Skip to contentSkip to conversation

4.5.0 on sun7i-a20-olinuxino-lime2: libphy: PHY stmmac-0:ffffffff not found (regression from rc7)

DISCUSSION Bert Lindner 9 participants 18 messages Mar 16, 2016 – May 23, 2016 11 messages not in the archive

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

Hi,

Hopefully this is the correct place and way to report this.

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

     link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Best,

-Bert

grep -i 'mac\|eth\|sun[457]' config-4.5.0-rc7
CONFIG_MAC_PARTITION=y
# CONFIG_MACH_SUN4I is not set
# CONFIG_MACH_SUN5I is not set
# CONFIG_MACH_SUN6I is not set
CONFIG_MACH_SUN7I=y
# CONFIG_MACH_SUN8I is not set
# CONFIG_MACH_SUN9I is not set
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_IP_SET_BITMAP_IPMAC=m
CONFIG_IP_SET_HASH_MAC=m
CONFIG_SCTP_DEFAULT_COOKIE_HMAC_MD5=y
# CONFIG_SCTP_DEFAULT_COOKIE_HMAC_SHA1 is not set
# CONFIG_SCTP_DEFAULT_COOKIE_HMAC_NONE is not set
CONFIG_SCTP_COOKIE_HMAC_MD5=y
# CONFIG_SCTP_COOKIE_HMAC_SHA1 is not set
CONFIG_L2TP_ETH=m
CONFIG_MAC80211=m
CONFIG_MAC80211_HAS_RC=y
CONFIG_MAC80211_RC_MINSTREL=y
CONFIG_MAC80211_RC_MINSTREL_HT=y
CONFIG_MAC80211_RC_MINSTREL_VHT=y
CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
CONFIG_MAC80211_RC_DEFAULT="minstrel_ht"
CONFIG_MAC80211_MESH=y
CONFIG_MAC80211_LEDS=y
# CONFIG_MAC80211_DEBUGFS is not set
# CONFIG_MAC80211_MESSAGE_TRACING is not set
# CONFIG_MAC80211_DEBUG_MENU is not set
CONFIG_MAC80211_STA_HASH_MAX_SIZE=0
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MACVLAN is not set
# CONFIG_VETH is not set
CONFIG_ETHERNET=y
CONFIG_SUN4I_EMAC=m
# CONFIG_HIX5HD2_GMAC is not set
# CONFIG_HIP04_ETH is not set
# CONFIG_ETHOC is not set
CONFIG_STMMAC_ETH=y
CONFIG_STMMAC_PLATFORM=y
CONFIG_DWMAC_GENERIC=m
CONFIG_DWMAC_IPQ806X=m
CONFIG_DWMAC_LPC18XX=m
CONFIG_DWMAC_MESON=m
CONFIG_DWMAC_ROCKCHIP=m
CONFIG_DWMAC_SOCFPGA=m
CONFIG_DWMAC_STI=m
CONFIG_DWMAC_SUNXI=y
# CONFIG_SYNOPSYS_DWC_ETH_QOS is not set
CONFIG_MDIO_SUN4I=m
# CONFIG_MDIO_BCM_UNIMAC is not set
# CONFIG_USB_KAWETH is not set
CONFIG_USB_NET_CDCETHER=m
# CONFIG_USB_NET_CX82310_ETH is not set
# CONFIG_USB_IPHETH is not set
# CONFIG_BRCMSMAC is not set
# CONFIG_BRCMFMAC is not set
# CONFIG_MAC80211_HWSIM is not set
CONFIG_TOUCHSCREEN_SUN4I=m
CONFIG_SERIO_SUN4I_PS2=y
CONFIG_SPI_SUN4I=y
# CONFIG_PINCTRL_SUN4I_A10 is not set
# CONFIG_PINCTRL_SUN5I_A10S is not set
# CONFIG_PINCTRL_SUN5I_A13 is not set
CONFIG_PINCTRL_SUN7I_A20=y
# CONFIG_FB_MACMODES is not set
# CONFIG_USB_ETH is not set
CONFIG_DMA_SUN4I=y
# CONFIG_DW_DMAC is not set
CONFIG_SUN4I_TIMER=y
CONFIG_SUN5I_HSTIMER=y
CONFIG_PWM_SUN4I=m
CONFIG_PHY_SUN4I_USB=y
CONFIG_NLS_MAC_ROMAN=m
CONFIG_NLS_MAC_CELTIC=m
CONFIG_NLS_MAC_CENTEURO=m
CONFIG_NLS_MAC_CROATIAN=m
CONFIG_NLS_MAC_CYRILLIC=m
CONFIG_NLS_MAC_GAELIC=m
CONFIG_NLS_MAC_GREEK=m
CONFIG_NLS_MAC_ICELAND=m
CONFIG_NLS_MAC_INUIT=m
CONFIG_NLS_MAC_ROMANIAN=m
CONFIG_NLS_MAC_TURKISH=m
CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
CONFIG_CRYPTO_CMAC=m
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_VMAC is not set
CONFIG_CRYPTO_DRBG_HMAC=y
# CONFIG_CRYPTO_DEV_SUN4I_SS is not set

