Skip to contentSkip to conversation

SPL variant of sunxi nand module

U-Boot Nikolai Zhubr 2 participants 8 messages Dec 23, 2018 – Dec 29, 2018

lore
Share & tools
lore
#0 lore raw

Hi all,

While fighting with this A20-olinuxino nand boot process I've initially found that some essential nand-related parameters are apparently missing by default, preventing reasonable nand operation, so I started debugging this gradually.

Quoted 4 lines

U-Boot SPL 2019.01-rc2 (Dec 20 2018 - 16:30:46 +0300)

CPU: 912000000Hz, AXI/AHB/APB: 3/2/2

DRAM: 1024 MiB
Trying to boot from NAND

Now I've discovered that SPL-build variant of sunxi_nand module is missing the sunxi_nand_init() whatsoever. Apparently it is on purpose, because:

#ifndef CONFIG_SPL_BUILD
         sunxi_nand_init();

#endif

And I cannot simply un-ifdef sunxi_nand_init() here, because the SPL build would fail with undefined symbol then, but I'm wondering, where are all values (like ECC strength and such) are expected to come from instead? Is SPL nand loader is supposed to be usable at all currently?

Thank you,

Regards,
Nikolai

#1 lore raw

Hi again,

Quoted 5 lines · 23.12.2018 16:29, I wrote:
Quoted 4 lines

U-Boot SPL 2019.01-rc2 (Dec 20 2018 - 16:30:46 +0300)

CPU: 912000000Hz, AXI/AHB/APB: 3/2/2

DRAM: 1024 MiB
Trying to boot from NAND

Ok, discovered a special SPL-only sunxi_nand_spl variant, added some debugging, so the detection is visible:

In nand_detect_config(), start detection... Considering addr_cycles=5, page_size=2048
Considering ecc_size=1024, ecc_strength=0 failed(a).
Considering addr_cycles=5, page_size=2048 rejected. Considering addr_cycles=5, page_size=4096
Considering ecc_size=1024, ecc_strength=3 failed(a).
Considering addr_cycles=5, page_size=4096 rejected. Considering addr_cycles=5, page_size=8192
Considering ecc_size=1024, ecc_strength=4 good(b).
Considering addr_cycles=5, page_size=8192 accepted.

I'm almost 100% sure that correct config would be page_size=8192, ecc_size=1024, ecc_strength=40 (from nand chip identification structure for regular linux kernel)

Now the detection routine in sunxi_nand_spl apparently comes up with a value of ecc_strength=4 instead... Why is that?

Thank you,

Regards,
Nikolai

Quoted 10 lines

Thank you,

Regards,
Nikolai
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#2 lore raw

Hi

Quoted 24 lines · Nikolai Zhubr

Hi again,

Quoted 5 lines · 23.12.2018 16:29, I wrote:
Quoted 4 lines

U-Boot SPL 2019.01-rc2 (Dec 20 2018 - 16:30:46 +0300)

CPU: 912000000Hz, AXI/AHB/APB: 3/2/2

DRAM: 1024 MiB
Trying to boot from NAND

Ok, discovered a special SPL-only sunxi_nand_spl variant, added some debugging, so the detection is visible:

In nand_detect_config(), start detection... Considering addr_cycles=5, page_size=2048
Considering ecc_size=1024, ecc_strength=0 failed(a).
Considering addr_cycles=5, page_size=2048 rejected. Considering addr_cycles=5, page_size=4096
Considering ecc_size=1024, ecc_strength=3 failed(a).
Considering addr_cycles=5, page_size=4096 rejected. Considering addr_cycles=5, page_size=8192
Considering ecc_size=1024, ecc_strength=4 good(b).
Considering addr_cycles=5, page_size=8192 accepted.

Quoted 3 lines

I'm almost 100% sure that correct config would be page_size=8192, ecc_size=1024, ecc_strength=40 (from nand chip identification structure for regular linux kernel)

That is an index on an array. Am I wrong? so the max is 74

Michael

Quoted 3 lines

Now the detection routine in sunxi_nand_spl apparently comes up with a value of ecc_strength=4 instead... Why is that?

n - 1 using an index, if the code that I have is aligned so

Michael

Quoted 23 lines

Thank you,

Regards,
Nikolai

Quoted 10 lines

Thank you,

Regards,
Nikolai
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 4 lines
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |
#3 lore raw

Hi Michael,

23.12.2018 18:54, Michael Nazzareno Trimarchi:
[...]

Quoted 8 lines
Quoted 6 lines
   Considering ecc_size=1024, ecc_strength=4 good(b).

Considering addr_cycles=5, page_size=8192 accepted.

I'm almost 100% sure that correct config would be page_size=8192, ecc_size=1024, ecc_strength=40 (from nand chip identification structure for regular linux kernel)

That is an index on an array. Am I wrong? so the max is 74

Indeed, its an index, and therefore it appears SPL's detection actually gives correct values! Nevertheless, SPL reads all zeroes from nand.

On the other hand, normal U-boot variant reads correct data from nand, but I'm not yet sure if it uses correct parameters and specifically, if they match those of SPL version. Need to add yet more debugging output.

