Skip to contentSkip to conversation

U-boot UBI environment

U-Boot Joseph Hershberger 3 participants 4 messages May 10, 2016 – May 12, 2016 2 messages not in the archive

lore
Share & tools
lore

Joseph Hershberger

author
#2 lore raw
In reply to a message not in the archive

Hi Kevin,

Am 09.05.2016 um 23:16 schrieb Kevin Smith:

Quoted 39 lines

Hello,

I would appreciate some UBI help/advice if you are able to provide it. I am trying to use UBI to store my u-boot environment, but when I try to 'saveenv', it is corrupting another volume of my UBI. I can image the rootfs volume and boot Linux from it without a problem. However, the first time that I save the u-boot environment, the rootfs becomes unreadable. When the rootfs is corrupted, I have booted Linux from another source and tried to attach UBI and dd out the data. It appears as all 0xFF. Both u-boot and Linux can read the env volume correctly.

I do not think that there is a board in U-boot that uses UBI env, so I do not have anything to compare to. I have included some details of my setup below. Do you have any suggestion about what might be wrong? I saw the recent patch b1d6590d35, and thought it might fix it, but am still having the problem even with this. Maybe there is another bug? I am glad to provide more info as needed.
Thank you,
Kevin

DTS:

flash at d0000 {
      num-cs = <1>;
      marvell,nand-keep-config;
      marvell,nand-enable-arbiter;
      nand-on-flash-bbt;
      nand-ecc-strength = <4>;
      nand-ecc-step-size = <512>;
      status = "okay";

      partition at 0 {
          label = "mvboot";
          reg = <0 0x200000>;
      };
      partition at 200000 {
          label = "ubi";
          reg = <0x200000 0x1fe00000>;
      };
};
Quoted 8 lines

Config:
#define MTDIDS_DEFAULT "nand0=pxa3xx_nand-0"
#define MTDPARTS_DEFAULT "mtdparts=pxa3xx_nand-0:2m(mvboot),-(ubi)" #define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS

#define CONFIG_MTD_UBI_FASTMAP
#define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT 1

I don?t define these 2, not sure if it matters.

Quoted 4 lines

#define CONFIG_ENV_IS_IN_UBI
#define CONFIG_ENV_UBI_PART "ubi"
#define CONFIG_ENV_UBI_VOLUME "u-boot-env"
#define CONFIG_ENV_SIZE (64 * 1024)

My config looks like this:

#define MTDIDS_DEFAULT "nand0=xilinx_nand"

#define MTDPARTS_DEFAULT \
	"mtdparts=xilinx_nand:" \
		"128k(fsbl)ro," \
		"11M(u-boot)ro," \
		"70M(boot-config)," \
		"-(root)"

#define CONFIG_ENV_IS_IN_UBI
#define CONFIG_ENV_UBI_PART "boot-config" #define CONFIG_ENV_UBI_VOLUME "u-boot-env1" #define CONFIG_ENV_UBI_VOLUME_REDUND "u-boot-env2"
#define CONFIG_ENV_SIZE 0x20000

I create volumes like this:

	"writepartitions=" \
		"if ubi part boot-config && " \
			"ubi read $verifyaddr u-boot-env1 1 && " \
			"ubi read $verifyaddr u-boot-env2 1; " \
		"then " \
			"ubi remove bootfs && " \
			"ubi remove config; " \
		"else " \
			"nand erase.part boot-config && " \
			"ubi part boot-config && " \
			"ubi create u-boot-env1 " __stringify(CONFIG_ENV_SIZE) " dynamic && " \
			"ubi create u-boot-env2 " __stringify(CONFIG_ENV_SIZE) " dynamic; " \
		"fi && " \
		"ubi create bootfs " __stringify(CONFIG_BOOTFS_VOLUME_SIZE) " dynamic && " \
		"ubi create config - dynamic && " \
		"if ubi part root && " \
			"ubi read $verifyaddr rootfs 1; " \
		"then " \
			"ubi remove rootfs; " \
		"else " \
			"nand erase.part root && " \
			"ubi part root; " \
		"fi && " \
		"ubi create rootfs - dynamic;\0" \
Quoted 63 lines

