Skip to contentSkip to conversation

alsa drivers running under latest Mac Pro hw (MacPro 3, 1, quad core)

DISCUSSION S. Aguinaga 1 participant 1 message Aug 21, 2008

lore
Share & tools
lore
#0 lore raw

Stan & Takashi,

Still no luck when adding the mode=macpro option to the file:

cat /etc/modprobe.d/sound
options snd-hda-intel model=macpro

The sys module: /sys/module/snd_hda_intel/parameters/model shows:
cat model macpro,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>

Attached are screen-captures of the volume meter showing no options and the Volume control showing no streams available.

// Salvador

----- Original Message ----
From: Takashi Iwai <[email protected]>
To: S. Aguinaga <[email protected]>
Cc: [email protected]
Sent: Tuesday, August 19, 2008 5:48:47 AM
Subject: Re: [alsa-devel] Alsa-devel Digest, Vol 18, Issue 45

At Mon, 18 Aug 2008 10:26:42 -0700 (PDT),

Quoted 6 lines · S. Aguinaga

==============================================
Trying to figure out where to add this "model=macpro"
and it looks like it should be in a file called modprobe.conf or an options file under /etc/modprobe.d/

but I don't have (with my installation -- fedora {9} ) those files, do you have any input on this?

You can create any file, typically, /etc/modprobe.d/sound or so. Put the following line there

options snd-hda-intel model=macpro

Then reload the module, check the sysfs file /sys/modules/snd_hda_intel/parameters/macpro to see whether the specified option was really passed properly.

Takashi

Quoted 48 lines

below are the only files I have.

/etc/modprobe.d/

anaconda
blacklist-visor
i915modeset
blacklist
floppy-pnp
modprobe.conf.dist

==============================================
Subject: Re: [alsa-devel] Alsa-devel Digest, Vol 18, Issue 45

At Sat, 16 Aug 2008 06:15:46 -0700 (PDT),

Quoted 11 lines · S. Aguinaga
Quoted 9 lines · S. Aguinaga

Hello Stan,

This is awesome I did find the problem it's listed in the /var/log/messages under ALSA.

1.   When I bring up the "Pulse Volume Control" gui, the first tab "Playback"  comes up empty, and grayed-out is "No Streams Available"
2.   aplay does not produce sound, period!
3.   Amrok's welcome sample does not produce sound out of the std tower speaker or the headphone jack.
Quoted 6 lines
Quoted 6 lines

I didn't notice anything strange on the output of the alsa-info.sh file, but when I checked the var/log/messages, this is what I found:

sudo cat /var/log/messages | grep ALSA

Aug 11 07:52:10 macprolinx kernel: ALSA sound/pci/hda/hda_intel.c:1810: chipset global capabilities = 0x4401
Aug 11 07:52:10 macprolinx kernel: ALSA sound/pci/hda/hda_intel.c:749: codec_mask = 0x1
Aug 11 07:52:10 macprolinx kernel: ALSA sound/pci/hda/hda_codec.c:1073: Cannot find slave Surround Playback Volume, skipped

(snip)

These messages are harmless. It's just information from the driver, enabled only when you build it with CONFIG_SND_DEBUG_VERBOSE=y.

Quoted 5 lines

I think your problem is a misidentification of your sound chip. The model being used for your 889A appears to be incompatible, thus all the errors above. It appears that the macpro ALC885 is being selected before it gets to the choice for the ALC889A. Perhaps a developer can look into this.

Well, ALC882, ALC885 and ALC889A are almost compatible. In the driver, they are all handled in the same routine.

Quoted 11 lines

There are a few models for intel macs with ALC88x. Try to specify either model=macpro, model=mbp3 or model=imac24 as the module option of snd-hda-intel driver.

Takashi

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel