having a separate target buffer for each channel.
I'm curious, why?
Quoted 7 lines
Look at the libiio interface this configuration doesn't seem to be catered for.
eg:iio_device_create_buffercreates a single buffer for all enabled channels to share.The best way I can see is to create an iio device per channel and have them share a common data block.
Not sure what interesting behaviour this may cause.
Yes, you are right, this is not supported at the moment. But we'll have to add support for this at some point. In my opinion the best way to address this is to add multi-planar buffers, similar like you can for example find the in the video world[1], where different components can be in different buffers, rather than being interleaved in a single buffer.
In addition to having a scan_index a channel would have a plane_index and for each unique plane_index for the enabled channels one buffer would need to be allocated.
Since using this with the read()/write() API still requires multiplexing over a single stream its probably not the best suited API for this and I guess it will work much better with the (not yet upstream) mmap[2] support.
The workaround with multiple devices might work somewhat but I think it will be very cumbersome to use, e.g. all your buffers can be enabled/disabled independently through the API, which probably doesn't really match the hardware.
- Lars
[1] http://linuxtv.org/downloads/v4l-dvb-apis/planar-apis.html
[2]
http://events.linuxfoundation.org/sites/events/files/slides/iio_high_speed.pdf#page=18
G'day Lars,
Quoted 6 lines · Lars-Peter Clausen
Quoted 3 lines · Phil Reid
I'm in th eprocess of writing a driver for a custom ADC controller. It's an FPGA based ADC controller with multiple ADC channels with a built in DMA master.
Is it a single ADC with a sequencer or multiple ADCs?
Multiple parallel ADC's with common clock and control.
Quoted 7 lines
Quoted 5 lines
All channels share some attributes, eg Sample rate, with other per channel attributes, eg Gain.
The DMA controller de-multiplexes the ADC data by having a separate target buffer for each channel.I'm curious, why?
It's a port of an existing system and each channels data is serialised independently. There could be multiple devices collecting data with any number of channels active. It's probably best to say the source data typically isn't multiplexed. Though with some hardware it is streamed from the ADC as TDM stream and then de-multiplexed, other hardware the streams are independent..
Quoted 9 lines
Quoted 8 lines
Look at the libiio interface this configuration doesn't seem to be catered for.
eg:iio_device_create_buffercreates a single buffer for all enabled channels to share.The best way I can see is to create an iio device per channel and have them share a common data block.
Not sure what interesting behaviour this may cause.
Quoted 6 lines
Yes, you are right, this is not supported at the moment. But we'll have to add support for this at some point. In my opinion the best way to address this is to add multi-planar buffers, similar like you can for example find the in the video world[1], where different components can be in different buffers, rather than being interleaved in a single buffer.
I'll have a look to see if if that concept works for us. I was also thinking of something like this by making some hardcoded assumptions about our data.
Signature · 2 lines
Regards Phil Reid