=> ubi info
UBI: MTD device name: "mtd=1"
UBI: MTD device size: 510 MiB
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: number of good PEBs: 4072
UBI: number of bad PEBs: 8
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 2
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4072
UBI: number of PEBs reserved for bad PEB handling: 72
UBI: max/mean erase counter: 18/4

=> ubi info l
Volume information dump:

          vol_id          0
          reserved_pebs   1
          alignment       1
          data_pad        0
          vol_type        3
          name_len        10
          usable_leb_size 126976
          used_ebs        1
          used_bytes      126976
          last_eb_bytes   126976
          corrupted       0
          upd_marker      0
          name            u-boot-env
Volume information dump:
          vol_id          1
          reserved_pebs   3993
          alignment       1
          data_pad        0
          vol_type        3
          name_len        6
          usable_leb_size 126976
          used_ebs        3993
          used_bytes      507015168
          last_eb_bytes   126976
          corrupted       0
          upd_marker      0
          name            rootfs
Volume information dump:
          vol_id          2147479551
          reserved_pebs   2
          alignment       1
          data_pad        0
          vol_type        3
          name_len        13
          usable_leb_size 126976
          used_ebs        2
          used_bytes      253952
          last_eb_bytes   2
          corrupted       0
          upd_marker      0
          name            layout volume
Quoted 8 lines

=> ubifsmount ubi0:rootfs
Error reading superblock on volume 'ubi0:rootfs' errno=-30! ubifsmount - mount UBIFS volume

Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume

I also notice that you are not using a redundant env like I am, so maybe there is a bug when not using a redundant env that I don't run into.

GL,
-Joe

#3 lore raw

Hello Joe,

Am 11.05.2016 um 01:15 schrieb Joseph Hershberger:

Quoted 48 lines

Hi Kevin,

Am 09.05.2016 um 23:16 schrieb Kevin Smith:

Quoted 44 lines

Hello,

I would appreciate some UBI help/advice if you are able to provide it. I am trying to use UBI to store my u-boot environment, but when I try to 'saveenv', it is corrupting another volume of my UBI. I can image the rootfs volume and boot Linux from it without a problem. However, the first time that I save the u-boot environment, the rootfs becomes unreadable. When the rootfs is corrupted, I have booted Linux from another source and tried to attach UBI and dd out the data. It appears as all 0xFF. Both u-boot and Linux can read the env volume correctly.

I do not think that there is a board in U-boot that uses UBI env, so I do not have anything to compare to. I have included some details of my setup below. Do you have any suggestion about what might be wrong? I saw the recent patch b1d6590d35, and thought it might fix it, but am still having the problem even with this. Maybe there is another bug? I am glad to provide more info as needed.
Thank you,
Kevin

DTS:

flash at d0000 {
       num-cs = <1>;
       marvell,nand-keep-config;
       marvell,nand-enable-arbiter;
       nand-on-flash-bbt;
       nand-ecc-strength = <4>;
       nand-ecc-step-size = <512>;
       status = "okay";

       partition at 0 {
           label = "mvboot";
           reg = <0 0x200000>;
       };
       partition at 200000 {
           label = "ubi";
           reg = <0x200000 0x1fe00000>;
       };
};

Config:
#define MTDIDS_DEFAULT "nand0=pxa3xx_nand-0"
#define MTDPARTS_DEFAULT "mtdparts=pxa3xx_nand-0:2m(mvboot),-(ubi)" #define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS

Quoted 4 lines
Quoted 2 lines

#define CONFIG_MTD_UBI_FASTMAP
#define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT 1

I don?t define these 2, not sure if it matters.

This should be no problem ... but you (Kevin) may disable FASTMAP for a test?

Quoted 7 lines
Quoted 4 lines

#define CONFIG_ENV_IS_IN_UBI
#define CONFIG_ENV_UBI_PART "ubi"
#define CONFIG_ENV_UBI_VOLUME "u-boot-env"
#define CONFIG_ENV_SIZE (64 * 1024)

My config looks like this:

Quoted 7 lines

#define MTDIDS_DEFAULT "nand0=xilinx_nand"

#define MTDPARTS_DEFAULT \
	"mtdparts=xilinx_nand:" \
		"128k(fsbl)ro," \
		"11M(u-boot)ro," \
		"70M(boot-config)," \
		"-(root)"

You have 70MB for Env?

