Question of Lost Dbus
Hi Everyone,
I have some problem about that when i using some ipmi commands, it will return "Unspecified error",
and after I tracing code in phoshpor-ipmi-host package, I find that there are some Dubs doesn't create in our openbmc system.
Most of them are network relational Dbus, and here is the Dbus list which do not create in our system:
Netwotk:
xyz.openbmc_project.Network.SystemConfiguration
xyz.openbmc_project.Network.EthernetInterface
xyz.openbmc_project.Network.IP
xyz.openbmc_project.Network.IP.Create
xyz.openbmc_project.Network.MACAddress
xyz.openbmc_project.Network.Neighbor
xyz.openbmc_project.Network.Neighbor.CreateStatic
xyz.openbmc_project.Network.VLAN
xyz.openbmc_project.Network.VLAN.Create
ACPI:
xyz.openbmc_project.Control.Power.ACPIPowerState
Chassis Capabilities:
xyz.openbmc_project.Control.ChassisCapabilities
And here are only two network relational Dbus in our system:
Service xyz.openbmc_project.Network:
└─/xyz
└─/xyz/openbmc_project
└─/xyz/openbmc_project/network
├─/xyz/openbmc_project/network/config
│ └─/xyz/openbmc_project/network/config/dhcp
├─/xyz/openbmc_project/network/eth0
│ ├─/xyz/openbmc_project/network/eth0/ipv4
│ │ └─/xyz/openbmc_project/network/eth0/ipv4/8e1bfa2f
│ └─/xyz/openbmc_project/network/eth0/ipv6
│ └─/xyz/openbmc_project/network/eth0/ipv6/bc41eef6
├─/xyz/openbmc_project/network/eth1
│ ├─/xyz/openbmc_project/network/eth1/ipv4
│ │ └─/xyz/openbmc_project/network/eth1/ipv4/1c4a187f
│ └─/xyz/openbmc_project/network/eth1/ipv6
│ └─/xyz/openbmc_project/network/eth1/ipv6/73a2a5d0
├─/xyz/openbmc_project/network/sit0
└─/xyz/openbmc_project/network/usb0
└─/xyz/openbmc_project/network/usb0/ipv4
└─/xyz/openbmc_project/network/usb0/ipv4/caca0d1dService xyz.openbmc_project.Network.SNMP:
└─/xyz
└─/xyz/openbmc_project
└─/xyz/openbmc_project/network
└─/xyz/openbmc_project/network/snmp
└─/xyz/openbmc_project/network/snmp/managerAre there some packages i losing to add into our system?
Feel free to give your comments, thank you.
Sincerely,
Spencer Ku
Spencer,
You might need to define your channel config file in phosphor-ipmi-config and add channel for network.
Regards
-Vijay
From: openbmc <[email protected]> on behalf of "Spencer Ku (古世瑜)" <[email protected]>
Date: Monday, March 30, 2020 at 11:45 PM
To: "[email protected]" <[email protected]>
Subject: Question of Lost Dbus
Hi Everyone,
I have some problem about that when i using some ipmi commands, it will return "Unspecified error",
and after I tracing code in phoshpor-ipmi-host package, I find that there are some Dubs doesn't create in our openbmc system.
Most of them are network relational Dbus, and here is the Dbus list which do not create in our system:
Netwotk:
xyz.openbmc_project.Network.SystemConfiguration
xyz.openbmc_project.Network.EthernetInterface
xyz.openbmc_project.Network.IP
xyz.openbmc_project.Network.IP.Create
xyz.openbmc_project.Network.MACAddress
xyz.openbmc_project.Network.Neighbor
xyz.openbmc_project.Network.Neighbor.CreateStatic
xyz.openbmc_project.Network.VLAN
xyz.openbmc_project.Network.VLAN.Create
ACPI:
xyz.openbmc_project.Control.Power.ACPIPowerState
Chassis Capabilities:
xyz.openbmc_project.Control.ChassisCapabilities
And here are only two network relational Dbus in our system:
Service xyz.openbmc_project.Network:
└─/xyz
└─/xyz/openbmc_project
└─/xyz/openbmc_project/network
├─/xyz/openbmc_project/network/config
│ └─/xyz/openbmc_project/network/config/dhcp
├─/xyz/openbmc_project/network/eth0
│ ├─/xyz/openbmc_project/network/eth0/ipv4
│ │ └─/xyz/openbmc_project/network/eth0/ipv4/8e1bfa2f
│ └─/xyz/openbmc_project/network/eth0/ipv6
│ └─/xyz/openbmc_project/network/eth0/ipv6/bc41eef6
├─/xyz/openbmc_project/network/eth1
│ ├─/xyz/openbmc_project/network/eth1/ipv4
│ │ └─/xyz/openbmc_project/network/eth1/ipv4/1c4a187f
│ └─/xyz/openbmc_project/network/eth1/ipv6
│ └─/xyz/openbmc_project/network/eth1/ipv6/73a2a5d0
├─/xyz/openbmc_project/network/sit0
└─/xyz/openbmc_project/network/usb0
└─/xyz/openbmc_project/network/usb0/ipv4
└─/xyz/openbmc_project/network/usb0/ipv4/caca0d1dService xyz.openbmc_project.Network.SNMP:
└─/xyz
└─/xyz/openbmc_project
└─/xyz/openbmc_project/network
└─/xyz/openbmc_project/network/snmp
└─/xyz/openbmc_project/network/snmp/managerAre there some packages i losing to add into our system?