#1 lore raw
Quoted 40 lines · Bert Lindner

Hi,

Hopefully this is the correct place and way to report this.

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

     link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Quoted 3 lines

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Can you please try reverting 88f8b1b ("stmmac: Fix 'eth0: No PHY found' regression") and report whether or not this changes anything? This seems to be the only stmac patch between -rc7 and release...

Thanks,

	M.
Signature · 1 line
Jazz is not dead. It just smells funny...
#2 lore raw
Quoted 41 lines · Marc Zyngier
Quoted 40 lines · Bert Lindner

Hi,

Hopefully this is the correct place and way to report this.

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

      link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Quoted 7 lines
Quoted 3 lines

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Can you please try reverting 88f8b1b ("stmmac: Fix 'eth0: No PHY found' regression") and report whether or not this changes anything? This seems to be the only stmac patch between -rc7 and release...

Sounds like the same thing as the giant ongoing discussion thread here:

http://thread.gmane.org/gmane.linux.drivers.devicetree/159007/focus=402830

Robin.

Quoted 5 lines

Thanks,

	M.
#3 lore raw
Quoted 46 lines · Robin Murphy
Quoted 45 lines · Marc Zyngier
Quoted 43 lines · Bert Lindner

Hi,

Hopefully this is the correct place and way to report this.

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

      link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Quoted 7 lines
Quoted 3 lines

Can you please try reverting 88f8b1b ("stmmac: Fix 'eth0: No PHY found' regression") and report whether or not this changes anything? This seems to be the only stmac patch between -rc7 and release...

Sounds like the same thing as the giant ongoing discussion thread here:

http://thread.gmane.org/gmane.linux.drivers.devicetree/159007/focus=402830

Seems related indeed. What a mess.

Bert, if you can confirm that reverting this patch solves your issue, maybe it'd be worth shimming in in that thread, as it looks like a bunch of systems are affected.

Thanks,

	M.
Signature · 1 line
Jazz is not dead. It just smells funny...
#5 lore raw
In reply to a message not in the archive

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 3 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner
Quoted 1 line

Hopefully this is the correct place and way to report this.

The main discussion is on netdev list actually, CC'ed.

Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

      link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Quoted 7 lines
Quoted 3 lines

Can you please try reverting 88f8b1b ("stmmac: Fix 'eth0: No PHY found' regression") and report whether or not this changes anything? This seems to be the only stmac patch between -rc7 and release...

Sounds like the same thing as the giant ongoing discussion thread here:

http://thread.gmane.org/gmane.linux.drivers.devicetree/159007/focus=402830

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

v2 fixes for linux-next here:

https://patchwork.ozlabs.org/patch/598331/ (revert)
https://patchwork.ozlabs.org/patch/598332/

Please let Peppe know whether they work for you guys.

Cheers,
Andreas

Signature · 2 lines
SUSE Linux GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany
GF: Felix Imend?rffer, Jane Smithard, Graham Norton; HRB 21284 (AG N?rnberg)
#7 lore raw
In reply to a message not in the archive
Quoted 60 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 3 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner
Quoted 1 line

Hopefully this is the correct place and way to report this.