Quoted 24 lines

#define CONFIG_ENV_IS_IN_UBI
#define CONFIG_ENV_UBI_PART "boot-config" #define CONFIG_ENV_UBI_VOLUME "u-boot-env1" #define CONFIG_ENV_UBI_VOLUME_REDUND "u-boot-env2"
#define CONFIG_ENV_SIZE 0x20000

I create volumes like this:

	"writepartitions=" \
		"if ubi part boot-config && " \
			"ubi read $verifyaddr u-boot-env1 1 && " \
			"ubi read $verifyaddr u-boot-env2 1; " \
		"then " \
			"ubi remove bootfs && " \
			"ubi remove config; " \
		"else " \
			"nand erase.part boot-config && " \
			"ubi part boot-config && " \
			"ubi create u-boot-env1 " __stringify(CONFIG_ENV_SIZE) " dynamic && " \
			"ubi create u-boot-env2 " __stringify(CONFIG_ENV_SIZE) " dynamic; " \
		"fi && " \
		"ubi create bootfs " __stringify(CONFIG_BOOTFS_VOLUME_SIZE) " dynamic && " \
		"ubi create config - dynamic && " \
		"if ubi part root && " \
Quoted 44 lines
			"ubi read $verifyaddr rootfs 1; " \
		"then " \
			"ubi remove rootfs; " \
		"else " \
			"nand erase.part root && " \
			"ubi part root; " \
		"fi && " \
		"ubi create rootfs - dynamic;\0" \
Quoted 34 lines

=> ubi info
UBI: MTD device name: "mtd=1"
UBI: MTD device size: 510 MiB
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: number of good PEBs: 4072
UBI: number of bad PEBs: 8
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 2
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4072
UBI: number of PEBs reserved for bad PEB handling: 72
UBI: max/mean erase counter: 18/4

=> ubi info l
Volume information dump:

           vol_id          0
           reserved_pebs   1
           alignment       1
           data_pad        0
           vol_type        3
           name_len        10
           usable_leb_size 126976
           used_ebs        1
           used_bytes      126976
           last_eb_bytes   126976
           corrupted       0
           upd_marker      0
           name            u-boot-env

@Kevin: you have exactly one PEB for this volume ... may this is the problem? Can you try it with a Volume, which have more space?

Quoted 33 lines
Quoted 33 lines

Volume information dump:

           vol_id          1
           reserved_pebs   3993
           alignment       1
           data_pad        0
           vol_type        3
           name_len        6
           usable_leb_size 126976
           used_ebs        3993
           used_bytes      507015168
           last_eb_bytes   126976
           corrupted       0
           upd_marker      0
           name            rootfs
Volume information dump:
           vol_id          2147479551
           reserved_pebs   2
           alignment       1
           data_pad        0
           vol_type        3
           name_len        13
           usable_leb_size 126976
           used_ebs        2
           used_bytes      253952
           last_eb_bytes   2
           corrupted       0
           upd_marker      0
           name            layout volume

=> ubifsmount ubi0:rootfs
Error reading superblock on volume 'ubi0:rootfs' errno=-30! ubifsmount - mount UBIFS volume

Quoted 6 lines
Quoted 4 lines

Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume

I also notice that you are not using a redundant env like I am, so maybe there is a bug when not using a redundant env that I don't run into.

I don;t know.

bye,
Heiko

Signature · 2 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
#4 lore raw

Hi Joe and Heiko,

I tried disabling the fastmap options, and it appears to be related to these. With fastmap off, I am able two write without corrupting the other volume. It looks like it may specifically be the autoupdate feature, but I am still testing to be sure this is the case. I will let you know.

Thank you for your help,
Kevin

Quoted 199 lines · Heiko Schocher

Hello Joe,

Am 11.05.2016 um 01:15 schrieb Joseph Hershberger:

Quoted 49 lines

Hi Kevin,

Am 09.05.2016 um 23:16 schrieb Kevin Smith:

Quoted 45 lines

Hello,

I would appreciate some UBI help/advice if you are able to provide it. I am trying to use UBI to store my u-boot environment, but when I try to 'saveenv', it is corrupting another volume of my UBI. I can image the rootfs volume and boot Linux from it without a problem. However, the first time that I save the u-boot environment, the rootfs becomes unreadable. When the rootfs is corrupted, I have booted Linux from another source and tried to attach UBI and dd out the data. It appears as all 0xFF. Both u-boot and Linux can read the env volume correctly.

I do not think that there is a board in U-boot that uses UBI env, so I do not have anything to compare to. I have included some details of my setup below. Do you have any suggestion about what might be wrong? I saw the recent patch b1d6590d35, and thought it might fix it, but am still having the problem even with this. Maybe there is another bug? I am glad to provide more info as needed.
Thank you,
Kevin

DTS:

flash at d0000 {
       num-cs = <1>;
       marvell,nand-keep-config;
       marvell,nand-enable-arbiter;
       nand-on-flash-bbt;
       nand-ecc-strength = <4>;
       nand-ecc-step-size = <512>;
       status = "okay";

       partition at 0 {
           label = "mvboot";
           reg = <0 0x200000>;
       };
       partition at 200000 {
           label = "ubi";
           reg = <0x200000 0x1fe00000>;
       };
};

Config:
#define MTDIDS_DEFAULT "nand0=pxa3xx_nand-0"
#define MTDPARTS_DEFAULT "mtdparts=pxa3xx_nand-0:2m(mvboot),-(ubi)" #define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS

Quoted 4 lines
Quoted 2 lines

#define CONFIG_MTD_UBI_FASTMAP
#define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT 1

I don?t define these 2, not sure if it matters.

This should be no problem ... but you (Kevin) may disable FASTMAP for a test?

Quoted 7 lines
Quoted 4 lines

#define CONFIG_ENV_IS_IN_UBI
#define CONFIG_ENV_UBI_PART "ubi"
#define CONFIG_ENV_UBI_VOLUME "u-boot-env"
#define CONFIG_ENV_SIZE (64 * 1024)

My config looks like this:

Quoted 7 lines

#define MTDIDS_DEFAULT "nand0=xilinx_nand"

#define MTDPARTS_DEFAULT \
    "mtdparts=xilinx_nand:" \
        "128k(fsbl)ro," \
        "11M(u-boot)ro," \
        "70M(boot-config)," \
        "-(root)"

You have 70MB for Env?

Quoted 24 lines

#define CONFIG_ENV_IS_IN_UBI
#define CONFIG_ENV_UBI_PART "boot-config" #define CONFIG_ENV_UBI_VOLUME "u-boot-env1" #define CONFIG_ENV_UBI_VOLUME_REDUND "u-boot-env2"
#define CONFIG_ENV_SIZE 0x20000

I create volumes like this:

    "writepartitions=" \
        "if ubi part boot-config && " \
            "ubi read $verifyaddr u-boot-env1 1 && " \
            "ubi read $verifyaddr u-boot-env2 1; " \
        "then " \
            "ubi remove bootfs && " \
            "ubi remove config; " \
        "else " \
            "nand erase.part boot-config && " \
            "ubi part boot-config && " \
            "ubi create u-boot-env1 " __stringify(CONFIG_ENV_SIZE) "

dynamic && " \
"ubi create u-boot-env2 " __stringify(CONFIG_ENV_SIZE) "
dynamic; " \
"fi && " \
"ubi create bootfs " __stringify(CONFIG_BOOTFS_VOLUME_SIZE) "

Quoted 47 lines
dynamic && " \
        "ubi create config - dynamic && " \
        "if ubi part root && " \
            "ubi read $verifyaddr rootfs 1; " \
        "then " \
            "ubi remove rootfs; " \
        "else " \
            "nand erase.part root && " \
            "ubi part root; " \
        "fi && " \
        "ubi create rootfs - dynamic;\0" \
Quoted 34 lines

=> ubi info
UBI: MTD device name: "mtd=1"
UBI: MTD device size: 510 MiB
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: number of good PEBs: 4072
UBI: number of bad PEBs: 8
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 2
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4072
UBI: number of PEBs reserved for bad PEB handling: 72
UBI: max/mean erase counter: 18/4

=> ubi info l
Volume information dump:

           vol_id          0
           reserved_pebs   1
           alignment       1
           data_pad        0
           vol_type        3
           name_len        10
           usable_leb_size 126976
           used_ebs        1
           used_bytes      126976
           last_eb_bytes   126976
           corrupted       0
           upd_marker      0
           name            u-boot-env

@Kevin: you have exactly one PEB for this volume ... may this is the problem?
Can you try it with a Volume, which have more space?

Quoted 33 lines
Quoted 33 lines

Volume information dump:

           vol_id          1
           reserved_pebs   3993
           alignment       1
           data_pad        0
           vol_type        3
           name_len        6
           usable_leb_size 126976
           used_ebs        3993
           used_bytes      507015168
           last_eb_bytes   126976
           corrupted       0
           upd_marker      0
           name            rootfs
Volume information dump:
           vol_id          2147479551
           reserved_pebs   2
           alignment       1
           data_pad        0
           vol_type        3
           name_len        13
           usable_leb_size 126976
           used_ebs        2
           used_bytes      253952
           last_eb_bytes   2
           corrupted       0
           upd_marker      0
           name            layout volume

=> ubifsmount ubi0:rootfs
Error reading superblock on volume 'ubi0:rootfs' errno=-30! ubifsmount - mount UBIFS volume

Quoted 8 lines
Quoted 4 lines

Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume

I also notice that you are not using a redundant env like I am, so maybe there is a bug when not using a redundant env that I don't run into.

I don;t know.

bye,
Heiko

#5 lore raw

Hello Kevin,

Am 11.05.2016 um 17:54 schrieb Kevin Smith:

Quoted 7 lines

Hi Joe and Heiko,

I tried disabling the fastmap options, and it appears to be related to these. With fastmap off, I am able two write without corrupting the other volume. It looks like it may specifically be the autoupdate feature, but I am still testing to be sure this is the case. I will let you know.

Thanks for debugging into it!

Quoted 1 line

Thank you for your help,

You are welcome!

bye,
Heiko

Quoted 202 lines

Kevin

Quoted 199 lines · Heiko Schocher

Hello Joe,

Am 11.05.2016 um 01:15 schrieb Joseph Hershberger:

Quoted 49 lines

Hi Kevin,

Am 09.05.2016 um 23:16 schrieb Kevin Smith:

Quoted 45 lines

Hello,

I would appreciate some UBI help/advice if you are able to provide it. I am trying to use UBI to store my u-boot environment, but when I try to 'saveenv', it is corrupting another volume of my UBI. I can image the rootfs volume and boot Linux from it without a problem. However, the first time that I save the u-boot environment, the rootfs becomes unreadable. When the rootfs is corrupted, I have booted Linux from another source and tried to attach UBI and dd out the data. It appears as all 0xFF. Both u-boot and Linux can read the env volume correctly.

I do not think that there is a board in U-boot that uses UBI env, so I do not have anything to compare to. I have included some details of my setup below. Do you have any suggestion about what might be wrong? I saw the recent patch b1d6590d35, and thought it might fix it, but am still having the problem even with this. Maybe there is another bug? I am glad to provide more info as needed.
Thank you,
Kevin

DTS:

flash at d0000 {
        num-cs = <1>;
        marvell,nand-keep-config;
        marvell,nand-enable-arbiter;
        nand-on-flash-bbt;
        nand-ecc-strength = <4>;
        nand-ecc-step-size = <512>;
        status = "okay";

        partition at 0 {
            label = "mvboot";
            reg = <0 0x200000>;
        };
        partition at 200000 {
            label = "ubi";
            reg = <0x200000 0x1fe00000>;
        };
};

Config:
#define MTDIDS_DEFAULT "nand0=pxa3xx_nand-0"
#define MTDPARTS_DEFAULT "mtdparts=pxa3xx_nand-0:2m(mvboot),-(ubi)" #define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS

Quoted 4 lines
Quoted 2 lines

#define CONFIG_MTD_UBI_FASTMAP
#define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT 1

I don?t define these 2, not sure if it matters.

