Advanced QoS camera traffic inside VPN on Asus router
Hello List,
I have a difficult QoS issue to solve on a DSL-AC52U router. I have some ip cameras on a network which send out massive traffic to a video server on another side of a layer 2 VPN.
This VPN carries other data SSH/RDP/VNC which needs to be prioritized over the ip camera traffic and to complicate things
there are regular network protocols which are non-vpn SSH/RDP/VNC again and pretty much everything else which also
needs to be prioritized against the camera traffic.
Is this even possible to merge the queue of 2 interfaces into one and prioritize by that?
To make it even more complex the traffic from the Camera-(ra0 2Ghz wifi)
Quoted 1 line
VPN (tap15) is bridged.
# brctl show
bridge name bridge id STP enabled interfaces
br0 8000.d017c30d90f0 no ra0
elan.1
elan.2
elan.3
elan.4
rai0
tap15Therefore the packets never enter the mangle chain.
I don't care about any services on the camera therefore I could just put that whole IP to the lowest priority QoS queue.
For example:
iptables -t mangle -I FORWARD -s 10.0.0.10 -j MARK --set-mark 1 iptables -t mangle -I PREROUTING -s 10.0.0.10 -j MARK --set-mark 1
Has absolutely no effect.
ebtables -I FORWARD -p IPv4 -o tap15+ -s 00:18:39:6b:ab:12 -j DROP
works using the camera's Wifi mac:
Bridge chain: FORWARD, entries: 1, policy: ACCEPT
-p IPv4 -s 0:18:39:6b:ab:12 -o tap15+ -j DROP , pcnt = 160 -- bcnt = 35702
Ebtables however it seems is not able to mark the packets :( It has an option: mark - "Matches frames with the given unsigned mark value." but it is a matching not marking.
What is the best solution/workaround for this issue?
The only one I can think of is to setup a second VPN tunnel between the 2 locations (same router<>same server) on a different port and put that second VPN tunnel into the lowest priority traffic.
Quoted 11 lines · Daniel Santos
Hello List,
I have a difficult QoS issue to solve on a DSL-AC52U router. I have some ip cameras on a network which send out massive traffic to a video server on another side of a layer 2 VPN.
This VPN carries other data SSH/RDP/VNC which needs to be prioritized over the ip camera traffic and to complicate things
there are regular network protocols which are non-vpn SSH/RDP/VNC again and pretty much everything else which also
needs to be prioritized against the camera traffic.
Quoted 2 lines
Is this even possible to merge the queue of 2 interfaces into one and prioritize by that?
In theory you could try ifb with traffic directed to it from > 1 interface by adding tc rules on those interfaces.
On egress first add eg. prio on said interfaces just so you can add tc rules (default pfifo_fast won't allow this)
I haven't done this on such a complicated setup, but try searching around for examples, it may work for you.
Consider turning off GRO/TSO/whatever with ethtool so you see real rather than aggregated packets.
I haven't tried for ages, so don't have any hard examples. It should be possible to mark with tc actions, the actual classification you do on a redirect to ifb type rule
doesn't get seen by a qdisc on ifb, it is reinstated when(if) the packet returns.
Quoted 47 lines
To make it even more complex the traffic from the Camera-(ra0 2Ghz wifi)
Quoted 1 line
VPN (tap15) is bridged.
# brctl show bridge name bridge id STP enabled interfaces br0 8000.d017c30d90f0 no ra0 elan.1 elan.2 elan.3 elan.4 rai0 tap15Therefore the packets never enter the mangle chain.
I don't care about any services on the camera therefore I could just put that whole IP to the lowest priority QoS queue.For example:
iptables -t mangle -I FORWARD -s 10.0.0.10 -j MARK --set-mark 1 iptables -t mangle -I PREROUTING -s 10.0.0.10 -j MARK --set-mark 1
Has absolutely no effect.
ebtables -I FORWARD -p IPv4 -o tap15+ -s 00:18:39:6b:ab:12 -j DROP
works using the camera's Wifi mac:
Bridge chain: FORWARD, entries: 1, policy: ACCEPT
-p IPv4 -s 0:18:39:6b:ab:12 -o tap15+ -j DROP , pcnt = 160 -- bcnt = 35702Ebtables however it seems is not able to mark the packets :( It has an option: mark - "Matches frames with the given unsigned mark value." but it is a matching not marking.
What is the best solution/workaround for this issue?
The only one I can think of is to setup a second VPN tunnel between the 2 locations (same router<>same server) on a different port and put that second VPN tunnel into the lowest priority traffic.
Signature · 3 lines
To unsubscribe from this list: send the line "unsubscribe lartc" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html