The main discussion is on netdev list actually, CC'ed.

Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Quoted 7 lines
Quoted 3 lines

Can you please try reverting 88f8b1b ("stmmac: Fix 'eth0: No PHY found' regression") and report whether or not this changes anything? This seems to be the only stmac patch between -rc7 and release...

Sounds like the same thing as the giant ongoing discussion thread here:

http://thread.gmane.org/gmane.linux.drivers.devicetree/159007/focus=402830

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

Quoted 6 lines

v2 fixes for linux-next here:

https://patchwork.ozlabs.org/patch/598331/ (revert)
https://patchwork.ozlabs.org/patch/598332/

Please let Peppe know whether they work for you guys.

Hi guys - I can confirm 4.5.0 minus 88f8b1b works for me:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-minus-88f8b1b (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #2 SMP Wed Mar 16 12:50:03 UTC 2016

From dmesg output:

[    9.731730] NET: Registered protocol family 10
[   10.516893]  RX IPC Checksum Offload disabled
[   10.516948]  No MAC Management Counters available
[   10.517374] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.505548] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 
1Gbps/Full - flow control off
[   15.505660] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

.. and connected over ethernet.

Thanks, best,

-bert

#9 lore raw
In reply to a message not in the archive
Quoted 83 lines · Bert Lindner
Quoted 60 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 3 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner
Quoted 1 line

Hopefully this is the correct place and way to report this.

The main discussion is on netdev list actually, CC'ed.

Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Quoted 7 lines
Quoted 3 lines

Can you please try reverting 88f8b1b ("stmmac: Fix 'eth0: No PHY found' regression") and report whether or not this changes anything? This seems to be the only stmac patch between -rc7 and release...

Sounds like the same thing as the giant ongoing discussion thread here:

http://thread.gmane.org/gmane.linux.drivers.devicetree/159007/focus=402830

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

Quoted 6 lines

v2 fixes for linux-next here:

https://patchwork.ozlabs.org/patch/598331/ (revert)
https://patchwork.ozlabs.org/patch/598332/

Please let Peppe know whether they work for you guys.

Hi guys - I can confirm 4.5.0 minus 88f8b1b works for me:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-minus-88f8b1b (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #2 SMP Wed Mar 16 12:50:03 UTC 2016

From dmesg output:

[    9.731730] NET: Registered protocol family 10
[   10.516893]  RX IPC Checksum Offload disabled
[   10.516948]  No MAC Management Counters available
[   10.517374] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.505548] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 
1Gbps/Full - flow control off
[   15.505660] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 1 line

.. and connected over ethernet.

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next will actually fix the issue.

Thanks,

	M.
Signature · 1 line
Jazz is not dead. It just smells funny...
#11 lore raw
In reply to a message not in the archive
Quoted 84 lines · Marc Zyngier
Quoted 83 lines · Bert Lindner
Quoted 60 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 3 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner
Quoted 1 line

Hopefully this is the correct place and way to report this.

The main discussion is on netdev list actually, CC'ed.

Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Quoted 7 lines
Quoted 3 lines

Can you please try reverting 88f8b1b ("stmmac: Fix 'eth0: No PHY found' regression") and report whether or not this changes anything? This seems to be the only stmac patch between -rc7 and release...

Sounds like the same thing as the giant ongoing discussion thread here:

http://thread.gmane.org/gmane.linux.drivers.devicetree/159007/focus=402830

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

Quoted 6 lines

v2 fixes for linux-next here:

https://patchwork.ozlabs.org/patch/598331/ (revert)
https://patchwork.ozlabs.org/patch/598332/

Please let Peppe know whether they work for you guys.

Hi guys - I can confirm 4.5.0 minus 88f8b1b works for me:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-minus-88f8b1b (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #2 SMP Wed Mar 16 12:50:03 UTC 2016

From dmesg output:

[    9.731730] NET: Registered protocol family 10
[   10.516893]  RX IPC Checksum Offload disabled
[   10.516948]  No MAC Management Counters available
[   10.517374] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.505548] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.505660] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 5 lines
Quoted 1 line

.. and connected over ethernet.

