Skip to contentSkip to conversation

GPIO control from ALSA

DISCUSSION Petr Kulhavy 2 participants 6 messages Apr 20, 2016

lore
Share & tools
lore
#0 lore raw

Hello,

I'm writing a driver for ASoC "sound card" hardware which uses CPU GPIO to mute/unmute an analogue amplifier and another GPIO to control an analogue switch for line/mic switching. Is there an abstraction in ALSA to model this kind of hardware?

Thanks
Petr

#1 lore raw
Quoted 6 lines · Petr Kulhavy

Hello,

I'm writing a driver for ASoC "sound card" hardware which uses CPU GPIO to mute/unmute an analogue amplifier and another GPIO to control an analogue switch for line/mic switching. Is there an abstraction in ALSA to model this kind of hardware?

There is no abstraction. Use controls and/or DAPM and the standard GPIO API, if you grep the sources you'll find a few examples of drivers using GPIOs to mute amplifiers and similar (e.g. qi_lb60).

- Lars

#2 lore raw
Quoted 7 lines · Lars-Peter Clausen
Quoted 6 lines · Petr Kulhavy

Hello,

I'm writing a driver for ASoC "sound card" hardware which uses CPU GPIO to mute/unmute an analogue amplifier and another GPIO to control an analogue switch for line/mic switching. Is there an abstraction in ALSA to model this kind of hardware?

Quoted 5 lines

There is no abstraction. Use controls and/or DAPM and the standard GPIO API, if you grep the sources you'll find a few examples of drivers using GPIOs to mute amplifiers and similar (e.g. qi_lb60).

- Lars

Thanks, Lars, for the good pointers! I will check that out.

Is there also a way to map GPIO to a control which then appears e.g. in alsamixer? That would be useful for the mic/line selection.

Regards
Petr

#3 lore raw
Quoted 12 lines · Petr Kulhavy
Quoted 11 lines · Lars-Peter Clausen
Quoted 6 lines · Petr Kulhavy

Hello,

I'm writing a driver for ASoC "sound card" hardware which uses CPU GPIO to mute/unmute an analogue amplifier and another GPIO to control an analogue switch for line/mic switching. Is there an abstraction in ALSA to model this kind of hardware?

There is no abstraction. Use controls and/or DAPM and the standard GPIO API, if you grep the sources you'll find a few examples of drivers using GPIOs to mute amplifiers and similar (e.g. qi_lb60).

Quoted 6 lines
Quoted 1 line

- Lars

Thanks, Lars, for the good pointers! I will check that out.

Is there also a way to map GPIO to a control which then appears e.g. in alsamixer? That would be useful for the mic/line selection.

Rather than exposing the GPIO itself you'd expose the logical function of the GPIO. E.g. in your case a ENUM control that allows to switch between microphone and capture and in the background this sets the GPIO according to the selection.

- Lars

#4 lore raw
Quoted 10 lines · Lars-Peter Clausen
Quoted 5 lines · Petr Kulhavy

Thanks, Lars, for the good pointers! I will check that out.

Is there also a way to map GPIO to a control which then appears e.g. in alsamixer? That would be useful for the mic/line selection.

Rather than exposing the GPIO itself you'd expose the logical function of the GPIO. E.g. in your case a ENUM control that allows to switch between microphone and capture and in the background this sets the GPIO according to the selection.

I understand that, my question was more how to hook the enum to a function rather to a codec register?

Thanks
Petr

#5 lore raw
Quoted 9 lines · Petr Kulhavy
Quoted 6 lines · Lars-Peter Clausen
Quoted 5 lines · Petr Kulhavy

Thanks, Lars, for the good pointers! I will check that out.

Is there also a way to map GPIO to a control which then appears e.g. in alsamixer? That would be useful for the mic/line selection.

Quoted 7 lines
Quoted 4 lines

Rather than exposing the GPIO itself you'd expose the logical function of the GPIO. E.g. in your case a ENUM control that allows to switch between microphone and capture and in the background this sets the GPIO according to the selection.

I understand that, my question was more how to hook the enum to a function rather to a codec register?

You can use SOC_ENUM_EXT() to create the control. This macro takes a get and a put callback where you can manipulate the state of the GPIO. And then just register the control with the card.