oops when plugging CDC USB network device...
When plugging a Motorola SurfBoard 5100 device into my box, khubd oopses. Kernel is stock linux-2.6.5.
Chipset is nForce 2 (OHCI), USB 2 EHCI controller disabled, so just USB 1.1 controller active.
Please CC me if more information would be handy.
Harvested from kernel logs:
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)ohci_hcd: block sizes: ed 64 td 64ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller ohci_hcd 0000:00:02.0: USB HC TakeOver from BIOS/SMMohci_hcd 0000:00:02.0: reset, control = 0x684
PCI: Setting latency timer of device 0000:00:02.0 to 64ohci_hcd 0000:00:02.0: irq 20, pci mem e080a000ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb1: Product: nVidia Corporation nForce2 USB Controller
usb usb1: Manufacturer: Linux 2.6.5 ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
usb usb1: registering 1-0:1.0 (config #1, interface 0)
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: unknown reserved power switching mode
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all portsohci_hcd 0000:00:02.0: created debug filesohci_hcd 0000:00:02.0: OHCI controller stateohci_hcd 0000:00:02.0: OHCI 1.0, with legacy support registers ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3 ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0ohci_hcd 0000:00:02.0: intrstatus 0x00000044 RHSC SFohci_hcd 0000:00:02.0: intrenable 0x80000002 MIE WDHohci_hcd 0000:00:02.0: hcca frame #0025ohci_hcd 0000:00:02.0: roothub.a 01000203 POTPGT=1 NPS NDP=3 ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:02.0: roothub.status 00000000ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00010101 CSC PPS CCS ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2) ohci_hcd 0000:00:02.1: USB HC TakeOver from BIOS/SMMohci_hcd 0000:00:02.1: reset, control = 0x684
PCI: Setting latency timer of device 0000:00:02.1 to 64ohci_hcd 0000:00:02.1: irq 22, pci mem e080c000ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.1: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb2: Product: nVidia Corporation nForce2 USB Controller (#2) usb usb2: Manufacturer: Linux 2.6.5 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.1
usb usb2: registering 2-0:1.0 (config #1, interface 0)
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: unknown reserved power switching mode
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all portsohci_hcd 0000:00:02.1: created debug filesohci_hcd 0000:00:02.1: OHCI controller stateohci_hcd 0000:00:02.1: OHCI 1.0, with legacy support registers ohci_hcd 0000:00:02.1: control 0x683 RWE RWC HCFS=operational CBSR=3 ohci_hcd 0000:00:02.1: cmdstatus 0x00000 SOC=0ohci_hcd 0000:00:02.1: intrstatus 0x00000004 SFohci_hcd 0000:00:02.1: intrenable 0x80000002 MIE WDHohci_hcd 0000:00:02.1: hcca frame #0026ohci_hcd 0000:00:02.1: roothub.a 01000203 POTPGT=1 NPS NDP=3 ohci_hcd 0000:00:02.1: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:02.1: roothub.status 00000000ohci_hcd 0000:00:02.1: roothub.portstatus [0] 0x00000100 PPS ohci_hcd 0000:00:02.1: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:02.1: roothub.portstatus [2] 0x00000100 PPS drivers/usb/core/usb.c: registered new driver usbnetohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 1, status 101, change 1, 12 Mb/s
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101 ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-1: new full speed USB device using address 2
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3 drivers/usb/core/message.c: USB device number 2 default language ID 0x409 usb 1-1: Product: USB Cable Modem
usb 1-1: registering 1-1:1.0 (config #1, interface 0)
usbnet 1-1:1.0: usb_probe_interface
usbnet 1-1:1.0: usb_probe_interface - got id