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

I'm less familiar with linux-next - not sure what base to test against, I understand it is being redefined almost daily.

Thanks!

-Bert

#13 lore raw
In reply to a message not in the archive
Quoted 107 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 84 lines · Marc Zyngier
Quoted 83 lines · Bert Lindner
Quoted 60 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 3 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner
Quoted 1 line

Hopefully this is the correct place and way to report this.

The main discussion is on netdev list actually, CC'ed.

Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

root at lime2-079f:~# ip a l eth0
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 02:c9:05:02:07:9f brd ff:ff:ff:ff:ff:ff

Difference reported in dmesg:

4.5.0-rc7:

[    9.379279] NET: Registered protocol family 10
[   10.217148]  RX IPC Checksum Offload disabled
[   10.217195]  No MAC Management Counters available
[   10.217627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.206250] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.206360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

4.5.0:

[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

.config is identical for both, also after make oldconfig, apart from comment with version number. DTB file is also identical between the two versions.

Kernels are compiled on the board itself. /proc/version string:
Linux version 4.5.0-rc7 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Mon Mar 7 11:57:25 UTC 2016 Linux version 4.5.0 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Tue Mar 15 11:39:01 UTC 2016

Please let me know if more info is needed, if I should post complete .config, test compile with a particular config or patch, etc. Part of .config below.

Quoted 7 lines
Quoted 3 lines

Can you please try reverting 88f8b1b ("stmmac: Fix 'eth0: No PHY found' regression") and report whether or not this changes anything? This seems to be the only stmac patch between -rc7 and release...

Sounds like the same thing as the giant ongoing discussion thread here:

http://thread.gmane.org/gmane.linux.drivers.devicetree/159007/focus=402830

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

Quoted 6 lines

v2 fixes for linux-next here:

https://patchwork.ozlabs.org/patch/598331/ (revert)
https://patchwork.ozlabs.org/patch/598332/

Please let Peppe know whether they work for you guys.

Hi guys - I can confirm 4.5.0 minus 88f8b1b works for me:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-minus-88f8b1b (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #2 SMP Wed Mar 16 12:50:03 UTC 2016

From dmesg output:

[    9.731730] NET: Registered protocol family 10
[   10.516893]  RX IPC Checksum Offload disabled
[   10.516948]  No MAC Management Counters available
[   10.517374] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.505548] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control off
[   15.505660] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 5 lines
Quoted 1 line

.. and connected over ethernet.

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 3 lines

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Cool, many thanks for taking the time to test and report.

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

Quoted 2 lines

I'm less familiar with linux-next - not sure what base to test against, I understand it is being redefined almost daily.

You can consider -next as a daily view of what mainline could become. An over-sized crystal ball, in a way... ;-) Given that the regression exists in mainline, there was no real point testing with -next.

Thanks again,

	M.
Signature · 1 line
Jazz is not dead. It just smells funny.
#14 lore raw

Giuseppe, Alexandre, et al.,

Quoted 8 lines · Marc Zyngier
Quoted 6 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 5 lines · Marc Zyngier
Quoted 4 lines · Bert Lindner
Quoted 3 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 2 lines · Marc Zyngier
Quoted 1 line · Bert Lindner

...

Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 24 lines
Quoted 20 lines
Quoted 3 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 3 lines

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Quoted 5 lines

Cool, many thanks for taking the time to test and report.

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(
The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

Thanks!
Andre

[0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=823493

#16 lore raw
In reply to a message not in the archive
Quoted 50 lines · Andre Heider

Giuseppe, Alexandre, et al.,

Quoted 8 lines · Marc Zyngier
Quoted 6 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 5 lines · Marc Zyngier
Quoted 4 lines · Bert Lindner
Quoted 3 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 2 lines · Marc Zyngier
Quoted 1 line · Bert Lindner

...

Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 24 lines
Quoted 23 lines
Quoted 3 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Quoted 8 lines
Quoted 5 lines

Cool, many thanks for taking the time to test and report.

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(

All the A20 platforms are dead, actually.

