Skip to contentSkip to conversation

Problem in configuring buffer size of a memory pool

DISCUSSION Karthikraj palanichamy 2 participants 3 messages Feb 9, 2017

lore
Share & tools
lore
#0 lore raw

Hi developers,

For /rte_pktmbuf_pool_create(), /I normally provide RTE_MBUF_DEFAULT_BUF_SIZE as the data room size.

I needed to change this dynamically based on the frame size to be transmitted.
To transmit 80 bytes frames, I configured (80 +/RTE_PKTMBUF_HEADROOM/). There was no problem and transmission was successful.

Then I will do rte_mempool_free() and create mem pool again whenever needed.

So, my code flow is /create mempool -> transmit pkts -> free mempool/

When I do this for 3 to 5 times, I get segmentation fault in the transmission API of the PMD. - 'eth_igb_xmit_pkts' for igb PMD and 'ixgbe_xmit_pkts_vec()' for ixgbe PMD.

Thanks in advance for your help.

Regards
Karthik

DISCLAIMER: Privileged and/or Confidential information may be contained in this message. If you are not the addressee of this message, you may not copy, use or deliver this message to anyone. In such event,you should destroy the message and kindly notify the sender by reply e-mail.
It is understood that opinions or conclusions that do not relate to the official business of the company are neither given nor endorsed by the company.

#1 lore raw
Quoted 13 lines · Karthikraj palanichamy

Hi developers,

For /rte_pktmbuf_pool_create(), /I normally provide RTE_MBUF_DEFAULT_BUF_SIZE as the data room size.

I needed to change this dynamically based on the frame size to be transmitted.
To transmit 80 bytes frames, I configured (80 +/RTE_PKTMBUF_HEADROOM/). There was no problem and transmission was successful.

Then I will do rte_mempool_free() and create mem pool again whenever needed.

Quoted 8 lines

So, my code flow is /create mempool -> transmit pkts -> free mempool/

When I do this for 3 to 5 times, I get segmentation fault in the transmission API of the PMD. - 'eth_igb_xmit_pkts' for igb PMD and 'ixgbe_xmit_pkts_vec()' for ixgbe PMD.

Thanks in advance for your help.

I think you'll need to stop the transmit ports and possibly destroy and recreate the TX queues too. What may be happening is that packet buffers are remaining on the TX ring after transmit, and then when being freed to make room for new packet buffers to be transmitted, the mempool to which they are to be freed no longer exists.

Quoted 12 lines

Regards
Karthik

DISCLAIMER: Privileged and/or Confidential information may be contained in this message. If you are not the addressee of this message, you may not copy, use or deliver this message to anyone. In such event,you should destroy the message and kindly notify the sender by reply e-mail.
It is understood that opinions or conclusions that do not relate to the official business of the company are neither given nor endorsed by the company.

Since this is a public mailing list, please remove this disclaimer as the email cannot be private.

/Bruce

#2 lore raw

Thanks for the help.

I couldn't stop or close the device/port since Rx is a continuous process with a separate mempool. I'm creating dynamic mempools only for Tx.

Tried stopping the Tx queue 'rte_eth_dev_tx_queue_stop()' after freeing the mempool. Created mempool again and then started the tx queue.

Still observing the same problem.

Regards
Karthik

Quoted 40 lines · Bruce Richardson
Quoted 13 lines · Karthikraj palanichamy

Hi developers,

For /rte_pktmbuf_pool_create(), /I normally provide RTE_MBUF_DEFAULT_BUF_SIZE as the data room size.

I needed to change this dynamically based on the frame size to be transmitted.
To transmit 80 bytes frames, I configured (80 +/RTE_PKTMBUF_HEADROOM/). There was no problem and transmission was successful.

Then I will do rte_mempool_free() and create mem pool again whenever needed.

Quoted 8 lines

So, my code flow is /create mempool -> transmit pkts -> free mempool/

When I do this for 3 to 5 times, I get segmentation fault in the transmission API of the PMD. - 'eth_igb_xmit_pkts' for igb PMD and 'ixgbe_xmit_pkts_vec()' for ixgbe PMD.

Thanks in advance for your help.

I think you'll need to stop the transmit ports and possibly destroy and recreate the TX queues too. What may be happening is that packet buffers are remaining on the TX ring after transmit, and then when being freed to make room for new packet buffers to be transmitted, the mempool to which they are to be freed no longer exists.

Quoted 12 lines

Regards
Karthik

DISCLAIMER: Privileged and/or Confidential information may be contained in this message. If you are not the addressee of this message, you may not copy, use or deliver this message to anyone. In such event,you should destroy the message and kindly notify the sender by reply e-mail.
It is understood that opinions or conclusions that do not relate to the official business of the company are neither given nor endorsed by the company.

Quoted 5 lines

Since this is a public mailing list, please remove this disclaimer as the email cannot be private.

/Bruce

DISCLAIMER: Privileged and/or Confidential information may be contained in this message. If you are not the addressee of this message, you may not copy, use or deliver this message to anyone. In such event,you should destroy the message and kindly notify the sender by reply e-mail.
It is understood that opinions or conclusions that do not relate to the official business of the company are neither given nor endorsed by the company.