Skip to contentSkip to conversation

PROBLEM: kernel reboot before Decompressing Linux, after setting video mode

DISCUSSION [email protected] 2 participants 2 messages Sep 3, 2009 – Sep 6, 2009

lore
Share & tools
lore
#0 lore raw

[1.] One line summary of the problem:

Linux kernel 2.6.30.5 reboots after setting video mode, but before issuing the "Decompressing Linux" message.

[2.] Full description of the problem/report:

I just compiled a kernel from the official 2.6.30.5 sources using gcc 3.4.4. "make xconfig" was used to configure the kernel, and the .config was NOT edited by hand. EARLY_PRINTK=y in .config.

Initial builds failed due to unresolved ".L1234" symbols. Using "make xconfig" to disable uncompilable code resulted in a successful kernel build.

Booting the resulting kernel outputs the message "Probing EDD" and then reboots. Passing "edd=on" or "edd=off" on the kernel command line does not help; the kernel always reboots.

Passing "vga=ask" allows me to select a video mode, which appears to take effect properly. Immediately after setting the video mode, however, the machine reboots.

The problem behavior is repeatable and consistent.

[3.] Keywords (i.e., modules, networking, kernel):

boot reboot query_edd set_video go_to_protected_mode mask_all_interrupts setup_idt setup_gdt protected_mode_jump decompress_kernel

[4.] Kernel version (from /proc/version):

Attempting to boot a kernel compiled from stock 2.6.30.5 sources.

[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)

No error message is displayed. The machine simply reboots.

[6.] A small shell script or example program which triggers the
problem (if possible)

N/A. This is a problem with the early boot process. However, see diagnostic C code below.

[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)

     Gnu C                  3.4.4
     Gnu make               3.80
     binutils               2.16.1

grub 0.96

[7.2.] Processor information (from /proc/cpuinfo):

     vendor_id       : GenuineIntel
     cpu family      : 6
     model           : 8
     model name      : Pentium III (Coppermine)
     flags           : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr sse

[7.3.] Module information (from /proc/modules):

N/A. This is a problem with the early boot process.

[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)

HP Pavilion. Additional specs available as needed.

[7.5.] PCI information ('lspci -vvv' as root)
[7.6.] SCSI information (from /proc/scsi/scsi)

N/A. This is a problem with the early boot process.

[7.7.] Other information that might be relevant to the problem:

I'm assuming that this bug has something to do with relocation of the x86 setup code from assembly to C. The reboot appears to occur just after the call to mask_all_interrupts(), but before decompressing the kernel. Kernel version 2.6.15 boots without any problem, on the same machine, with the same bootloader, and with the same boot arguments. Note that set_video() is called AFTER query_edd() in arc/x86/boot/main.c, so this does not appear to be related to EDD.

In order to track down the problem, I added some puts()s to pm.c:

void pmbusywaitloop()
{
int i = 0;
int j = 1 << 27;

  for(i=0; i < j; i++) {
    /* just to make sure this loop isn't optimized out of the code */
    j--;
    j++;

}
}

/*
* Actual invocation sequence
*/
void go_to_protected_mode(void)
{
puts("Entering go_to_protected_mode\n");

  pmbusywaitloop();
	/* Hook before leaving real mode, also disables interrupts */
	realmode_switch_hook();

puts("About to enable A20 gate\n");
pmbusywaitloop();

	/* Enable the A20 gate */
	if (enable_a20()) {
		puts("A20 gate not responding, unable to boot...\n");
		die();
	}

puts("About to reset coprocessor\n");

  pmbusywaitloop();
	/* Reset coprocessor (IGNNE#) */
	reset_coprocessor();

	/* Mask all interrupts in the PIC */
  puts("About to mask interrupts\n");
  pmbusywaitloop();
	mask_all_interrupts();

	/* Actual transition to protected mode... */
  puts("About to setup IDT\n");
  pmbusywaitloop();
	setup_idt();
  puts("About to setup GDT\n");
  pmbusywaitloop();
	setup_gdt();
  puts("About to jump to protected mode\n");
  pmbusywaitloop();
	protected_mode_jump(boot_params.hdr.code32_start,
			    (u32)&boot_params + (ds() << 4));
}

When booting, the kernel outputs:

Entering go_to_protected_mode
(pause)
About to enable A20 gate
(pause)
About to reset coprocessor
(pause)
About to mask interrupts
(pause)
About to setup IDT
(pause)
(*reboot*)

Since "About to setup GDT" is never printed, I assumed that the problem was in setup_idt(). However, looking at setup_idt(), it appears that setup_idt() consists of more or less a single assembly instruction. Since I don't know if puts() requires the old IDT, I'm not able to narrow down the problem any further than this:

The reboot occurs *after* mask_all_interrupts(), but *before* the putstr("\nDecompressing Linux... ") in decompress_kernel().

#1 lore raw
Quoted 4 lines · On Thu 2009-09-03 20:49:48, [email protected] wrote:

[1.] One line summary of the problem:

Linux kernel 2.6.30.5 reboots after setting video mode, but before issuing the "Decompressing Linux" message.

Did earlier kernels work with same config? If yes, then that's rather nasty regression; cc rjw and see what happens :-).

Pavel

Quoted 19 lines

[2.] Full description of the problem/report:

I just compiled a kernel from the official 2.6.30.5 sources using gcc 3.4.4. "make xconfig" was used to configure the kernel, and the .config was NOT edited by hand. EARLY_PRINTK=y in .config.

Initial builds failed due to unresolved ".L1234" symbols. Using "make xconfig" to disable uncompilable code resulted in a successful kernel build.

Booting the resulting kernel outputs the message "Probing EDD" and then reboots. Passing "edd=on" or "edd=off" on the kernel command line does not help; the kernel always reboots.

Passing "vga=ask" allows me to select a video mode, which appears to take effect properly. Immediately after setting the video mode, however, the machine reboots.

The problem behavior is repeatable and consistent.

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html