Quoted 2 lines

The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

For that, the maintainer would have needed to CC stable, which he didn't. I'd expect someone who cares to send these patches to stable. It'd be better if the maintainer would do it himself though.

Thanks,

	M.
Signature · 1 line
Jazz is not dead. It just smells funny...
#18 lore raw
In reply to a message not in the archive

Hello

Quoted 60 lines · Marc Zyngier
Quoted 50 lines · Andre Heider

Giuseppe, Alexandre, et al.,

Quoted 8 lines · Marc Zyngier
Quoted 6 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 5 lines · Marc Zyngier
Quoted 4 lines · Bert Lindner
Quoted 3 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 2 lines · Marc Zyngier
Quoted 1 line · Bert Lindner

...

Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 24 lines
Quoted 23 lines
Quoted 3 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Quoted 8 lines
Quoted 5 lines

Cool, many thanks for taking the time to test and report.

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(

Quoted 8 lines

All the A20 platforms are dead, actually.

Quoted 2 lines

The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

For that, the maintainer would have needed to CC stable, which he didn't. I'd expect someone who cares to send these patches to stable. It'd be better if the maintainer would do it himself though.

sure, I can send the patches to stable (sorry if I missed to add stable ML on CC).

Andre, I have not clear if the train of patches actually fix the issue or if you need my support to fix something else. In that case I need some input for debugging (e.g. kernel log).

let me know, is it enough to re-send the patches only?

Regards
Peppe

Quoted 5 lines

Thanks,

	M.
#20 lore raw
In reply to a message not in the archive

Hi,

Quoted 97 lines · Giuseppe CAVALLARO
Quoted 87 lines · Marc Zyngier
Quoted 74 lines · Andre Heider

Giuseppe, Alexandre, et al.,

Quoted 15 lines · Marc Zyngier
Quoted 12 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 10 lines · Marc Zyngier
Quoted 8 lines · Bert Lindner
Quoted 6 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 4 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem
with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 31 lines
Quoted 24 lines
Quoted 5 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next
will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 3 lines

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Cool, many thanks for taking the time to test and report.

Quoted 7 lines
Quoted 3 lines

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(

All the A20 platforms are dead, actually.

Quoted 7 lines
Quoted 2 lines

The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

For that, the maintainer would have needed to CC stable, which he didn't. I'd expect someone who cares to send these patches to stable. It'd be better if the maintainer would do it himself though.

Quoted 6 lines

sure, I can send the patches to stable (sorry if I missed to add stable ML on CC).

Andre, I have not clear if the train of patches actually fix the issue or if you need my support to fix something else. In that case I need some input for debugging (e.g. kernel log).

Bert already confirmed that those two patches fixes stmmac on his Lime2, so I assume that it fixes the issue for all A20 platforms.

Quoted 1 line

let me know, is it enough to re-send the patches only?

Just a resend with cc:stable :)

Thanks!
Andre

#21 lore raw
Quoted 108 lines · Andre Heider

Hi,

Quoted 97 lines · Giuseppe CAVALLARO
Quoted 87 lines · Marc Zyngier
Quoted 74 lines · Andre Heider

Giuseppe, Alexandre, et al.,

Quoted 15 lines · Marc Zyngier
Quoted 12 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 10 lines · Marc Zyngier
Quoted 8 lines · Bert Lindner
Quoted 6 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 4 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a problem
with the eth0 PHY in mainline kernel 4.5.0 that developed since 4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
[    9.767125] NET: Registered protocol family 10
[   10.357405] libphy: PHY stmmac-0:ffffffff not found
[   10.362382] eth0: Could not attach to PHY
[   10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 31 lines
Quoted 24 lines
Quoted 5 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next
will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 3 lines

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Cool, many thanks for taking the time to test and report.

Quoted 7 lines
Quoted 3 lines

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(

All the A20 platforms are dead, actually.

Quoted 7 lines
Quoted 2 lines

The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

For that, the maintainer would have needed to CC stable, which he didn't. I'd expect someone who cares to send these patches to stable. It'd be better if the maintainer would do it himself though.

Quoted 6 lines

sure, I can send the patches to stable (sorry if I missed to add stable ML on CC).

Andre, I have not clear if the train of patches actually fix the issue or if you need my support to fix something else. In that case I need some input for debugging (e.g. kernel log).

Quoted 6 lines

Bert already confirmed that those two patches fixes stmmac on his Lime2, so I assume that it fixes the issue for all A20 platforms.

Quoted 1 line

let me know, is it enough to re-send the patches only?

Just a resend with cc:stable :)

Not quite. Please read Documentation/stable_kernel_rules.txt, and the section that concerns networking patches (and then consult Documentation/networking/netdev-FAQ.txt which has all the details).

Thanks,

	M.
Signature · 1 line
Jazz is not dead. It just smells funny...
#23 lore raw
In reply to a message not in the archive

Hi,

Quoted 112 lines · Marc Zyngier
Quoted 111 lines · Andre Heider

Hi,

Quoted 97 lines · Giuseppe CAVALLARO
Quoted 87 lines · Marc Zyngier
Quoted 74 lines · Andre Heider

Giuseppe, Alexandre, et al.,

Quoted 15 lines · Marc Zyngier
Quoted 12 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 10 lines · Marc Zyngier
Quoted 8 lines · Bert Lindner
Quoted 6 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 4 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a
problem
with the eth0 PHY in mainline kernel 4.5.0 that developed since
4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

[ 9.767125] NET: Registered protocol family 10
[ 10.357405] libphy: PHY stmmac-0:ffffffff not found
[ 10.362382] eth0: Could not attach to PHY
[ 10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 31 lines
Quoted 24 lines
Quoted 5 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next
will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 3 lines

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Cool, many thanks for taking the time to test and report.

Quoted 7 lines
Quoted 3 lines

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(

All the A20 platforms are dead, actually.

Quoted 7 lines
Quoted 2 lines

The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

For that, the maintainer would have needed to CC stable, which he didn't. I'd expect someone who cares to send these patches to stable. It'd be better if the maintainer would do it himself though.

Quoted 6 lines

sure, I can send the patches to stable (sorry if I missed to add stable ML on CC).

Andre, I have not clear if the train of patches actually fix the issue or if you need my support to fix something else. In that case I need some input for debugging (e.g. kernel log).

Bert already confirmed that those two patches fixes stmmac on his Lime2, so I assume that it fixes the issue for all A20 platforms.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

let me know, is it enough to re-send the patches only?

Just a resend with cc:stable :)

Not quite. Please read Documentation/stable_kernel_rules.txt, and the section that concerns networking patches (and then consult Documentation/networking/netdev-FAQ.txt which has all the details).

Right, it's just been a while since I sent a patch.
What I really meant was "do what's neccessary for -stable inclusion" :)

Regards,
Andre

#24 lore raw
In reply to a message not in the archive

Hi,

Quoted 112 lines · Marc Zyngier
Quoted 111 lines · Andre Heider

Hi,

Quoted 97 lines · Giuseppe CAVALLARO
Quoted 87 lines · Marc Zyngier
Quoted 74 lines · Andre Heider

Giuseppe, Alexandre, et al.,

Quoted 15 lines · Marc Zyngier
Quoted 12 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 10 lines · Marc Zyngier
Quoted 8 lines · Bert Lindner
Quoted 6 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 4 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a
problem
with the eth0 PHY in mainline kernel 4.5.0 that developed since
4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

[ 9.767125] NET: Registered protocol family 10
[ 10.357405] libphy: PHY stmmac-0:ffffffff not found
[ 10.362382] eth0: Could not attach to PHY
[ 10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 31 lines
Quoted 24 lines
Quoted 5 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next
will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 3 lines

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Cool, many thanks for taking the time to test and report.

Quoted 7 lines
Quoted 3 lines

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(

All the A20 platforms are dead, actually.

Quoted 7 lines
Quoted 2 lines

The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

For that, the maintainer would have needed to CC stable, which he didn't. I'd expect someone who cares to send these patches to stable. It'd be better if the maintainer would do it himself though.

Quoted 6 lines

sure, I can send the patches to stable (sorry if I missed to add stable ML on CC).

