Skip to contentSkip to conversation

mesh: Add mesh conf for SAR Transmitter and Receiver

PATCH Superseded Junho Lee 1 participant 1 message Oct 14, 2024 Bluetooth drivers

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Junho Lee

author
#0 lore raw

PATCH v2 2/4 mesh: Add mesh conf for SAR Transmitter and Receiver

This allows you to set the SAR Transitter state and SAR Receiver state in the mesh conf file.

---
 mesh/mesh-main.conf | 107 ++++++++++++++++++++++++++++++++++++++++++++
 mesh/mesh.c         |  80 ++++++++++++++++++++++++++++++---
 2 files changed, 181 insertions(+), 6 deletions(-)
mesh/mesh-main.conf +107 -0
index aca9e6fa5..01f4c3d23 100644
@@ -41,3 +41,110 @@
 # Setting this value to zero means there's no timeout.
 # Defaults to 60.
 #ProvTimeout = 60
+
+
+[SARTransmitter]
+
+# Transmission interval step between segments of a message.
+# Interval is measured in milliseconds and calculated using the following
+# formula:
+#
+#   (SegIntervalStep + 1) * 10 ms.
+#
+# Valid range 0-15.
+# Defaults to 5.
+#SegIntervalStep = 5
+
+# Maximum number of retransmissions of segments to a unicast destination.
+# Valid range 0-15.
+# Defaults to 2.
+#UnicastRetransCount = 2
+
+# Maximum number of retransmissions of segments to a unicast destination when no
+# acknowledgment is newly received during the retransmission interval.
+# This value sould be set to greater than AckRetransCount on a peer node.
+# Valid range 0-15.
+# Defaults to 2.
+#UnicastRetransWithoutProgressCount = 2
+
+# Retransmission interval step between segments of a meesage to a unicast
+# destination.
+# Interval is measured in milliseconds and calculated using the following
+# formula:
+#
+#   (UnicastRetransIntervalStep + 1) * 25 ms
+#
+# Valid range 0-15.
+# Defaults to 7.
+#UnicastRetransIntervalStep = 7
+
+# Interval step between segments of a message to a unicast destination that
+# increases proportionally to (ttl - 1) when ttl is over 0.
+# Increment is measured in milliseconds and calculated using the following
+# formula:
+#
+#   (UnicastRetransIntervalIncrement + 1) * 25 ms
+#
+# Valid range 0-15.
+# Defaults to 1.
+#UnicastRetransIntervalIncrement = 1
+
+# Maximum number of retransmissions of segments to a multicast destination.
+# Valid range 0-15.
+# Defaults to 2.
+#MulticastRetransCount = 2
+
+# Retransmission interval step between segments of a meesage to a multicast
+# destination.
+# Interval is measured in milliseconds and calculated using the following
+# formula:
+#
+#   (MulticastRetransIntervalStep + 1) * 25 ms
+#
+# Valid range 0-15.
+# Defaults to 8.
+#MulticastRetransIntervalStep = 8
+
+[SARReceiver]
+
+# Threshold number of segments in a message to retransmit acknowledgment
+# messages. If the number of segments in a message exceeds SegmentsThreshold,
+# retransmit the Acknowledgment message by AckRetransCount.
+# Valid range 0-31.
+# Defaults to 3
+#SegmentsThreshold = 3
+
+# Interval increment between acknowledgment messages.
+# Increment is measured in segments and calculated using the following formula:
+#
+#   AckDelayIncrement + 1.5
+#
+# Valid range 0-7
+# Defaults to 1
+#AckDelayIncrement = 1
+
+# Maximum number of retransmissions of acknowledgment messages.
+# Valid range 0-3
+# Defaults to 0
+#AckRetransCount = 0
+
+# Timeout to discard a segmented message when no more new segments of the
+# message are coming in.
+# Timeout is measured in seconds and calculated using the following formula:
+#
+#   (DiscardTimeout + 1) * 5 sec
+#
+# Valid range 0-15
+# Defaults to 1
+#DiscardTimeout = 1
+
+# Interval between received segments of a message. This is used to control rate
+# of transmission of acknowledgment messages.
+# Increment is measured in milliseconds and calculated using the following
+# formula:
+#
+#   (ReceiverSegIntervalStep + 1) * 10 ms
+#
+# Valid range 0-15
+# Defaults to 5
+#ReceiverSegIntervalStep = 5
mesh/mesh.c +74 -6

96 lines not on this page · raw message

Signature · 1 line
2.34.1