This should be no problem ... but you (Kevin) may disable FASTMAP for a test?

Quoted 7 lines
Quoted 4 lines

#define CONFIG_ENV_IS_IN_UBI
#define CONFIG_ENV_UBI_PART "ubi"
#define CONFIG_ENV_UBI_VOLUME "u-boot-env"
#define CONFIG_ENV_SIZE (64 * 1024)

My config looks like this:

Quoted 7 lines

#define MTDIDS_DEFAULT "nand0=xilinx_nand"

#define MTDPARTS_DEFAULT \
     "mtdparts=xilinx_nand:" \
         "128k(fsbl)ro," \
         "11M(u-boot)ro," \
         "70M(boot-config)," \
         "-(root)"

You have 70MB for Env?

Quoted 24 lines

#define CONFIG_ENV_IS_IN_UBI
#define CONFIG_ENV_UBI_PART "boot-config" #define CONFIG_ENV_UBI_VOLUME "u-boot-env1" #define CONFIG_ENV_UBI_VOLUME_REDUND "u-boot-env2"
#define CONFIG_ENV_SIZE 0x20000

I create volumes like this:

     "writepartitions=" \
         "if ubi part boot-config && " \
             "ubi read $verifyaddr u-boot-env1 1 && " \
             "ubi read $verifyaddr u-boot-env2 1; " \
         "then " \
             "ubi remove bootfs && " \
             "ubi remove config; " \
         "else " \
             "nand erase.part boot-config && " \
             "ubi part boot-config && " \
             "ubi create u-boot-env1 " __stringify(CONFIG_ENV_SIZE) "

dynamic && " \
"ubi create u-boot-env2 " __stringify(CONFIG_ENV_SIZE) "
dynamic; " \
"fi && " \
"ubi create bootfs " __stringify(CONFIG_BOOTFS_VOLUME_SIZE) "

Quoted 47 lines
dynamic && " \
         "ubi create config - dynamic && " \
         "if ubi part root && " \
             "ubi read $verifyaddr rootfs 1; " \
         "then " \
             "ubi remove rootfs; " \
         "else " \
             "nand erase.part root && " \
             "ubi part root; " \
         "fi && " \
         "ubi create rootfs - dynamic;\0" \
Quoted 34 lines

=> ubi info
UBI: MTD device name: "mtd=1"
UBI: MTD device size: 510 MiB
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: number of good PEBs: 4072
UBI: number of bad PEBs: 8
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 2
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4072
UBI: number of PEBs reserved for bad PEB handling: 72
UBI: max/mean erase counter: 18/4

=> ubi info l
Volume information dump:

            vol_id          0
            reserved_pebs   1
            alignment       1
            data_pad        0
            vol_type        3
            name_len        10
            usable_leb_size 126976
            used_ebs        1
            used_bytes      126976
            last_eb_bytes   126976
            corrupted       0
            upd_marker      0
            name            u-boot-env

@Kevin: you have exactly one PEB for this volume ... may this is the problem?
Can you try it with a Volume, which have more space?

Quoted 33 lines
Quoted 33 lines

Volume information dump:

            vol_id          1
            reserved_pebs   3993
            alignment       1
            data_pad        0
            vol_type        3
            name_len        6
            usable_leb_size 126976
            used_ebs        3993
            used_bytes      507015168
            last_eb_bytes   126976
            corrupted       0
            upd_marker      0
            name            rootfs
Volume information dump:
            vol_id          2147479551
            reserved_pebs   2
            alignment       1
            data_pad        0
            vol_type        3
            name_len        13
            usable_leb_size 126976
            used_ebs        2
            used_bytes      253952
            last_eb_bytes   2
            corrupted       0
            upd_marker      0
            name            layout volume

=> ubifsmount ubi0:rootfs
Error reading superblock on volume 'ubi0:rootfs' errno=-30! ubifsmount - mount UBIFS volume

Quoted 8 lines
Quoted 4 lines

Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume

I also notice that you are not using a redundant env like I am, so maybe there is a bug when not using a redundant env that I don't run into.

I don;t know.

bye,
Heiko

Signature · 2 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany