Skip to contentSkip to conversation

Siano SMS1140 problem

DISCUSSION [email protected] 2 participants 2 messages Dec 29, 2009 – Dec 31, 2009 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

Hi,
I've already worked with different adapters (Pinnacle 320E with em28xx, Intel CE9500B1, Hauppauge Nova-T Stick and SAA7134), and all have worked without big problem reading the howto I've found online; but now I've a new dvb-adapter, and it's a Siano SMS1140. I've found some howto, but I'm not able to get it working.
Here are the steps I've followed:
- downloaded latest v4l-dvb tree (hg clone http://linuxtv.org/hg/v4l-dvb);
- compiled the tree without error (cd v4l-dvb; make);
- installed the new module (make install);
- rebooted the system;
- downloaded firmwares for dvbt from "http://steventoth.net/linux/sms1xxx/" and copied the firmware (tried version from 01 to 03) as dvb_nova_12mhz_b0.inp (as requested in dmesg output) in /lib/modules/firmware.
When I plug the adpter dmesg seems ok, but no device will be created in /dev/dvb (dvb was not created too), so all program don't find dvb-t.
I've tried to search inside the code, but I've not found anything interesting for me.
The only informations I can add are:
- USB ID: 187f:0201;
- name in source code: SMS1XXX_BOARD_SIANO_NOVA_B (Siano Nova B Digital Receiver);
- dmesg output:
usb 1-7: new high speed USB device using ehci_hcd and address 7
usb 1-7: New USB device found, idVendor=187f, idProduct=0201
usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-7: Product: MDTV Receiver
usb 1-7: Manufacturer: MDTV Receiver
usb 1-7: configuration #1 chosen from 1 choice
usb 1-7: firmware: requesting dvb_nova_12mhz_b0.inp
smscore_set_device_mode: firmware download success: dvb_nova_12mhz_b0.inp
usbcore: registered new interface driver smsusb
- when I unplug the adapter and do "modprobe -r smsusb smsmdtv", in dmesg:
usb 1-7: USB disconnect, address 5
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
smsusb_onresponse: line: 74: error, urb status -108 (-ESHUTDOWN), 0 bytes
sms_ir_exit:
usbcore: deregistering interface driver smsusb

Someone can explain to me how to get it to work or where I miss something ori, if it's due to some regression, how to debug it and support a programmer for this?

Very thanks for the help in advance,
Sebastian

#1 lore raw

Sorry for the delay in replying... A spiffy new year everyone for whom calendars and clocks and daylight and seasons have meaning, and also to the rest of you living in your mum's basement.

Quoted 1 line · On Tue, 29 Dec 2009, [email protected] wrote:

I've already worked with different adapters (Pinnacle 320E with em28xx, Intel CE9500B1, Hauppauge Nova-T Stick and SAA7134), and all have worked without big problem reading the howto I've found online; but now I've a new dvb-adapter, and it's a Siano SMS1140.

I have a related, but different adapter, which until now I've just been using for DAB+ and DAB service reception, but I decided I'd check if there might be a regression in later kernels. Problem is I'm using a deliberately crippled machine, so that I don't trust all that I see. (Browser `lynx' tossing up kernel malloc failures I'd never seen before, for example) That aside,

Quoted 10 lines

- dmesg output:
usb 1-7: new high speed USB device using ehci_hcd and address 7 usb 1-7: New USB device found, idVendor=187f, idProduct=0201 usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-7: Product: MDTV Receiver
usb 1-7: Manufacturer: MDTV Receiver
usb 1-7: configuration #1 chosen from 1 choice
usb 1-7: firmware: requesting dvb_nova_12mhz_b0.inp
smscore_set_device_mode: firmware download success: dvb_nova_12mhz_b0.inp
usbcore: registered new interface driver smsusb

What I see in my first failed attempt is

[422523.242709] usb 3-2.2.1: firmware: requesting dvbt_bda_stellar_usb.inp
[422523.329911] smsusb: probe of 3-2.2.1:1.1 failed with error -71
[422523.331556] usbcore: registered new interface driver smsusb

Unfortunately, that prevents me from identifying at what point in the following sorta-successful attempt you would see the registration of the smsusb... And I am too lazy to unload those modules and try again :-)

Here is what I see after a successful load of the firmware, that the device disconnects, reconnects with a different ID, and then runs into further problems:

[422545.201374] usb 3-2.2.3: firmware: requesting dvbt_bda_stellar_usb.inp
[422545.468215] usb 3-2.2.3: USB disconnect, address 26
[422547.750697] usb 3-2.2.3: new full speed USB device using uhci_hcd and address 27
[422547.883683] usb 3-2.2.3: New USB device found, idVendor=187f, idProduct=0100[422547.883826] usb 3-2.2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[422547.883978] usb 3-2.2.3: Product: SMS DVBT-BDA Receiver
[422547.884095] usb 3-2.2.3: Manufacturer: Siano Mobile Silicon
[422547.886690] usb 3-2.2.3: configuration #1 chosen from 1 choice
[422548.012889] smsusb_onresponse: line: 116: error, urb status -84, 0 bytes

I am not sure if you should see the same thing (disconnect, reconnect with different ID from the firmware) with your particular device after firmware load.

In any case, the kernel version I had used for DAB+ reception is several versions back, and the last time I attempted to use this device for DVB-T is even older than that (no problems then, but on different hardware, with a lot fewer USB hubs in the path to cause problems).

I'd offer to see what I could do with the particular kernel source which gives me the above, except that I've already overwritten that source with newer.

Anyway, I will see what I can do with my device with either the newest kernel, or the older stable one which I've patched into usefulness, sometime in the coming days or weeks, and report any successes or failures (plus differences to the Siano library that supports the Eureka-147 DAB decoding, should that also fail).

Quoted 1 line

Someone can explain to me how to get it to work or where I miss something ori, if it's due to some regression, how to debug it and support a programmer for this?

This isn't much, but in the absence of any other replies, it's the best I can offer.

thanks,
barry bouwmsa