Skip to contentSkip to conversation

PROBLEM: SYM53C8XX errors while reading tape

DISCUSSION Mr. James W. Laferriere 1 participant 2 messages Nov 23, 2002 1 message not in the archive SCSI

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

Hello Russell , Sorry about taking the original reply off list I should know better . According to the dmesg & the log dumps you sent you were (were they edited?) . Please make sure that SYM53C8XX_2 driver was the only driver in the 53c8* series that was selected or That modules were not being selected anyway .

I for one KNOW that if the SYM53C8XX driver is compiled in OR listed first in the module.conf file IT will be loaded in front of the SYM53C8XX_2 and this will keep the sym2 from loading at all . And I have seen (at least three times) a condition where the SYM53C8XX_2 WAS compiled IN (just like you) and the SYM53C8XX was a module and it was -still- loaded & began conflicting with the SYM53C8XX_2 during use . Hth , JimL

ps: On my systems I have had at onetime or another almost every
(older) scsi tape drive manufactured . And damn near everytime I have had a problem it has been some mistake on my end . A bus a tad to long , the terminator I bought was just a little to good to beleive price wise ...

Quoted 8 lines · Russell Senior
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"James" == James W Laferriere <[email protected]> writes:

James> Hello Russell , Could you try the SYM53C8XX_2 driver ? I
James> beleive that this may help . JimL

I _was_ using the SYM53C8XX_2 driver. Here's the relevant portion of my .config for 2.4.18:

Quoted 6 lines

# CONFIG_SCSI_NCR53C7xx is not set
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set

--

       +------------------------------------------------------------------+
       | James   W.   Laferriere | System    Techniques | Give me VMS     |
       | Network        Engineer |     P.O. Box 854     |  Give me Linux  |
       | [email protected] | Coudersport PA 16915 |   only  on  AXP |
       +------------------------------------------------------------------+
#2 lore raw

Hello Russell , I stand(well sit) corrected . The data you sent matched exactly ,minus differant controllers, my setup after I swapped over to a python not the same vesrion as yours tho. But , Mine appears to function quite well . Had to re-install the old bugger to do this . No problems running the commands you sent along except I did not try backing up the whole '/' I just did /root whihc is ~ 288MB . Below are the cmnds in the order I ran them . I forgot to record the dmesg putput . Basically there was not any , beyond the last two lines you reported . The 'kernel:' is from an older dmesg for model & vendor info . I was of the opinion that the SYM53C8XX_2 was supposed to report
itself as sym_2: in the demsg output . I see now that it DOES
NOT do so . Which I beleive is not what Gerard had said it was to do way back when . Hth , JimL

mtx -f /dev/sg3 load 1
mt -f /dev/nst0 setblk 32768
mtx -f /dev/sg3 status
mt -f /dev/nst0 status
tar -C /root -b 64 -clvf /dev/nst0 .
mt -f /dev/nst0 status
mt -f /dev/nst0 rewind
tar -b 64 -tvf /dev/nst0
mt -f /dev/nst0 rewind
mtx -f /dev/sg3 unload
dmesg

kernel: Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
kernel:   Vendor: ARCHIVE   Model: 4586XX 28887-XXX  Rev: 0420
kernel:   Type:   Sequential-Access                  ANSI SCSI revision: 02
kernel: Detected scsi tape st0 at scsi0, channel 0, id 4, lun 0
kernel:   Vendor: ARCHIVE   Model: 4586XX 28887-XXX  Rev: 0420
kernel:   Type:   Medium Changer                     ANSI SCSI revision: 02
kernel: Detected scsi generic sgd at scsi0, channel 0, id 4, lun 1
Quoted 46 lines · Mr. James W. Laferriere

Hello Russell , Sorry about taking the original reply off list I should know better . According to the dmesg & the log dumps you sent you were (were they edited?) . Please make sure that SYM53C8XX_2 driver was the only driver in the 53c8* series that was selected or That modules were not being selected anyway .

I for one KNOW that if the SYM53C8XX driver is compiled in OR listed first in the module.conf file IT will be loaded in front of the SYM53C8XX_2 and this will keep the sym2 from loading at all . And I have seen (at least three times) a condition where the SYM53C8XX_2 WAS compiled IN (just like you) and the SYM53C8XX was a module and it was -still- loaded & began conflicting with the SYM53C8XX_2 during use . Hth , JimL

ps: On my systems I have had at onetime or another almost every
(older) scsi tape drive manufactured . And damn near everytime I have had a problem it has been some mistake on my end . A bus a tad to long , the terminator I bought was just a little to good to beleive price wise ...

Quoted 8 lines · Russell Senior
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"James" == James W Laferriere <[email protected]> writes:

James> Hello Russell , Could you try the SYM53C8XX_2 driver ? I
James> beleive that this may help . JimL

I _was_ using the SYM53C8XX_2 driver. Here's the relevant portion of my .config for 2.4.18:

Quoted 6 lines

# CONFIG_SCSI_NCR53C7xx is not set
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set

--

       +------------------------------------------------------------------+
       | James   W.   Laferriere | System    Techniques | Give me VMS     |
       | Network        Engineer |     P.O. Box 854     |  Give me Linux  |
       | [email protected] | Coudersport PA 16915 |   only  on  AXP |
       +------------------------------------------------------------------+
Quoted 5 lines

-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--

       +------------------------------------------------------------------+
       | James   W.   Laferriere | System    Techniques | Give me VMS     |
       | Network        Engineer |     P.O. Box 854     |  Give me Linux  |
       | [email protected] | Coudersport PA 16915 |   only  on  AXP |
       +------------------------------------------------------------------+