Skip to contentSkip to conversation

DFS fails with QCA6174 and QCA9377

DISCUSSION The Dark Avenger 2 participants 2 messages May 21, 2016 – May 23, 2016 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

Hello,

I'm currently trying to set-up an AP in the 5 GHz band. I have a QCA6174 (Killer 1525) and a QCA9377 adapter at hand.

Unfortunately, while both cards work otherwise well, e.g. I can create an AP in the 2.4 GHz range, ACS works, anything requiring DFS fails:

Quoted 1 line

hostapd v. 2.5:

-----
wlp4s0: DFS-CAC-START freq=5580 chan=116 sec_chan=1, width=1, seg0=122, seg1=0, cac_time=60s
nl80211: Start radar detection (CAC) 5580 MHz (ht_enabled=1, vht_enabled=1, bandwidth=80 MHz, cf1=5610 MHz, cf2=0 MHz)
nl80211: Failed to start radar detection: -16 (Device or resource busy)
DFS start_dfs_cac() failed, -1
-----
Needless to say that the same thing happens on other channel, too, and that there're no channels requiring no DFS. iw list
-----
...
* 5240 MHz [48] (20.0 dBm) (no IR)
* 5260 MHz [52] (20.0 dBm) (no IR, radar detection)

                          DFS state: usable (for 607 sec)
                          DFS CAC time: 60000 ms
                      ...

* 5700 MHz [140] (26.0 dBm) (no IR, radar detection)
DFS state: usable (for 607 sec)
DFS CAC time: 60000 ms
* 5720 MHz [144] (disabled)
...
------
I compiled kernel 4.5.3 with DFS support, as seems to be confirmed by dmesg (see dfs 1):
-----

[    6.020482] ath10k_pci 0000:04:00.0: firmware: direct-loading firmware ath10k/QCA6174/hw2.1/firmware-5.bin
[    6.020500] ath10k_pci 0000:04:00.0: qca6174 hw2.1 target 0x05010000 chip_id 0x003405ff sub 1a56:1525
[    6.020505] ath10k_pci 0000:04:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 1 testmode 0
[    6.021159] ath10k_pci 0000:04:00.0: firmware ver SW_RM.1.1.1-00157-QCARMSWPZ-1 api 5 features ignore-otp,no-4addr-pad crc32 10bf8e08
[    6.128659] ath10k_pci 0000:04:00.0: firmware: direct-loading firmware ath10k/QCA6174/hw2.1/board-2.bin
[    6.129021] ath10k_pci 0000:04:00.0: board_file api 2 bmi_id N/A crc32 ae2e275a
[    7.331373] ath10k_pci 0000:04:00.0: htt-ver 3.1 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1

-----
For completeness iw get reg
-----
country DE: DFS-ETSI

        (2400 - 2483 @ 40), (N/A, 20), (N/A)
        (5150 - 5250 @ 80), (N/A, 20), (N/A), NO-OUTDOOR
        (5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS
        (5470 - 5725 @ 160), (N/A, 26), (0 ms), DFS
        (57000 - 66000 @ 2160), (N/A, 40), (N/A)

-----
The only thing that worries me is that "iw list" does not report any "radar detect widths".|. |So, I am somewhat clueless where the problem lies. Is it driver, firmware, or something else?

Thanks

Roland

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw
Quoted 7 lines · The Dark Avenger

Hello,

I'm currently trying to set-up an AP in the 5 GHz band. I have a QCA6174 (Killer 1525) and a QCA9377 adapter at hand.

Unfortunately, while both cards work otherwise well, e.g. I can create an AP in the 2.4 GHz range, ACS works, anything requiring DFS fails:

[...]

Quoted 4 lines

The only thing that worries me is that "iw list" does not report any "radar detect widths".|.
|So, I am somewhat clueless where the problem lies. Is it driver, firmware, or something else?

I suspect hardware does not support it. Firmware already advertises no support for AP_DFS service and driver follows suit and does not define any radar_detect_widths in interface combinations for these chips.

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k