Skip to contentSkip to conversation

IPMI support on OpenBMC

DISCUSSION tomjose 2 participants 2 messages Sep 1, 2017 – Sep 4, 2017

lore
Share & tools
lore

tomjose

author
#0 lore raw

This mail is to solicit feedback on the IPMI implementation on OpenBMC and figure out if any important feature is missing. We have added support for IPMI over network(standard IPMI port) and the BT transfer. The first milestone we are trying to achieve is to have support for all the mandatory IPMI commands. Below is a snapshot of current situation based on feature and command support.

Supported Features:
---------------------------

-> Chassis Commands
-> SEL
-> FRU command
-> Serial Over LAN
-> Watchdog support
-> Sensor commands
-> Network Configuration
-> Boot Configuration

Work in Progress & Pending stuff:
-------------------------------------------

-> Full fledged SDR support
-> DCMI Compliance
-> User Management commands

Following is the list of the supported IPMI commands:

#<NetFn>:<Command

0x00:0x00    //<Chassis>:<Chassis Capabilities>
0x00:0x01    //<Chassis>:<Get Chassis Status>
0x00:0x02    //<Chassis>:<Chassis Control>
0x00:0x08    //<Chassis>:<Set System Boot Options>
0x00:0x09    //<Chassis>:<Get System Boot Options>
0x04:0x2D    //<Sensor/Event>:<Get Sensor Reading>
0x04:0x2F    //<Sensor/Event>:<Get Sensor Type>
0x04:0x30    //<Sensor/Event>:<Set Sensor Reading and Event Status>
0x06:0x01    //<App>:<Get Device ID>
0x06:0x02    //<App>:<Cold Reset>
0x06:0x03    //<App>:<Warm Reset>
0x06:0x04    //<App>:<Get Self Test Results>
0x06:0x08    //<App>:<Get Device GUID>
0x06:0x22    //<App>:<Reset Watchdog Timer>
0x06:0x24    //<App>:<Set Watchdog Timer>
0x06:0x2E    //<App>:<Set BMC Global Enables>
0x06:0x31    //<App>:<Get Message Flags>
0x06:0x35    //<App>:<Read Event Message Buffer>
0x06:0x36    //<App>:<Get BT Interface Capabilities>
0x06:0x40    //<App>:<Set Channel Access>
0x06:0x41    //<App>:<Get Channel Access>
0x06:0x42    //<App>:<Get Channel Info Command>
0x0A:0x10    //<Storage>:<Get FRU Inventory Area Info>
0x0A:0x11    //<Storage>:<Read FRU Data>
0x0A:0x12    //<Storage>:<Write FRU Data>
0x0A:0x40    //<Storage>:<Get SEL Info>
0x0A:0x42    //<Storage>:<Reserve SEL>
0x0A:0x44    //<Storage>:<Add SEL Entry>
0x0A:0x48    //<Storage>:<Get SEL Time>
0x0A:0x49    //<Storage>:<Set SEL Time>
0x0C:0x01    //<Transport>:<Set LAN Configuration Parameters>
0x0C:0x02    //<Transport>:<Get LAN Configuration Parameters>
0x2C:0x00    //<Group Extension>:<Group Extension Command>
0x2C:0x03    //<Group Extension>:<Get Power Limit>
0x2C:0x04    //<Group Extension>:<Set Power Limit>
0x2C:0x05    //<Group Extension>:<Activate/Deactivate Power Limit>
0x2C:0x06    //<Group Extension>:<Get Asset Tag>
0x2C:0x08    //<Group Extension>:<Set Asset Tag>

Regards,
Tom

#1 lore raw
Quoted 8 lines · tomjose

This mail is to solicit feedback on the IPMI implementation on OpenBMC and figure out if any important feature is missing.
We have added support for IPMI over network(standard IPMI port) and the BT transfer. The first milestone we are trying to
achieve is to have support for all the mandatory IPMI commands. Below is a snapshot of current situation based on feature
and command support.

Quoted 4 lines

Supported Features:
---------------------------

-> Chassis Commands

Do we support the following:

power soft
power on
power off
power reset

Last I tested this the behaviour did not match expectations established from other platforms.

Cheers,

Joel

Quoted 61 lines

-> SEL
-> FRU command
-> Serial Over LAN
-> Watchdog support
-> Sensor commands
-> Network Configuration
-> Boot Configuration

Work in Progress & Pending stuff:
-------------------------------------------

-> Full fledged SDR support
-> DCMI Compliance
-> User Management commands

Following is the list of the supported IPMI commands:

#<NetFn>:<Command

0x00:0x00    //<Chassis>:<Chassis Capabilities>
0x00:0x01    //<Chassis>:<Get Chassis Status>
0x00:0x02    //<Chassis>:<Chassis Control>
0x00:0x08    //<Chassis>:<Set System Boot Options>
0x00:0x09    //<Chassis>:<Get System Boot Options>
0x04:0x2D    //<Sensor/Event>:<Get Sensor Reading>
0x04:0x2F    //<Sensor/Event>:<Get Sensor Type>
0x04:0x30    //<Sensor/Event>:<Set Sensor Reading and Event Status>
0x06:0x01    //<App>:<Get Device ID>
0x06:0x02    //<App>:<Cold Reset>
0x06:0x03    //<App>:<Warm Reset>
0x06:0x04    //<App>:<Get Self Test Results>
0x06:0x08    //<App>:<Get Device GUID>
0x06:0x22    //<App>:<Reset Watchdog Timer>
0x06:0x24    //<App>:<Set Watchdog Timer>
0x06:0x2E    //<App>:<Set BMC Global Enables>
0x06:0x31    //<App>:<Get Message Flags>
0x06:0x35    //<App>:<Read Event Message Buffer>
0x06:0x36    //<App>:<Get BT Interface Capabilities>
0x06:0x40    //<App>:<Set Channel Access>
0x06:0x41    //<App>:<Get Channel Access>
0x06:0x42    //<App>:<Get Channel Info Command>
0x0A:0x10    //<Storage>:<Get FRU Inventory Area Info>
0x0A:0x11    //<Storage>:<Read FRU Data>
0x0A:0x12    //<Storage>:<Write FRU Data>
0x0A:0x40    //<Storage>:<Get SEL Info>
0x0A:0x42    //<Storage>:<Reserve SEL>
0x0A:0x44    //<Storage>:<Add SEL Entry>
0x0A:0x48    //<Storage>:<Get SEL Time>
0x0A:0x49    //<Storage>:<Set SEL Time>
0x0C:0x01    //<Transport>:<Set LAN Configuration Parameters>
0x0C:0x02    //<Transport>:<Get LAN Configuration Parameters>
0x2C:0x00    //<Group Extension>:<Group Extension Command>
0x2C:0x03    //<Group Extension>:<Get Power Limit>
0x2C:0x04    //<Group Extension>:<Set Power Limit>
0x2C:0x05    //<Group Extension>:<Activate/Deactivate Power Limit>
0x2C:0x06    //<Group Extension>:<Get Asset Tag>
0x2C:0x08    //<Group Extension>:<Set Asset Tag>

Regards,
Tom