Thank you,

Regards,
Nikolai

Quoted 36 lines

Michael

Quoted 3 lines

Now the detection routine in sunxi_nand_spl apparently comes up with a value of ecc_strength=4 instead... Why is that?

n - 1 using an index, if the code that I have is aligned so

Michael

Quoted 23 lines

Thank you,

Regards,
Nikolai

Quoted 10 lines

Thank you,

Regards,
Nikolai
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#4 lore raw

Hi again,

23.12.2018 21:11, I wrote:
[...]

Quoted 2 lines

Indeed, its an index, and therefore it appears SPL's detection actually gives correct values! Nevertheless, SPL reads all zeroes from nand.

Regarding the sunxi_nand_spl.c module, I can not find any mention if it implies NAND_ECC_HW, NAND_ECC_HW_SYNDROME, or rather some other mode, or if these modes are irrelevant in this case?

Can not guess browsing through the code, it looks too different from sunxi_nand.c to compare.

Thank you,

Regards,
Nikolai

Quoted 51 lines

On the other hand, normal U-boot variant reads correct data from nand, but I'm not yet sure if it uses correct parameters and specifically, if they match those of SPL version. Need to add yet more debugging output.

Thank you,

Regards,
Nikolai

Quoted 36 lines

Michael

Quoted 3 lines

Now the detection routine in sunxi_nand_spl apparently comes up with a value of ecc_strength=4 instead... Why is that?

n - 1 using an index, if the code that I have is aligned so

Michael

Quoted 23 lines

Thank you,

Regards,
Nikolai

Quoted 10 lines

Thank you,

Regards,
Nikolai
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#5 lore raw

23.12.2018 21:58, I wrote:
[...]

Quoted 3 lines

Regarding the sunxi_nand_spl.c module, I can not find any mention if it implies NAND_ECC_HW, NAND_ECC_HW_SYNDROME, or rather some other mode, or if these modes are irrelevant in this case?

So far I'm observing that sunxi_nand_spl module refuses to load erased nand pages (500000 in the example below), which is correct, but it "successfully" loads filled nand pages as totally zeroed out, which is supposedly incorrect. This is in contrast with sunxi_nand module, that loads filled pages correctly, at least in my simple tests.

So while detection in sunxi_nand_spl seems fine, reading seems not.

I think digging deeper without some additional advice is a bit beyond my capabilities, although most probably some very tiny bits are missing...

Thank you,

Regards,
Nikolai

U-Boot SPL 2019.01-rc2 (Dec 23 2018 - 23:23:57 +0300)

CPU: 912000000Hz, AXI/AHB/APB: 3/2/2

DRAM: 1024 MiB

Quoted 1 line
Quoted 1 line

SPL: board_init_r()

Trying to boot from NAND
spl: nand - using hw ecc
[zh]nand_spl_load_image(500000, 40)=-22
[zh]Read dump of page 768 (nand offs 600000, page_size 8192):
0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,
[zh]Read dump of page 768 (nand offs 600000, page_size 8192):
0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,
=====================================================
U-Boot 2019.01-rc2 (Dec 23 2018 - 22:30:35 +0300) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)
Model: Olimex A20-Olinuxino Micro
I2C:   ready
DRAM:  1 GiB
NAND:  nand_base: device found, Manufacturer ID: 0xad, Chip ID: 0xd7
nand_base: Hynix H27UBG8T2BTR-BC 32G 3.3V 8-bit
nand_base: Hynix H27UBG8T2BTR-BC 32G 3.3V 8-bit
nand_base: 4096 MiB, MLC, erase size: 2048 KiB, page size: 8192, OOB 
size: 640
Using ECC step 1024, strength 40, mode 2
4096 MiB
In:    serial
Out:   serial
Err:   serial
SCSI:  SATA link 0 timeout.

AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst

Net:   Can't get reset: -524
eth0: ethernet at 1c50000
Hit any key to stop autoboot:  0

=> nand read 0x45000000 0x400000 0x1000

NAND read: device 0 offset 0x400000, size 0x1000 Scanning device for bad blocks
Bad eraseblock 0 at 0x0000001fe000
Bad eraseblock 1 at 0x0000003fe000
4096 bytes read: OK
=> md.b 0x45000000 100
45000000: b8 00 00 ea 14 f0 9f e5 14 f0 9f e5 14 f0 9f e5
................
=====================================================

Quoted 63 lines

Can not guess browsing through the code, it looks too different from sunxi_nand.c to compare.

Thank you,

Regards,
Nikolai

Quoted 51 lines

On the other hand, normal U-boot variant reads correct data from nand, but I'm not yet sure if it uses correct parameters and specifically, if they match those of SPL version. Need to add yet more debugging output.

