iMX6 second boot: from SDCard
Hello everybody,
first of all, I would say a BIG thank to everybody point me out on have a USB-Serial Downloader working and Barebox up and running in my custom iMX6Q based board.
Right now I wish to know what can be done or not done to fireup the board from attached microSD card which is working because Barebox (from USB Downloader) is seeing it and find any partition scheme found on it.
If I simply write the barebox-flash-image (currently a symlink to image/barebox-[BOARD].img file) to a sdcard with command:
[my usb-adapter is seeing the sdcard as /dev/sdk]
dd if=barebox-flash-image of=/dev/sdk
it works, but actually I have lost all MBR partition scheme at all.
I read somewhere (https://community.freescale.com/docs/DOC-95015) that writing the .imx file with an offset of 1K from the beginning of the card it should run.
Actually it is not. :-(
Does barebox building this kinda of image? I see under the images folder, a file named:
start_imx6_[BOARD].pblx.imximg
but as far as I can see, this file is the same as the barebox-[BOARD]-imx6q.img...
The Reference Manual in the Boot Section does not explain well on HOW TO PREPARE a MICROSD card just to be sure the DCD and other stuff (like PBL) have to be written just to bootstrap from microSD/MMC...
Can anybody help me out on this?
Best Regards,
Signature · 9 lines
Eurek s.r.l. | Electronic Engineering | http://www.eurek.it via Celletta 8/B, 40026 Imola, Italy | Phone: +39-(0)542-609120 p.iva 00690621206 - c.f. 04020030377 | Fax: +39-(0)542-609212 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: iMX6 second boot: from SDCard [SOLVED]
Quoted 16 lines · gianluca
Hello everybody,
first of all, I would say a BIG thank to everybody point me out on have a USB-Serial Downloader working and Barebox up and running in my custom iMX6Q based board.Right now I wish to know what can be done or not done to fireup the board from attached microSD card which is working because Barebox (from USB Downloader) is seeing it and find any partition scheme found on it.
If I simply write the barebox-flash-image (currently a symlink to image/barebox-[BOARD].img file) to a sdcard with command:
[my usb-adapter is seeing the sdcard as
/dev/sdk]dd if=barebox-flash-image of=/dev/sdk
Quoted 8 lines
it works, but actually I have lost all MBR partition scheme at all.
I read somewhere (https://community.freescale.com/docs/DOC-95015) that writing the .imx file with an offset of 1K from the beginning of the card it should run.
Actually it is not. :-(
I can answer to this by myself ;-)
The issue is to write skipping the fisrt 1024 of the sdcard (bs=512 skip=2 and skipping the first 1k from the image itself [seek=2])
dd if=barebox-flash-image of=/dev/sdk bs=512 seek=2 skip=2
works fine.
Sorry for noise.
;-P
Signature · 9 lines
Eurek s.r.l. | Electronic Engineering | http://www.eurek.it via Celletta 8/B, 40026 Imola, Italy | Phone: +39-(0)542-609120 p.iva 00690621206 - c.f. 04020030377 | Fax: +39-(0)542-609212 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox