mesh: Add mesh conf for SAR Transmitter and Receiver
PATCH 2/4 mesh: Add mesh conf for SAR Transmitter and Receiver
This allows you to set the SAR Transitter state and SAR Receiver state in the mesh conf file.
--- mesh/mesh-main.conf | 107 ++++++++++++++++++++++++++++++++++++++++++++ mesh/mesh.c | 80 ++++++++++++++++++++++++++++++--- 2 files changed, 181 insertions(+), 6 deletions(-)
mesh/mesh-main.conf +107 -0
@@ -41,3 +41,110 @@ # Setting this value to zero means there's no timeout. # Defaults to 60. #ProvTimeout = 60 + + +[SARTransmitter] + +# Transmission interval step between segments of a message. +# Interval is measured in milliseconds and calculated using the following +# formula: +# +# (SegIntervalStep + 1) * 10 ms. +# +# Valid range 0-15. +# Defaults to 5. +#SegIntervalStep = 5 + +# Maximum number of retransmissions of segments to a unicast destination. +# Valid range 0-15. +# Defaults to 2. +#UnicastRetransCount = 2 + +# Maximum number of retransmissions of segments to a unicast destination when no +# acknowledgment is newly received during the retransmission interval. +# This value sould be set to greater than AckRetransCount on a peer node. +# Valid range 0-15. +# Defaults to 2. +#UnicastRetransWithoutProgressCount = 2 + +# Retransmission interval step between segments of a meesage to a unicast +# destination. +# Interval is measured in milliseconds and calculated using the following +# formula: +# +# (UnicastRetransIntervalStep + 1) * 25 ms +# +# Valid range 0-15. +# Defaults to 7. +#UnicastRetransIntervalStep = 7 + +# Interval step between segments of a message to a unicast destination that +# increases proportionally to (ttl - 1) when ttl is over 0. +# Increment is measured in milliseconds and calculated using the following +# formula: +# +# (UnicastRetransIntervalIncrement + 1) * 25 ms +# +# Valid range 0-15. +# Defaults to 1. +#UnicastRetransIntervalIncrement = 1 + +# Maximum number of retransmissions of segments to a multicast destination. +# Valid range 0-15. +# Defaults to 2. +#MulticastRetransCount = 2 + +# Retransmission interval step between segments of a meesage to a multicast +# destination. +# Interval is measured in milliseconds and calculated using the following +# formula: +# +# (MulticastRetransIntervalStep + 1) * 25 ms +# +# Valid range 0-15. +# Defaults to 8. +#MulticastRetransIntervalStep = 8 + +[SARReceiver] + +# Threshold number of segments in a message to retransmit acknowledgment +# messages. If the number of segments in a message exceeds SegmentsThreshold, +# retransmit the Acknowledgment message by AckRetransCount. +# Valid range 0-31. +# Defaults to 3 +#SegmentsThreshold = 3 + +# Interval increment between acknowledgment messages. +# Increment is measured in segments and calculated using the following formula: +# +# AckDelayIncrement + 1.5 +# +# Valid range 0-7 +# Defaults to 1 +#AckDelayIncrement = 1 + +# Maximum number of retransmissions of acknowledgment messages. +# Valid range 0-3 +# Defaults to 0 +#AckRetransCount = 0 + +# Timeout to discard a segmented message when no more new segments of the +# message are coming in. +# Timeout is measured in seconds and calculated using the following formula: +# +# (DiscardTimeout + 1) * 5 sec +# +# Valid range 0-15 +# Defaults to 1 +#DiscardTimeout = 1 + +# Interval between received segments of a message. This is used to control rate +# of transmission of acknowledgment messages. +# Increment is measured in milliseconds and calculated using the following +# formula: +# +# (ReceiverSegIntervalStep + 1) * 10 ms +# +# Valid range 0-15 +# Defaults to 5 +#ReceiverSegIntervalStep = 5
mesh/mesh.c +74 -6
96 lines not on this page · raw message
Signature · 1 line
2.34.1