Andre, I have not clear if the train of patches actually fix the issue or if you need my support to fix something else. In that case I need some input for debugging (e.g. kernel log).

Bert already confirmed that those two patches fixes stmmac on his Lime2, so I assume that it fixes the issue for all A20 platforms.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

let me know, is it enough to re-send the patches only?

Just a resend with cc:stable :)

Not quite. Please read Documentation/stable_kernel_rules.txt, and the section that concerns networking patches (and then consult Documentation/networking/netdev-FAQ.txt which has all the details).

FWIW, recent 4.6-rc series and 4.6.0 have worked fine for me and the lime2. Had not tried 4.5.x again.

Best,

-bert

#26 lore raw
In reply to a message not in the archive
Quoted 117 lines · On Sat, 21 May 2016 17:47:05 +0200 Bert Lindner <[email protected]> wrote:

Hi,

Quoted 114 lines · Marc Zyngier
Quoted 113 lines · Andre Heider

Hi,

Quoted 97 lines · Giuseppe CAVALLARO
Quoted 87 lines · Marc Zyngier
Quoted 74 lines · Andre Heider

Giuseppe, Alexandre, et al.,

Quoted 15 lines · Marc Zyngier
Quoted 12 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 10 lines · Marc Zyngier
Quoted 8 lines · Bert Lindner
Quoted 6 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 4 lines · Marc Zyngier
Quoted 2 lines · Bert Lindner

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a
problem
with the eth0 PHY in mainline kernel 4.5.0 that developed since
4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

[ 9.767125] NET: Registered protocol family 10
[ 10.357405] libphy: PHY stmmac-0:ffffffff not found
[ 10.362382] eth0: Could not attach to PHY
[ 10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 31 lines
Quoted 24 lines
Quoted 5 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next
will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 3 lines

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Cool, many thanks for taking the time to test and report.

Quoted 7 lines
Quoted 3 lines

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(

All the A20 platforms are dead, actually.

Quoted 7 lines
Quoted 2 lines

The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

For that, the maintainer would have needed to CC stable, which he didn't. I'd expect someone who cares to send these patches to stable. It'd be better if the maintainer would do it himself though.

Quoted 6 lines

sure, I can send the patches to stable (sorry if I missed to add stable ML on CC).

Andre, I have not clear if the train of patches actually fix the issue or if you need my support to fix something else. In that case I need some input for debugging (e.g. kernel log).

Bert already confirmed that those two patches fixes stmmac on his Lime2, so I assume that it fixes the issue for all A20 platforms.

Quoted 1 line

let me know, is it enough to re-send the patches only?

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

Just a resend with cc:stable :)

Not quite. Please read Documentation/stable_kernel_rules.txt, and the section that concerns networking patches (and then consult Documentation/networking/netdev-FAQ.txt which has all the details).

FWIW, recent 4.6-rc series and 4.6.0 have worked fine for me and the lime2. Had not tried 4.5.x again.

We've already established this. This is a 4.5-specific regression (both 4.4 and 4.6 are fine). One major issue is that Debian Stretch is currently shipping with 4.5, and upgrading to it results in a system without networking. Should this patch make it into stable, the fix would quickly percolate into distro kernels, and we could forget about it.

Thanks,

	M.
Signature · 1 line
Jazz is not dead. It just smells funny.
#28 lore raw
In reply to a message not in the archive

Hello

Quoted 126 lines · Marc Zyngier
Quoted 123 lines · On Sat, 21 May 2016 17:47:05 +0200 Bert Lindner <[email protected]> wrote:

Hi,

Quoted 119 lines · Marc Zyngier
Quoted 108 lines · Andre Heider

Hi,

Quoted 97 lines · Giuseppe CAVALLARO
Quoted 87 lines · Marc Zyngier
Quoted 74 lines · Andre Heider

Giuseppe, Alexandre, et al.,

Quoted 15 lines · Marc Zyngier
Quoted 12 lines · On Thu, 17 Mar 2016 00:56:40 +0100 Bert Lindner <[email protected]> wrote:
Quoted 10 lines · Marc Zyngier
Quoted 8 lines · Bert Lindner
Quoted 6 lines · Andreas F?rber