Thank you,

Regards,
Nikolai

Quoted 36 lines

Michael

Quoted 3 lines

Now the detection routine in sunxi_nand_spl apparently comes up with a value of ecc_strength=4 instead... Why is that?

n - 1 using an index, if the code that I have is aligned so

Michael

Quoted 23 lines

Thank you,

Regards,
Nikolai

Quoted 10 lines

Thank you,

Regards,
Nikolai
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#6 lore raw

Hi again,

The following commit (titled "use PIO instead of DMA") apparently broke actual reading of nand pages in SPL at least for A20:

http://git.denx.de/?p=u-boot.git;a=commit;h=6ddbb1e936c78cdef1e7395039fa7020c5c75326

Instead of reading page contents, non-dma (current) version just feeds zeroes here.
Tested on A20-olinuxino-micro with a Hynix 4GB nand chip.

It'd be nice to somehow fix it back eventually :)

Other than that, nand boot seems usable (with added necessary chip id).

Thank you,

Regards,
Nikolai

Quoted 134 lines · 24.12.2018 0:00, I wrote:

23.12.2018 21:58, I wrote:
[...]

Quoted 3 lines

Regarding the sunxi_nand_spl.c module, I can not find any mention if it implies NAND_ECC_HW, NAND_ECC_HW_SYNDROME, or rather some other mode, or if these modes are irrelevant in this case?

So far I'm observing that sunxi_nand_spl module refuses to load erased nand pages (500000 in the example below), which is correct, but it "successfully" loads filled nand pages as totally zeroed out, which is supposedly incorrect. This is in contrast with sunxi_nand module, that loads filled pages correctly, at least in my simple tests.

So while detection in sunxi_nand_spl seems fine, reading seems not.

I think digging deeper without some additional advice is a bit beyond my capabilities, although most probably some very tiny bits are missing...

Thank you,

Regards,
Nikolai

U-Boot SPL 2019.01-rc2 (Dec 23 2018 - 23:23:57 +0300)

CPU: 912000000Hz, AXI/AHB/APB: 3/2/2

DRAM: 1024 MiB

Quoted 1 line
Quoted 1 line

SPL: board_init_r()

Trying to boot from NAND
spl: nand - using hw ecc
[zh]nand_spl_load_image(500000, 40)=-22
[zh]Read dump of page 768 (nand offs 600000, page_size 8192):
0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,
[zh]Read dump of page 768 (nand offs 600000, page_size 8192):
0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,
=====================================================
U-Boot 2019.01-rc2 (Dec 23 2018 - 22:30:35 +0300) Allwinner Technology

CPU: Allwinner A20 (SUN7I)
Model: Olimex A20-Olinuxino Micro
I2C: ready
DRAM: 1 GiB
NAND: nand_base: device found, Manufacturer ID: 0xad, Chip ID: 0xd7
nand_base: Hynix H27UBG8T2BTR-BC 32G 3.3V 8-bit
nand_base: Hynix H27UBG8T2BTR-BC 32G 3.3V 8-bit
nand_base: 4096 MiB, MLC, erase size: 2048 KiB, page size: 8192, OOB
size: 640
Using ECC step 1024, strength 40, mode 2
4096 MiB
In: serial
Out: serial
Err: serial
SCSI: SATA link 0 timeout.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst

Net: Can't get reset: -524
eth0: ethernet at 1c50000
Hit any key to stop autoboot: 0
=> nand read 0x45000000 0x400000 0x1000

NAND read: device 0 offset 0x400000, size 0x1000
Scanning device for bad blocks
Bad eraseblock 0 at 0x0000001fe000
Bad eraseblock 1 at 0x0000003fe000
4096 bytes read: OK
=> md.b 0x45000000 100
45000000: b8 00 00 ea 14 f0 9f e5 14 f0 9f e5 14 f0 9f e5 ................
=====================================================

Quoted 63 lines

Can not guess browsing through the code, it looks too different from sunxi_nand.c to compare.

Thank you,

Regards,
Nikolai

Quoted 51 lines

On the other hand, normal U-boot variant reads correct data from nand, but I'm not yet sure if it uses correct parameters and specifically, if they match those of SPL version. Need to add yet more debugging output.

Thank you,

Regards,
Nikolai

Quoted 36 lines

Michael

Quoted 3 lines

Now the detection routine in sunxi_nand_spl apparently comes up with a value of ecc_strength=4 instead... Why is that?

n - 1 using an index, if the code that I have is aligned so

Michael

Quoted 23 lines

Thank you,

Regards,
Nikolai

Quoted 10 lines

Thank you,

Regards,
Nikolai
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#7 lore raw

Hi,

Its just to remind sunxi_nand_spl.c is still broken. (And probably has been for a couple releases or so).
I'm unable to fix it myself (other than reverting the mentioned commit locally.)

Thank you,

Regards,
Nikolai

24.12.2018 0:47, Nikolai Zhubr:

Quoted 22 lines

Hi again,

The following commit (titled "use PIO instead of DMA") apparently broke actual reading of nand pages in SPL at least for A20:

http://git.denx.de/?p=u-boot.git;a=commit;h=6ddbb1e936c78cdef1e7395039fa7020c5c75326

Instead of reading page contents, non-dma (current) version just feeds zeroes here.
Tested on A20-olinuxino-micro with a Hynix 4GB nand chip.

It'd be nice to somehow fix it back eventually :)

Other than that, nand boot seems usable (with added necessary chip id).

Thank you,

Regards,
Nikolai