Feel free to give your comments, thank you.
Sincerely,
Spencer Ku
Hi Vijay,
Thank you for the comments. Channel config has already defined in our system,
actually most of ipmi commands can work normally. The config in our system like below:
"0" : {
"name" : "IPMB",
"is_valid" : true,
"active_sessions" : 0,
"channel_info" : {
"medium_type" : "ipmb",
"protocol_type" : "ipmb-1.0",
"session_supported" : "session-less",
"is_ipmi" : true
}
},
"1" : {
"name" : "eth0",
"is_valid" : true,
"active_sessions" : 0,
"channel_info" : {
"medium_type" : "lan-802.3",
"protocol_type" : "ipmb-1.0",
"session_supported" : "multi-session",
"is_ipmi" : true
}
},
"2" : {
"name" : "eth1",
"is_valid" : true,
"active_sessions" : 0,
"channel_info" : {
"medium_type" : "lan-802.3",
"protocol_type" : "ipmb-1.0",
"session_supported" : "multi-session",
"is_ipmi" : true
}
But some lan configuration commands like “IPv6 Static Addresses” will use following DBus:
xyz.openbmc_project.Network.IP.Create
Since our system doesn’t have that Dbus, the setting will fail.
“Chassis capabilities” and ACPI command also have the same problem.
So I want to know that are there some settings or packages I lost.
Thank you.
Sincerely,
Spencer Ku
From: Vijay Khemka <[email protected]>
Sent: Wednesday, April 1, 2020 12:58 AM
To: Spencer Ku (古世瑜) <[email protected]>; [email protected]
Subject: Re: Question of Lost Dbus
Spencer,
You might need to define your channel config file in phosphor-ipmi-config and add channel for network.
Regards
-Vijay
From: openbmc <[email protected]<mailto:[email protected]>> on behalf of "Spencer Ku (古世瑜)" <[email protected]<mailto:[email protected]>>
Date: Monday, March 30, 2020 at 11:45 PM
To: "[email protected]<mailto:[email protected]>" <[email protected]<mailto:[email protected]>>
Subject: Question of Lost Dbus
Hi Everyone,
I have some problem about that when i using some ipmi commands, it will return "Unspecified error",
and after I tracing code in phoshpor-ipmi-host package, I find that there are some Dubs doesn't create in our openbmc system.
Most of them are network relational Dbus, and here is the Dbus list which do not create in our system:
Netwotk:
xyz.openbmc_project.Network.SystemConfiguration
xyz.openbmc_project.Network.EthernetInterface
xyz.openbmc_project.Network.IP
xyz.openbmc_project.Network.IP.Create
xyz.openbmc_project.Network.MACAddress
xyz.openbmc_project.Network.Neighbor
xyz.openbmc_project.Network.Neighbor.CreateStatic
xyz.openbmc_project.Network.VLAN
xyz.openbmc_project.Network.VLAN.Create
ACPI:
xyz.openbmc_project.Control.Power.ACPIPowerState
Chassis Capabilities:
xyz.openbmc_project.Control.ChassisCapabilities
And here are only two network relational Dbus in our system:
Service xyz.openbmc_project.Network:
└─/xyz
└─/xyz/openbmc_project
└─/xyz/openbmc_project/network
├─/xyz/openbmc_project/network/config
│ └─/xyz/openbmc_project/network/config/dhcp
├─/xyz/openbmc_project/network/eth0
│ ├─/xyz/openbmc_project/network/eth0/ipv4
│ │ └─/xyz/openbmc_project/network/eth0/ipv4/8e1bfa2f
│ └─/xyz/openbmc_project/network/eth0/ipv6
│ └─/xyz/openbmc_project/network/eth0/ipv6/bc41eef6
├─/xyz/openbmc_project/network/eth1
│ ├─/xyz/openbmc_project/network/eth1/ipv4
│ │ └─/xyz/openbmc_project/network/eth1/ipv4/1c4a187f
│ └─/xyz/openbmc_project/network/eth1/ipv6
│ └─/xyz/openbmc_project/network/eth1/ipv6/73a2a5d0
├─/xyz/openbmc_project/network/sit0
└─/xyz/openbmc_project/network/usb0
└─/xyz/openbmc_project/network/usb0/ipv4
└─/xyz/openbmc_project/network/usb0/ipv4/caca0d1d
Service xyz.openbmc_project.Network.SNMP:
└─/xyz
└─/xyz/openbmc_project
└─/xyz/openbmc_project/network
└─/xyz/openbmc_project/network/snmp
└─/xyz/openbmc_project/network/snmp/manager
Are there some packages i losing to add into our system?
Feel free to give your comments, thank you.
Sincerely,
Spencer Ku