Skip to contentSkip to conversation

Booting 2.6.30-rc2-git7 very slow

DISCUSSION Martin Knoblauch 1 participant 1 message Apr 22, 2009

lore
Share & tools
lore
#0 lore raw

----- Original Message ----

Quoted 53 lines

From: Martin Knoblauch <[email protected]>
To: Rafael J. Wysocki <[email protected]>
Cc: [email protected]
Sent: Wednesday, April 22, 2009 11:56:27 AM
Subject: Re: Booting 2.6.30-rc2-git7 very slow

Quoted 12 lines

From: Rafael J. Wysocki

To: Martin Knoblauch
Cc: [email protected]
Sent: Tuesday, April 21, 2009 9:12:20 PM
Subject: Re: Booting 2.6.30-rc2-git7 very slow

Quoted 4 lines · Martin Knoblauch

Hi, [please CC me on replies, as I am not subscribed]

booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit

userspace)

Quoted 1 line

is much slower that it used to be. It seems I run into timeouts when [trying

to]

Quoted 22 lines

load intel and tg3 microcodes:

Quoted 6 lines
[   14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  254.476493] Microcode Update Driver: v2.00 , 

Peter Oruba

Quoted 14 lines
[  254.718489] Microcode Update Driver: v2.00 removed.

So, we see 60 seconds for eaoch of the CPUs

[  255.273426] tg3 0000:03:01.0: PME# disabled
[  257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  257.833775] tg3: eth0: Flow control is off for TX and off for RX.
[  269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[  329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[  329.640463] eth1: TSO capability disabled.
[  329.640487] tg3 0000:03:01.1: PME# disabled
[  333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[  333.081759] tg3: eth1: Flow control is off for TX and off for RX.
Quoted 6 lines
Quoted 3 lines

We see 60 seconds for eth1, complaining about a failed firmware load.
/lib/firmware/tigon/tg3_tso.bin does exist and is from the current build.

Do I assume correctly that 2.6.29 did not have this problem?

Just checked. 2.6.29 has exactely the same problem. 2.6.28.2 was OK. This is from the 2.6.29 boot:

Quoted 6 lines
[   14.308340] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   74.304612] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  134.304651] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  194.304638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  254.304597] Microcode Update Driver: v2.00 ,  Peter Oruba
[  254.546200] Microcode Update Driver: v2.00 removed.

In case of the platform microcode, the delays happen when doing:

/sbin/modprobe microcode

from the init script. I have a "microcode.dat" File in both /etc/ and /etc/firmware.

Quoted 11 lines
[  255.088405] tg3 0000:03:01.0: PME# disabled
[  257.669617] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  257.669622] tg3: eth0: Flow control is off for TX and off for RX.
[  269.456132] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[  329.456495] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[  329.456500] eth1: TSO capability disabled.
[  329.456524] tg3 0000:03:01.1: PME# disabled
[  332.921832] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[  332.921837] tg3: eth1: Flow control is off for TX and off for RX.

Thanks
Martin