ARM: Add ADS7846 touchscreen support to Overo platform
Subsystems (3)
An upcoming Overo expansion board includes an ADS7846 touchscreen controller.
This patch adds support via the ads7846 driver when enabled in the kernel config.
Signed-off-by Steve Sakoman <[email protected]>
--- arch/arm/mach-omap2/board-overo.c | 61 +++++++++++++++++++++++++ arch/arm/plat-omap/include/mach/board-overo.h | 1 + 2 files changed, 62 insertions(+), 0 deletions(-)
(quoted diff) +0 -0
b/arch/arm/mach-omap2/board-overo.c
index 032a2c9..2521b21 100644
arch/arm/mach-omap2/board-overo.c +61 -0
73 lines not on this page · raw message
(quoted diff) +0 -0
b/arch/arm/plat-omap/include/mach/board-overo.h
index 8635171..aca717d 100644
arch/arm/plat-omap/include/mach/board-overo.h +1 -0
@@ -18,6 +18,7 @@#define OVERO_GPIO_BT_XGATE 15#define OVERO_GPIO_W2W_NRESET 16 +#define OVERO_GPIO_PENDOWN 114#define OVERO_GPIO_BT_NRESET 164#define OVERO_GPIO_USBH_CPEN 168#define OVERO_GPIO_USBH_NRESET 183
Signature · 1 line
1.5.6.3
Tony Lindgren
maintainerQuoted 4 lines · Steve Sakoman
An upcoming Overo expansion board includes an ADS7846 touchscreen controller.
This patch adds support via the ads7846 driver when enabled in the kernel config.
Adding this also to omap3-upstream and linux-omap.
Tony
Quoted 105 lines
Signed-off-by Steve Sakoman <[email protected]>--- arch/arm/mach-omap2/board-overo.c | 61 +++++++++++++++++++++++++ arch/arm/plat-omap/include/mach/board-overo.h | 1 + 2 files changed, 62 insertions(+), 0 deletions(-)arch/arm/mach-omap2/board-overo.c +61
-0@@ -116,6 +116,66 @@ static inline void __init overo_init_smsc911x(void)static inline void __init overo_init_smsc911x (void ) {return ; }#endif +#if defined(CONFIG_TOUCHSCREEN_ADS7846 ) || \ + defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE ) + +#include <mach/mcspi.h> +#include <linux/spi/spi.h> +#include <linux/spi/ads7846.h> + +static struct omap2_mcspi_device_config ads7846_mcspi_config = { + .turbo_mode =0 , + .single_channel =1 ,/* 0: slave, 1: master */ +}; + + +static int ads7846_get_pendown_state (void ) +{ +return !gpio_get_value (OVERO_GPIO_PENDOWN ); +} + +static struct ads7846_platform_data ads7846_config = { + .x_max =0x0fff , + .y_max =0x0fff , + .x_plate_ohms =180 , + .pressure_max =255 , + .debounce_max =10 , + .debounce_tol =3 , + .debounce_rep =1 , + .get_pendown_state = ads7846_get_pendown_state, + .keep_vref_on =1 , +}; + +static struct spi_board_info overo_spi_board_info[]__initdata = { + { + .modalias ="ads7846" , + .bus_num =1 , + .chip_select =0 , + .max_speed_hz =1500000 , + .controller_data = &ads7846_mcspi_config, + .irq =OMAP_GPIO_IRQ (OVERO_GPIO_PENDOWN ), + .platform_data = &ads7846_config, + } +}; + +static void __init overo_ads7846_init (void ) +{ +if ((gpio_request (OVERO_GPIO_PENDOWN ,"ADS7846_PENDOWN" ) ==0 ) && + (gpio_direction_input (OVERO_GPIO_PENDOWN ) ==0 )) { +gpio_export (OVERO_GPIO_PENDOWN ,0 ); + }else { +printk (KERN_ERR "could not obtain gpio for ADS7846_PENDOWN\n" ); +return ; + } + +spi_register_board_info (overo_spi_board_info, +ARRAY_SIZE (overo_spi_board_info)); +} + +#else +static inline void __init overo_ads7846_init (void ) {return ; } +#endif +static struct mtd_partition overo_nand_partitions[] = { { .name ="xloader" ,@@ -296,6 +356,7 @@ static void __init overo_init(void)usb_ehci_init ();overo_flash_init ();overo_init_smsc911x (); +overo_ads7846_init (); if ((gpio_request(OVERO_GPIO_W2W_NRESET, "OVERO_GPIO_W2W_NRESET") == 0) &&arch/arm/plat-omap/include/mach/board-overo.h +1
-0@@ -18,6 +18,7 @@#define OVERO_GPIO_BT_XGATE 15#define OVERO_GPIO_W2W_NRESET 16 +#define OVERO_GPIO_PENDOWN 114#define OVERO_GPIO_BT_NRESET 164#define OVERO_GPIO_USBH_CPEN 168#define OVERO_GPIO_USBH_NRESET 183Signature · 5 lines
1.5.6.3 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html