bcmserver.c usage and preconditions
Hi,
I'd like to ask what preconditions are necessary for the bcmserver.c example to work.
1. I setup can0
~$ sudo ip link set can0 up type can bitrate 500000
2. then start bcmserver
~$ bcmserver
3. and input the line
~$ can0 A 1 0 123 8 11 22 33 44 55 66 77 88
but unfortunately I don't get any output at all.
I believe it's my fault since this is the result on both BananaPi and BeagleBoneBlack. The Bpi has the bcm compiled into the kernel and the BBB has the can-bcm.ko properly loaded.
~$ modinfo can-bcm
filename: /lib/modules/4.1.15-ti-rt-r43/kernel/net/can/can-bcm.ko alias: can-proto-2 author: Oliver Hartkopp <[email protected]> license: Dual BSD/GPL description: PF_CAN broadcast manager protocol depends: can intree: Y vermagic: 4.1.15-ti-rt-r43 SMP preempt mod_unload modversions
ARMv7 thumb2 p2v8
Thanks and Best Regards,
Patrick
Hi Patrick,
Have you tested CAN line without bcmserver. I mean is the CAN bus functional, are you able to transmit receive frames.
You can test it with canutils.
<http://elinux.org/Can-utils>
Best regards
Pankaj Kumar Misra
RBEI/EEA2
Tel. +49(711)8113659089 | Mobile +4915145771414
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Patrick Menschel
Sent: Wednesday, March 30, 2016 8:01 AM
To: linux-can <[email protected]>
Subject: bcmserver.c usage and preconditions
Hi,
I'd like to ask what preconditions are necessary for the bcmserver.c example to work.
1. I setup can0
~$ sudo ip link set can0 up type can bitrate 500000
2. then start bcmserver
~$ bcmserver
3. and input the line
~$ can0 A 1 0 123 8 11 22 33 44 55 66 77 88
but unfortunately I don't get any output at all.
I believe it's my fault since this is the result on both BananaPi and BeagleBoneBlack. The Bpi has the bcm compiled into the kernel and the BBB has the can-bcm.ko properly loaded.
~$ modinfo can-bcm
filename: /lib/modules/4.1.15-ti-rt-r43/kernel/net/can/can-bcm.ko alias: can-proto-2 author: Oliver Hartkopp <[email protected]> license: Dual BSD/GPL description: PF_CAN broadcast manager protocol depends: can intree: Y vermagic: 4.1.15-ti-rt-r43 SMP preempt mod_unload modversions
ARMv7 thumb2 p2v8
Thanks and Best Regards,
Patrick
Hi Pankaj,
CAN Bus is functional in both directions, rx and tx .
1. cansend works properly
2. candump also works properly
I'm just trying to verify if it's just me or the bcm.
I expect a usage error because I run a non-modified debian 8 image on the BeagleBoneBlack, which shows exactly the same behaviour.
Thanks and Best Regards,
Patrick
Am 30.03.2016 um 09:57 schrieb Misra Pankaj Kumar (RBEI/EEA2):
Quoted 61 lines
Hi Patrick,
Have you tested CAN line without bcmserver. I mean is the CAN bus functional, are you able to transmit receive frames.
You can test it with canutils.
<http://elinux.org/Can-utils>Best regards
Pankaj Kumar Misra
RBEI/EEA2Tel. +49(711)8113659089 | Mobile +4915145771414
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Patrick Menschel
Sent: Wednesday, March 30, 2016 8:01 AM
To: linux-can <[email protected]>
Subject:bcmserver.cusage and preconditionsHi,
I'd like to ask what preconditions are necessary for the
bcmserver.cexample to work.1. I setup can0
~$ sudo ip link set can0 up type can bitrate 500000
2. then start bcmserver
~$ bcmserver
3. and input the line
~$ can0 A 1 0 123 8 11 22 33 44 55 66 77 88
but unfortunately I don't get any output at all.
I believe it's my fault since this is the result on both BananaPi and BeagleBoneBlack. The Bpi has the bcm compiled into the kernel and the BBB has the can-bcm.ko properly loaded.
~$ modinfo can-bcm
filename: /lib/modules/4.1.15-ti-rt-r43/kernel/net/can/can-bcm.ko alias: can-proto-2 author: Oliver Hartkopp <[email protected]> license: Dual BSD/GPL description: PF_CAN broadcast manager protocol depends: can intree: Y vermagic: 4.1.15-ti-rt-r43 SMP preempt mod_unload modversionsARMv7 thumb2 p2v8
Thanks and Best Regards,
PatrickN�����r��y���b�X��ǧv�^�){.n�+����{�q���^n�r���z���h����&���G���h�(�階�ݢj"���m�����z�ޖ���f���h���~�mml==
Hi Patrick,
Quoted 8 lines · Patrick Menschel
Hi Pankaj,
CAN Bus is functional in both directions, rx and tx .
1. cansend works properly
2. candump also works properlyI'm just trying to verify if it's just me or the bcm.
It's you :-)
Quoted 10 lines
Quoted 10 lines
2. then start bcmserver
~$ bcmserver
3. and input the line
~$ can0 A 1 0 123 8 11 22 33 44 55 66 77 88
but unfortunately I don't get any output at all.
The bcmserver creates an IP server listening on port 28600 on localhost.
So you would need to connect this server e.g. with netcat first and then type the according command (with '<' and '>' tags!!) into the netcat shell.
Regards,
Oliver
Thanks Oliver,
based on the usage examples in the file header I thought it reads from stdin ;-P
I have it working now on both BananaPi and BeagleBoneBlack.
Regards,
Patrick
Am 30.03.2016 um 13:59 schrieb Oliver Hartkopp:
Quoted 32 lines
Hi Patrick,
Quoted 8 lines · Patrick Menschel
Hi Pankaj,
CAN Bus is functional in both directions, rx and tx .
1. cansend works properly
2. candump also works properlyI'm just trying to verify if it's just me or the bcm.
It's you :-)
Quoted 10 lines
Quoted 10 lines
2. then start bcmserver
~$ bcmserver
3. and input the line
~$ can0 A 1 0 123 8 11 22 33 44 55 66 77 88
but unfortunately I don't get any output at all.
The bcmserver creates an IP server listening on port 28600 on localhost.
So you would need to connect this server e.g. with netcat first and then type the according command (with '<' and '>' tags!!) into the netcat shell.
Regards,
Oliver