drm/msm: dpu: Allow planes to extend past active display
Quoted 115 lines · Sean Paul
Quoted 8 lines · Jeykumar Sankaran
Quoted 7 lines · Sean Paul
From: Sean Paul <[email protected]>
The
atomic_checkis a bit too aggressive with respect to planes which leave the active area. This caused a bunch of log spew when the cursor got to the edge of the screen and stopped it from going all the way.This patch removes the conservative bounds checks from atomic and
clips
Quoted 61 lines
Quoted 61 lines
the dst rect such that we properly display planes which go off the screen.
Cc Sravanthi Kollukuduru <[email protected]>Signed-off-by Sean Paul <[email protected]>--- drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c | 3 +-- drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 10 +++++++--- 2 files changed, 8 insertions(+), 5 deletions(-)drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c +1
-2@@ -1551,8 +1551,7 @@ static int dpu_crtc_atomic_check(struct drm_crtc *crtc, cnt++; dst =drm_plane_state_dest (pstate); -if (!drm_rect_intersect (&clip, &dst) || - !drm_rect_equals (&clip, &dst)) { +if (!drm_rect_intersect (&clip, &dst)) {DPU_ERROR ("invalid vertical/horizontal destination\n");drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c +0
-0DPU_ERROR("display: " DRM_RECT_FMT " plane: " DRM_RECT_FMT "\n",
DRM_RECT_ARG(&crtc_rect),drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c +1
-1@@ -1254,7 +1254,7 @@ static int dpu_plane_sspp_atomic_update(structdrm_plane *plane, const struct dpu_format *fmt;struct drm_crtc *crtc;struct drm_framebuffer *fb; -struct drm_rect src, dst; +struct drm_rect clip = {0 }, src, dst;if (!plane) {drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c +4
-0DPU_ERROR ("invalid plane\n" );@@ -1300,14 +1300,18 @@ static int dpu_plane_sspp_atomic_update(structdrm_plane *plane, dst =drm_plane_state_dest (state); + clip.x2 = crtc->state->adjusted_mode.hdisplay; + clip.y2 = crtc->state->adjusted_mode.vdisplay; +drm_rect_intersect (&clip, &dst); + DPU_DEBUG_PLANE(pdpu, "FB[%u] " DRM_RECT_FMT "->crtc%u "
DRM_RECT_FMT
", %4.4s ubwc %d\n",fb->base.id,DRM_RECT_ARG(&src),drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c +1
-1- crtc->base.id,DRM_RECT_ARG (&dst), + crtc->base.id,DRM_RECT_ARG (&clip), (char *)&fmt->base.pixel_format, DPU_FORMAT_IS_UBWC(fmt));Quoted 8 lines
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
Quoted 3 lines
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c +1
-1pdpu->pipe_cfg.src_rect = src; - pdpu->pipe_cfg.dst_rect = dst; + pdpu->pipe_cfg.dst_rect = clip;If clip width/height is not equal to dst(which will be same as src for cursor)
width/height it will require scaling which is not supported by DMA pipe (used for cursor planes).It doesn't require scaling, it just requires that the scanout stops short.
Perhaps some ascii-art will explain better. This is what u/s is trying to do:
+----------------------+ | active display | | | | +---------+ | | plane | | | | | +---------+ | | +----------------------+This is what the patch does:
+----------------------+ | active display | | | | +---+ | | p| | | | | +---+ | | +----------------------+So we're not scaling anything, just stopping short. On my device, the first
scenario results in immediate blue screen when the cursor exits the active area
(underrun?). With the patch, it works just fine since everything is confined to
the screen.
Quoted 1 line
Sean
In order to stop the scanout at the boundary and partially display the cursor image, you should be clipping both the src and dst rects.
e.g if the source dimension is 100 x 100 and the original dst rect is 100 x 100 (no scaling). If you are clipping the dst to 50 x 100 and keeping the original src image, you are basically scaling down the image from 100 x 100 to 50 x 100.
Thanks and Regards,
Jeykumar S.
Quoted 13 lines
Quoted 3 lines
Ideally, we should suppress the error log and reset the cursor x/y to
w/h
Quoted 9 lines
offset from the boundaries.
Jeykumar S.
Quoted 2 lines
_dpu_plane_setup_scaler(pdpu, pstate, fmt, false);--
Jeykumar S
Signature · 5 lines
Jeykumar S _______________________________________________ Freedreno mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/freedreno