Am 16.03.2016 um 13:09 schrieb Robin Murphy:

Quoted 4 lines · Marc Zyngier

On 16/03/16 11:19, Bert Lindner wrote:

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

For the board sun7i-a20-olinuxino-lime2, there seems to be a
problem
with the eth0 PHY in mainline kernel 4.5.0 that developed since
4.5.0-rc7. Ethernet does not work, although eth0 is reported:

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

[ 9.767125] NET: Registered protocol family 10
[ 10.357405] libphy: PHY stmmac-0:ffffffff not found
[ 10.362382] eth0: Could not attach to PHY
[ 10.366557] stmmac_open: Cannot attach to PHY (error: -19)

...

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

v4 fixes for 4.5 are here:

https://patchwork.ozlabs.org/patch/598195/ (revert)
https://patchwork.ozlabs.org/patch/598196/

...

Quoted 31 lines
Quoted 24 lines
Quoted 5 lines

Good to know, thanks. Could you also give the potential fix a go (as mentioned by Andreas)? Just to make sure that whatever gets merged next
will actually fix the issue.

Yes sure, it took a while because I had to travel. Confirmed, the v4-for-4.5 fix works well for me, on sun7i-a20-olinuxino-lime2:

root at lime2-079f:~# cat /proc/version
Linux version 4.5.0-598195-598196-v4 (root at lime2-079f) (gcc version 4.9.1 (Ubuntu/Linaro 4.9.1-16ubuntu6) ) #1 SMP Wed Mar 16 16:44:22 UTC 2016

dmesg:

[    8.245273] NET: Registered protocol family 10
[    9.297406]  RX IPC Checksum Offload disabled
[    9.297460]  No MAC Management Counters available
[    9.297951] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.285658] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[   16.285798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Quoted 3 lines

The board is connected to my laptop rather than to a switch, so that might be where the flow control message comes from (not sure). Anyway ethernet works.

Cool, many thanks for taking the time to test and report.

Quoted 7 lines
Quoted 3 lines

Hopefully Giuseppe will get this merged quickly enough in mainline, and it should then trickle into a 4.5-stable release (cc-ing stable on these patches would probably be a good idea, BTW).

stmmac is broken on at least Lime2, BananaPi and Cubieboard2 since v4.5 [0], including all five stable releases :(

All the A20 platforms are dead, actually.

Quoted 7 lines
Quoted 2 lines

The v4.5 patches quoted above are already +4 weeks old, could we please get them into stable?

For that, the maintainer would have needed to CC stable, which he didn't. I'd expect someone who cares to send these patches to stable. It'd be better if the maintainer would do it himself though.

Quoted 6 lines

sure, I can send the patches to stable (sorry if I missed to add stable ML on CC).

Andre, I have not clear if the train of patches actually fix the issue or if you need my support to fix something else. In that case I need some input for debugging (e.g. kernel log).

Quoted 6 lines

Bert already confirmed that those two patches fixes stmmac on his Lime2, so I assume that it fixes the issue for all A20 platforms.

Quoted 1 line

let me know, is it enough to re-send the patches only?

Just a resend with cc:stable :)

Not quite. Please read Documentation/stable_kernel_rules.txt, and the section that concerns networking patches (and then consult Documentation/networking/netdev-FAQ.txt which has all the details).

Quoted 8 lines
Quoted 2 lines

FWIW, recent 4.6-rc series and 4.6.0 have worked fine for me and the lime2. Had not tried 4.5.x again.

We've already established this. This is a 4.5-specific regression (both 4.4 and 4.6 are fine). One major issue is that Debian Stretch is currently shipping with 4.5, and upgrading to it results in a system without networking. Should this patch make it into stable, the fix would quickly percolate into distro kernels, and we could forget about it.

I have just ported and sent the patches to stable list.

[PATCH 0/2 (linux-stable-4.5.y)] net: stmmac: MDIO fixes

Please, let me know if it is ok for you.

Peppe

Quoted 4 lines

Thanks,

	M.