Skip to contentSkip to conversation

Booting 2.6.30-rc2-git7 very slow

DISCUSSION Martin Knoblauch 1 participant 1 message Apr 22, 2009

lore
Share & tools
lore
#0 lore raw

----- Original Message ----

Quoted 34 lines

From: Rafael J. Wysocki <[email protected]>
To: Martin Knoblauch <[email protected]>
Cc: [email protected]
Sent: Tuesday, April 21, 2009 9:12:20 PM
Subject: Re: Booting 2.6.30-rc2-git7 very slow

Quoted 4 lines · Martin Knoblauch

Hi, [please CC me on replies, as I am not subscribed]

booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit userspace)

is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:

Quoted 6 lines
[   14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  254.476493] Microcode Update Driver: v2.00 , 

Peter Oruba

Quoted 14 lines
[  254.718489] Microcode Update Driver: v2.00 removed.

So, we see 60 seconds for eaoch of the CPUs

[  255.273426] tg3 0000:03:01.0: PME# disabled
[  257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  257.833775] tg3: eth0: Flow control is off for TX and off for RX.
[  269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[  329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[  329.640463] eth1: TSO capability disabled.
[  329.640487] tg3 0000:03:01.1: PME# disabled
[  333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[  333.081759] tg3: eth1: Flow control is off for TX and off for RX.
Quoted 6 lines
Quoted 3 lines

We see 60 seconds for eth1, complaining about a failed firmware load.
/lib/firmware/tigon/tg3_tso.bin does exist and is from the current build.

Do I assume correctly that 2.6.29 did not have this problem?

I can tell that 2.6.28.2 did not have that problem. I skipped 2.6.29, so I cannot be sure. This is from the 2.6.28.2 boot sequence:

[   14.148605] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   14.194728] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   14.226354] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   14.258677] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   14.291483] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[   14.530193] Microcode Update Driver: v2.00 removed.
[   17.629690] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[   17.629695] tg3: eth0: Flow control is off for TX and off for RX.
[   33.328198] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[   33.328203] tg3: eth1: Flow control is off for TX and off for RX.
[   44.737601] RPC: Registered udp transport module.
[   44.737606] RPC: Registered tcp transport module.
[   47.637782] warning: process `snmpd' used the deprecated sysctl system call with 7.2.1.
[   57.671627] warning: `ntpd' uses 32-bit capabilities (legacy support in use)

Cheers
Martin