Unable to handle kernel NULL pointer dereference at virtual address 00000004 printing eip: c028ff64 *pde = 00000000 Oops: 0000 [#1] DEBUG_PAGEALLOC CPU: 0 EIP: 0060:[<c028ff64>] Not tainted EFLAGS: 00010296 (2.6.5)
EIP is at usb_disable_interface+0x14/0x50
eax: df3a4ef8 ebx: 00000000 ecx: 00000000 edx: dffdaf38
esi: 00000001 edi: 00000000 ebp: df3aabf8 esp: df98bcfc
ds: 007b es: 007b ss: 0068
Process khubd (pid: 5, threadinfo=df98a000 task=df9bb9e0)
Stack: 00000001 0000000b 00000001 00000001 df3d5d94 df3aabf8 c0290257
df3aabf8
df3a4ef8 0000000b 00000001 00000001 00000001 00000000 00000000
00001388
00000000 df3a4ef8 df3d5d94 df3d5d94 df3d5d44 00000001 c029e301
df3aabf8
Call Trace:
[<c0290257>] usb_set_interface+0xb7/0x1a0
[<c029e301>] get_endpoints+0xb1/0x120
[<c029e4bb>] generic_cdc_bind+0xcb/0x220
[<c029e708>] cdc_bind+0x28/0xe0
[<c0263d7b>] alloc_netdev+0x7b/0xb0
[<c02a084e>] usbnet_probe+0x49e/0x510
[<c01a8a9d>] sysfs_new_inode+0x5d/0xb0
[<c0287516>] usb_probe_interface+0xb6/0xd0
[<c02526ef>] bus_match+0x3f/0x70
[<c0252761>] device_attach+0x41/0xa0
[<c0252965>] bus_add_device+0x75/0xc0
[<c0251715>] device_add+0xa5/0x140
[<c029068b>] usb_set_configuration+0x24b/0x2f0
[<c0288530>] usb_new_device+0x2d0/0x5a0
[<c028adca>] hub_port_connect_change+0x1ea/0x2f0
[<c028b2f5>] hub_events+0x425/0x5e0
[<c028b4dd>] hub_thread+0x2d/0x100
[<c01198a0>] default_wake_function+0x0/0x20
[<c028b4b0>] hub_thread+0x0/0x100
[<c0104d91>] kernel_thread_helper+0x5/0x14
Code: 80 7b 04 00 74 26 31 f6 8d 74 26 00 8b 43 0c 47 0f b6 44 30 Signature · 4 lines
Daniel J Blueman "Sie haben neue Mails!" - Die GMX Toolbar informiert Sie beim Surfen! Jetzt aktivieren unter http://www.gmx.net/info
Quoted 23 lines · Daniel Blueman
When plugging a Motorola SurfBoard 5100 device into my box, khubd oopses. Kernel is stock linux-2.6.5.
Chipset is nForce 2 (OHCI), USB 2 EHCI controller disabled, so just USB 1.1 controller active.
Please CC me if more information would be handy.
Harvested from kernel logs:
usb 1-1: Product: USB Cable Modem
usb 1-1: registering 1-1:1.0 (config #1, interface 0) usbnet 1-1:1.0:usb_probe_interface
usbnet 1-1:1.0:usb_probe_interface- got idUnable to handle kernel NULL pointer dereference at virtual address 00000004 printing eip: c028ff64 *pde = 00000000 Oops: 0000 [#1] DEBUG_PAGEALLOC CPU: 0 EIP: 0060:[<c028ff64>] Not tainted EFLAGS: 00010296 (2.6.5)
Quoted 1 line
EIP is at
usb_disable_interface+0x14/0x50
This has been fixed in 2.6.6.
Alan Stern
Alan, David,
Thanks for your response - the problem observed in linux-2.6.5 is fixed in 2.6.6. Now I get a status code of -75 [1] and see no additional networking devices.
Nothing jumps out from the ohci_q.c and related sources.
Any ideas?
--- [1]
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 1, status 101, change 1, 12 Mb/s
hub 2-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101 ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 2-1: new full speed USB device using address 3
usb 2-1: skipped 3 class/vendor specific configuration descriptors usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: default language 0x0409
usb 2-1: Product: USB Cable Modem
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usbnet 2-1:1.0: usb_probe_interface
usbnet 2-1:1.0: usb_probe_interface - got idohci_hcd 0000:00:02.1: urb da0fef78 path 1 ep0in 82d60000 cc 8 --> status -75
usbnet: probe of 2-1:1.0 failed with error -75
usb 2-1: adding 2-1:1.1 (config #1, interface 1)
Quoted 33 lines · Daniel Blueman
Quoted 2 lines
When plugging a Motorola SurfBoard 5100 device into my box, khubd
oopses.
Quoted 3 lines
Kernel is stock linux-2.6.5.
Chipset is nForce 2 (OHCI), USB 2 EHCI controller disabled, so just USB
1.1
Quoted 11 lines
controller active.
Please CC me if more information would be handy.
Harvested from kernel logs:
usb 1-1: Product: USB Cable Modem
usb 1-1: registering 1-1:1.0 (config #1, interface 0) usbnet 1-1:1.0:usb_probe_interface
usbnet 1-1:1.0:usb_probe_interface- got idUnable to handle kernel NULL pointer dereference at virtual address00000004
Quoted 9 lines
printing eip:
c028ff64
*pde = 00000000Oops: 0000 [#1] DEBUG_PAGEALLOC CPU: 0 EIP: 0060:[<c028ff64>] Not tainted EFLAGS: 00010296 (2.6.5)EIP is at
usb_disable_interface+0x14/0x50This has been fixed in 2.6.6.
Alan Stern
Signature · 4 lines
Daniel J Blueman NEU : GMX Internet.FreeDSL Ab sofort DSL-Tarif ohne Grundgebühr: http://www.gmx.net/dsl
Quoted 5 lines · Daniel Blueman
Alan, David,
Thanks for your response - the problem observed in linux-2.6.5 is fixed in 2.6.6. Now I get a status code of -75 [1] and see no additional networking devices.
In drivers/usb/core/message.c::usb_string(), try making the retry cases consider not just -EPIPE faults but also -EOVERFLOW. Likewise in the get_descriptor() logic. (Some devices seem to have firmware bugs that cause those failures, and are often amenable to retries.)
Also, this patch should help correct the "missing diagnostics with CONFIG_USB_DEBUG during CDC Ethernet probe()" issue ... and help show more precisely where the problem is.
- Dave
drivers/usb/net/usbnet.c +14 -20
@@ -107,7 +107,13 @@* *-------------------------------------------------------------------------*/ +// #define DEBUG // error path messages, extra info +// #define VERBOSE // more; success messages +#include <linux/config.h> +#ifdef CONFIG_USB_DEBUG +# define DEBUG +#endif #include <linux/module.h> #include <linux/kmod.h> #include <linux/sched.h>
@@ -120,25 +126,15 @@#include <linux/mii.h> #include <asm/uaccess.h> #include <asm/unaligned.h> - - -// #define DEBUG // error path messages, extra info -// #define VERBOSE // more; success messages -#define REALLY_QUEUE - -#if !defined (DEBUG ) && defined (CONFIG_USB_DEBUG ) -# define DEBUG -#endif #include <linux/usb.h> -#include <asm/io.h> #include <asm/scatterlist.h> #include <linux/mm.h> #include <linux/dma-mapping.h> -#define DRIVER_VERSION "25-Aug-2003" +/*-------------------------------------------------------------------------*/ /*
@@ -148,13 +144,8 @@* For high speed, each frame comfortably fits almost 36 max size * Ethernet packets (so queues should be bigger). */ -#ifdef REALLY_QUEUE #define RX_QLEN (dev) (((dev)->udev->speed == USB_SPEED_HIGH) ? 60 : 4)#define TX_QLEN (dev) (((dev)->udev->speed == USB_SPEED_HIGH) ? 60 : 4) -#else -#define RX_QLEN (dev) 1 -#define TX_QLEN (dev) 1 -#endif // packets are always ethernet inside // ... except they can be bigger (limit of 64K with NetChip framing)
@@ -1006,7 +997,7 @@if (!info->control || !info->data) {dev_dbg (&intf->dev,"master #%u/%p slave #%u/%p\n" , - info->u->bMasterInterface0 + info->u->bMasterInterface0, info->control, info->u->bSlaveInterface0, info->data);
@@ -1142,10 +1133,13 @@unsigned char buf [13 ]; tmp =usb_string (dev->udev, e->iMACAddress, buf,sizeof buf); -if (tmp <0 ) +if (tmp !=12 ) { +dev_dbg (&dev->udev->dev, +"bad MAC string %d fetch, %d\n" , e->iMACAddress, tmp); +if (tmp >=0 ) + tmp = -EINVAL ;return tmp; -else if (tmp !=12 ) -return -EINVAL ; + }for (i = tmp =0 ; i <6 ; i++, tmp +=2 ) dev->net->dev_addr [i] = (nibble (buf [tmp]) <<4 ) +nibble (buf [tmp +1 ]);